Home › Vehicle Interior › SEAT BELT › REAR SEAT OUTER BELT ASSEMBLY › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _060065 SEAT BELT _0294238 REAR SEAT OUTER BELT ASSEMBLY A

SEAT BELT  REAR SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 73370 1.INSPECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY

Hide 73370 2.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH (for LH Side)

a.

w/o Pretensioner:

i.
B458445

Engage the guides to install the rear seat 3 point type outer belt assembly LH to the outer belt anchor bracket sub-assembly LH.


ii.

Temporarily install the nut.


iii.
B459832C01
2.948,0.625 3.104,0.823 0.156,0.198 10 true 1 1.385,1.344 1.542,1.542 0.156,0.198 10 true 2 0.271,1.448 0.427,1.646 0.156,0.198 10 true 3
V100135

Bolt (A)
V100136

Bolt (B)


Engage the guides to temporarily install the rear seat 3 point type outer belt assembly LH with bracket.


iv.

Temporarily install the 3 bolts.


v.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 42 N*m (428 kgf*cm, 31 ft.*lbf)


vi.

Tighten the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


vii.

Check that the ELR locks.

NOTICE:

This check should be performed with the rear seat 3 point type outer belt assembly LH installed to the vehicle.


1.

With the rear 3 point type seat outer belt assembly LH installed to the vehicle, check that the belt locks when it is pulled out quickly.




b.

w/ Pretensioner:

i.
B458444

Engage the guides to install the rear seat 3 point type outer belt assembly LH to the outer belt anchor bracket sub-assembly LH.


ii.

Temporarily install the nut.


iii.
B458443C01
2.24,0.583 2.448,0.708 true 2.063,0.458 2.375,0.656 0.313,0.198 10 false *a 2.635,0.302 2.948,0.5 0.313,0.198 10 false *b
*a Locking Button
*b Lock


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



iv.

Engage the clamp.


v.
B459831C01
3.01,0.583 3.167,0.781 0.156,0.198 10 true 1 1.417,1.406 1.573,1.604 0.156,0.198 10 true 2 0.375,1.51 0.531,1.708 0.156,0.198 10 true 3
V100135

Bolt (A)
V100136

Bolt (B)


Engage the guides to temporarily install the rear seat 3 point type outer belt assembly LH with bracket.


vi.

Temporarily install the 3 bolts.


vii.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 42 N*m (428 kgf*cm, 31 ft.*lbf)


viii.

Tighten the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


ix.

Check that the ELR locks.

NOTICE:

This check should be performed with the rear seat 3 point type outer belt assembly LH installed to the vehicle.


1.

With the rear seat 3 point type outer belt assembly LH installed to the vehicle, check that the belt locks when it is pulled out quickly.




c.
B458436C01
1.01,1.156 0.438,0.708 0.438,0.708 1.156,0.365 true 0.26,0.594 0.573,0.792 0.313,0.198 10 false *a
*a Protruding Part


Connect the floor anchor of the rear seat 3 point type outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not allow the anchor part of the rear seat 3 point type outer belt assembly LH to overlap the protruding parts of the floor panel.



Hide 73360 3.INSTALL REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH (for RH Side)

a.

w/o Pretensioner:

i.
B460279

Engage the guides to install the rear seat 3 point type outer belt assembly RH to the outer belt anchor bracket sub-assembly RH.


ii.

Temporarily install the nut.


iii.
B459834C01
0.271,0.667 0.427,0.865 0.156,0.198 10 true 1 2.094,1.479 2.25,1.677 0.156,0.198 10 true 2 2.917,1.75 3.073,1.948 0.156,0.198 10 true 3
V100135

Bolt (A)
V100136

Bolt (B)


Engage the guides to temporarily install the rear seat 3 point type outer belt assembly RH with bracket.


iv.

Temporarily install the 3 bolts.


v.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 42 N*m (428 kgf*cm, 31 ft.*lbf)


vi.

Tighten the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


vii.

Check that the ELR locks.

NOTICE:

This check should be performed with the rear seat 3 point type outer belt assembly RH installed to the vehicle.


1.

With the rear seat 3 point type outer belt assembly RH installed to the vehicle, check that the belt locks when it is pulled out quickly.




b.

w/ Pretensioner:

i.
B460280

Engage the guides to install the rear seat 3 point type outer belt assembly RH to the outer belt anchor bracket sub-assembly RH.


ii.

Temporarily install the nut.


iii.
B459833C01
0.26,0.708 0.417,0.906 0.156,0.198 10 true 1 2,1.375 2.156,1.573 0.156,0.198 10 true 2 2.875,1.708 3.031,1.906 0.156,0.198 10 true 3
V100135

Bolt (A)
V100136

Bolt (B)


Engage the guides to temporarily install the rear seat 3 point type outer belt assembly RH with bracket.


iv.

Temporarily install the 3 bolts.


v.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
Bolt (A) : 12.5 N*m (127 kgf*cm, 9 ft.*lbf)
Bolt (B) : 42 N*m (428 kgf*cm, 31 ft.*lbf)


vi.

Tighten the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


vii.
B458447C01
2.854,0.99 2.552,0.781 true 2.292,0.458 2.604,0.656 0.313,0.198 10 false *b 2.906,0.969 3.219,1.167 0.313,0.198 10 false *a
*a Locking Button
*b Lock


Connect the pretensioner connector and lock the locking button as shown in the illustration.

NOTICE:

Securely lock the locking button.



viii.

Engage the clamp.


ix.

Check that the ELR locks.

NOTICE:

This check should be performed with the rear seat 3 point type outer belt assembly RH installed to the vehicle.


1.

With the rear seat 3 point type outer belt assembly RH installed to the vehicle, check that the belt locks when it is pulled out quickly.




c.
B458437C01
2.26,0.375 2.979,0.656 2.979,0.656 2.406,1.156 true 3.021,0.563 3.333,0.76 0.313,0.198 10 false *a
*a Protruding Part


Connect the floor anchor of the rear seat 3 point type outer belt assembly RH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not allow the anchor part of the rear seat 3 point type outer belt assembly RH to overlap the protruding parts of the floor panel.



Hide 62480A 4.INSTALL ROOF SIDE INNER GARNISH ASSEMBLY

Hide 64740C 5.INSTALL DECK TRIM SIDE PANEL ASSEMBLY

Hide 64715C 6.INSTALL DECK TRIM SIDE COVER (w/ Cover)

Hide 81330 7.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY (w/ Luggage Compartment Room Light)

Hide 64716D 8.INSTALL DECK TRIM REAR COVER

Hide 62552F 9.INSTALL REAR SEAT SIDE GARNISH

Hide 71304C 10.INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY

Hide 62332A 11.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67918A 12.INSTALL REAR DOOR SCUFF PLATE

Hide 64997 13.INSTALL DECK FLOOR BOX LH (w/ Deck Floor Box)

Hide 64995 14.INSTALL DECK FLOOR BOX RH (w/ Deck Floor Box)

Hide 64777J 15.INSTALL SPARE WHEEL CUSHION (w/ Deck Board)

Hide 58410B 16.INSTALL DECK BOARD ASSEMBLY (w/ Deck Board)

Hide 64910J 17.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 64330D 18.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)

Hide 19.INSTALL REAR SEAT ASSEMBLY

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION