Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM
RM32H0E _58 Vehicle Interior _059647 DOOR LOCK _0294247 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the main body ECU (multiplex network body ECU) sends an unlock warning switch signal and driver door courtesy light switch signal to the combination meter assembly via CAN communication.

WIRING DIAGRAM

E358328E01
2.198,1.823 4.208,2.021 2.01,0.198 10 false Combination Meter Assembly 0.76,3 3.76,3.229 3,0.229 10 false Front Door Courtesy Light Switch Assembly LH 0.844,5.323 3.094,5.521 2.25,0.198 10 false Unlock Warning Switch Assembly 0.76,3.979 3.823,4.24 3.063,0.26 10 false Front Door Courtesy Light Switch Assembly RH 0.646,6.167 2.656,6.365 2.01,0.198 10 false : CAN Communication Line 2.646,5.927 4.656,6.125 2.01,0.198 10 false *1: for LHD 2.646,6.292 4.656,6.49 2.01,0.198 10 false *2: for RHD 3.448,5.406 5.073,5.802 1.625,0.396 10 false Instrument Panel Junction Block Assembly 5.104,5.76 6.771,6.156 1.667,0.396 10 false Main Body ECU (Multiplex Network Body ECU) 4.865,3.542 5.281,3.729 0.417,0.188 10 false F15 4.875,4.885 5.292,5.073 0.417,0.188 10 false MB 3.24,4.885 3.656,5.073 0.417,0.188 10 false 3A 4.906,3.365 5.323,3.552 0.417,0.188 10 false 27 4.927,4.698 5.344,4.885 0.417,0.188 10 false 3 3.25,4.708 3.667,4.896 0.417,0.188 10 false 41 6,4.375 6.417,4.563 0.417,0.188 10 false +B 6.031,3.063 6.448,3.25 0.417,0.188 10 false +B 6,2.063 6.417,2.25 0.417,0.188 10 false +B 5.188,2.396 5.74,2.573 0.552,0.177 10 false FLCY*1 5.208,3.396 5.76,3.573 0.552,0.177 10 false FRCY*2 5.198,4.75 5.75,4.927 0.552,0.177 10 false KSW 0.76,3.823 1.177,4.01 0.417,0.188 10 false M54 6.479,3.417 6.896,3.604 0.417,0.188 10 false IC 6.458,4.781 6.875,4.969 0.417,0.188 10 false IC 6.479,2.458 6.896,2.646 0.417,0.188 10 false IC 2.396,2.438 2.813,2.625 0.417,0.188 10 false 1 2.385,3.417 2.802,3.604 0.417,0.188 10 false 1 2.5,4.802 2.917,4.99 0.417,0.188 10 false 1 0.854,5.146 1.271,5.333 0.417,0.188 10 false F13 1.208,4.802 1.625,4.99 0.417,0.188 10 false 2 1.396,4.813 1.813,5 0.417,0.188 10 false UN- 2.125,4.802 2.542,4.99 0.417,0.188 10 false UN+ 0.75,2.844 1.167,3.031 0.417,0.188 10 false M11 4.865,2.563 5.281,2.75 0.417,0.188 10 false F15 4.917,2.375 5.333,2.563 0.417,0.188 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

The key reminder warning system uses the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the key reminder warning system after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Turn the ignition switch to ON. Place luggage on the front passenger seat to cause the seat belt warning light to blink.


b.

When driving the vehicle at 20 km/h (12 mph) or higher, check that the seat belt warning buzzer sounds to inform that the front passenger seat belt is not fastened.

HINT:

The key reminder warning system sounds the buzzer built into the combination meter assembly as a key reminder warning. This buzzer is also used for the seat belt warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the seat belt is not fastened.


OK:

Combination meter buzzer sounds.



Result:
Result Proceed to
ON (for RHD) A
ON (for LHD) B
NG C



A

2.READ VALUE USING GTS (FR Door Courtesy SW)

B

9.READ VALUE USING GTS (FL Door Courtesy SW)

C

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (FR Door Courtesy SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch assembly RH signal OFF or ON OFF: Front door RH closed
ON: Front door RH open
-
Body Electrical > Main Body > Data List
Tester Display
FR Door Courtesy SW
50003 123 197
OK:

The GTS indicates ON or OFF according to the driver door conditions shown in the table.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (Key Unlock Warning SW)

NG

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
3.READ VALUE USING GTS (Key Unlock Warning SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal OFF or ON OFF: No key in ignition key cylinder
ON: Key in ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

The GTS indicates ON or OFF according to whether the key is in the ignition key cylinder.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
4.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F13 unlock warning switch assembly connector.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-1 (UN+) - 3A-41 Always Below 1 Ω
F13-2 (UN-) - Body ground Always Below 1 Ω
F13-1 (UN+) or 3A-41 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


E358329C01
4.917,0.5 5.417,0.75 0.5,0.25 1.417,0.167 1.917,0.417 0.5,0.25 3.781,1.125 3.583,1.417 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 3.396,1.448 3.854,1.646 0.458,0.198 10 false KSW 5.073,0.531 5.531,0.729 0.458,0.198 10 false MB 1.583,0.188 2.042,0.385 0.458,0.198 10 false 3A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-41 - MB-3 (KSW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the M54 front door courtesy light switch assembly RH connector.


b.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M54-1 - F15-27 (FRCY) Always Below 1 Ω
M54-1 or F15-27 (FRCY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.READ VALUE USING GTS (FL Door Courtesy SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Door Courtesy SW Front door courtesy light switch assembly LH signal OFF or ON OFF: Front door LH closed
ON: Front door LH open
-
Body Electrical > Main Body > Data List
Tester Display
FL Door Courtesy SW
50003 123 199
OK:

The GTS indicates ON or OFF according to the driver door conditions shown in the table.



Result:
Proceed to
OK
NG



OK

10.READ VALUE USING GTS (Key Unlock Warning SW)

NG

14.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
10.READ VALUE USING GTS (Key Unlock Warning SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal OFF or ON OFF: No key in ignition key cylinder
ON: Key in ignition key cylinder
-
Body Electrical > Main Body > Data List
Tester Display
Key Unlock Warning SW
50003 123 32
OK:

The GTS indicates ON or OFF according to whether the key is in the ignition key cylinder.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

11.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
11.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F13 unlock warning switch assembly connector.


b.

Disconnect the 3A instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-1 (UN+) - 3A-41 Always Below 1 Ω
F13-2 (UN-) - Body ground Always Below 1 Ω
F13-1 (UN+) or 3A-41 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.


E358329C01
4.917,0.5 5.417,0.75 0.5,0.25 1.417,0.167 1.917,0.417 0.5,0.25 3.781,1.125 3.583,1.417 true 0.083,0.052 0.396,0.208 0.313,0.156 10 false *a 3.396,1.448 3.854,1.646 0.458,0.198 10 false KSW 5.073,0.531 5.531,0.729 0.458,0.198 10 false MB 1.583,0.188 2.042,0.385 0.458,0.198 10 false 3A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -



b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-41 - MB-3 (KSW) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

14.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

15.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the M11 front door courtesy light switch assembly LH connector.


b.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M11-1 - F15-6 (FLCY) Always Below 1 Ω
M11-1 or F15-6 (FLCY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR