Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge)
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292324 MANUAL TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

EC6A MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release with bearing cylinder assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 1.INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.

Coat a new O-ring with gear oil.


b.

Install the O-ring to the speedometer driven hole cover sub-assembly.


c.

Install the speedometer driven hole cover sub-assembly to the front transaxle case with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 335A0 2.INSTALL CONTROL CABLE BRACKET ASSEMBLY

a.

Install the control cable bracket assembly to the manual transmission case with the 3 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wiring harness clamp bracket to the manual transmission case with the bolt.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 87101A 4.INSTALL NO. 1 HEATER BRACKET SUB-ASSEMBLY

a.

Install the No. 1 heater bracket sub-assembly to the manual transmission case with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 31400 5.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31407B 6.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 7.INSPECT CLUTCH PIPE LINE

Hide 31407B 8.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31484 9.INSTALL CLUTCH FLEXIBLE HOSE BRACKET

a.

Install the clutch flexible hose bracket to the manual transmission case with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 31483E 10.INSTALL BLEEDER CLUTCH RELEASE TUBE

Hide 12325A 11.INSTALL ENGINE MOUNTING BRACKET LH

a.
C366693C01
0.906,1.385 1.469,1.604 0.563,0.219 10 true 1 (*a), 6 1.594,0.208 1.75,0.406 0.156,0.198 10 true 2 2.021,0.24 2.198,0.427 0.177,0.188 10 false 3 3.135,1.281 3.313,1.469 0.177,0.188 10 false 4 2.771,1.938 2.948,2.125 0.177,0.188 10 true 5
*a Temporarily Tighten


Install the engine mounting bracket LH to the manual transmission case with the 5 bolts in the order shown in the illustration.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 12364B 12.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.

Install the No. 2 engine moving control rod to the manual transmission case with the 4 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 51201 13.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Install the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


Hide 14.INSTALL ENGINE ASSEMBLY

a.
C366694C01
0.615,0.354 1.396,0.396 true 2.396,0.906 2.729,1.396 true 0.375,0.271 0.688,0.469 0.313,0.198 10 false *1 2.792,1.302 3.104,1.5 0.313,0.198 10 false *1
*1 Knock Pin


Check that the 2 knock pins are installed on the engine assembly before installing the manual transaxle assembly.


b.

Align the input shaft with the clutch disc and install the engine assembly to the manual transaxle assembly.


c.
C187765N01
1.188,0.042 1.427,0.292 0.24,0.25 10 false B 2.208,0.01 2.427,0.292 0.219,0.281 10 false A

Temporarily install the bolt (A).


d.

Install the bolt (B), then fully tighten the bolt (A).

Torque:
for Flange Bolt : 37 N*m (377 kgf*cm, 27 ft.*lbf)
for Bolt with Washer : 33 N*m (337 kgf*cm, 24 ft.*lbf)


e.

Install the 5 bolts.

Torque:
for Flange Bolt : 37 N*m (377 kgf*cm, 27 ft.*lbf)
for Bolt with Washer : 33 N*m (337 kgf*cm, 24 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the manual transaxle assembly when installing it to the engine assembly.

·

Do not apply excessive force to the manual transaxle assembly as this will break the input shaft.

·

Make sure that the knock pins fit securely into the holes when installing the manual transaxle assembly to the engine assembly.

·

Make sure that the contact surfaces of the engine assembly and manual transaxle assembly are flat against each other before tightening the bolts.




Hide 12321B 16.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Hide 17.DISCONNECT WIRE HARNESS

a.

Engage the 3 clamps and install the wire harness to the manual transaxle assembly.


b.

Connect the neutral position switch connector.


c.

Engage the 3 clamps and install the heated oxygen sensor wire harness to the front suspension crossmember sub-assembly.


d.

Engage the clamp and install the wire harness to the manual transaxle assembly.


e.

Install the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


f.

Connect the transmission revolution sensor connector.


g.

Connect the back-up light switch assembly connector.


Hide 11363A 18.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 19.INSTALL STARTER ASSEMBLY (for Cold Area Specification Vehicles)

Hide 28100 20.INSTALL STARTER ASSEMBLY (except Cold Area Specification Vehicles)

Hide 22.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE