Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1237  Speed Sensor Rotor Faulty  


DESCRIPTION

The skid control ECU (brake actuator assembly) measures the speed of each wheel by receiving signals from each speed sensor.

These signals are used for recognizing that all four wheels are operating properly.

Therefore, signals from all wheels must be equal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1237 Speed Sensor Rotor Faulty Any of the following is detected:
1.

Discrepancy among four wheel speed sensor output.

2.

Abnormal pulse signals from 3 or more sensors.

3.

Continuous ABS control is performed for 60 seconds or more.

4.

VSC control is performed for 10 seconds or more.


·

Tire and wheel size

·

Tire deformation

·

Speed sensor rotor

·

Speed sensor

·

Speed sensor circuit

·

Skid control ECU (brake actuator assembly)



DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4
Diagnosis Condition - - - - -
Malfunction Status Discrepancy among four wheel speed sensor output. ○ - - -
Abnormal pulse signals. - ○ - -
Continuous ABS control is performed. - - ○ -
VSC control is performed. - - - ○
Detection Time - 3 seconds or more 60 seconds or more 10 seconds or more
Number of Trips 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

Refer to DTCs C1330, C1331, C1332, C1333, C1464, C1465, C1466 and C1467.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1330

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.RECONFIRM DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.


e.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105

Result:
Result Proceed to
C1237 is output A
C1237 and C1330, C1331, C1332, C1333, 1464, C1465, C1466, C1467 are output simultaneously B



A

2.CHECK TIRES

B

GO TO DTCS (C1330, C1331, C1332, C1333, 1464, C1465, C1466 and/or C1467)

2.CHECK TIRES
a.

Check the size and condition of all four tires.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION

HINT:

The DTC is output when tire deformation or a difference in tire size is detected.


OK:

The diameter of all four tires and the tire pressure are the same.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (SPEED SENSOR)

NG

REPLACE TIRES SO THAT ALL FOUR TIRES ARE THE SAME SIZE

3.READ VALUE USING GTS (SPEED SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
50003 105 1,2,3,4

d.

Check the speed sensor output value.

OK:

The output value changes in accordance with the vehicle speed.



Result:
Result Proceed to
OK A
NG (The output value for front speed sensor RH does not change in accordance with the vehicle speed) B
NG (The output value for front speed sensor LH does not change in accordance with the vehicle speed) C
NG (The output value for rear speed sensor RH does not change in accordance with the vehicle speed) (for 2WD) D
NG (The output value for rear speed sensor RH does not change in accordance with the vehicle speed) (for AWD) E
NG (The output value for rear speed sensor LH does not change in accordance with the vehicle speed) (for 2WD) F
NG (The output value for rear speed sensor LH does not change in accordance with the vehicle speed) (for AWD) G
NG (The Test Mode (Signal Check) inspection item for 2 or more sensors does not change from incomplete to complete) (for LHD) H
NG (The Test Mode (Signal Check) inspection item for 2 or more sensors does not change from incomplete to complete) (for RHD) I



A

4.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

B

5.CHECK FRONT SPEED SENSOR RH INSTALLATION

C

12.CHECK FRONT SPEED SENSOR LH INSTALLATION

D

19.CHECK REAR SPEED SENSOR RH INSTALLATION

E

26.CHECK REAR SPEED SENSOR RH INSTALLATION

F

35.CHECK REAR SPEED SENSOR LH INSTALLATION

G

42.CHECK REAR SPEED SENSOR LH INSTALLATION

H

I

4.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Perform the sensor check using Test Mode (Signal Check) Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC/EPB > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode (Signal Check) inspection items change from incomplete to complete.


Result:
Result Proceed to
OK A
NG (The Test Mode (Signal Check) inspection item for front speed sensor RH does not change from incomplete to complete) B
NG (The Test Mode (Signal Check) inspection item for front speed sensor LH does not change from incomplete to complete) C
NG (The Test Mode (Signal Check) inspection item for rear speed sensor RH does not change from incomplete to complete) (for 2WD) D
NG (The Test Mode (Signal Check) inspection item for rear speed sensor RH does not change from incomplete to complete) (for AWD) E
NG (The Test Mode (Signal Check) inspection item for rear speed sensor LH does not change from incomplete to complete) (for 2WD) F
NG (The Test Mode (Signal Check) inspection item for rear speed sensor LH does not change from incomplete to complete) (for AWD) G
NG (The Test Mode (Signal Check) inspection item for 2 or more sensors does not change from incomplete to complete) (for LHD) H
NG (The Test Mode (Signal Check) inspection item for 2 or more sensors does not change from incomplete to complete) (for RHD) I




A

B

5.CHECK FRONT SPEED SENSOR RH INSTALLATION

C

12.CHECK FRONT SPEED SENSOR LH INSTALLATION

D

19.CHECK REAR SPEED SENSOR RH INSTALLATION

E

26.CHECK REAR SPEED SENSOR RH INSTALLATION

F

35.CHECK REAR SPEED SENSOR LH INSTALLATION

G

42.CHECK REAR SPEED SENSOR LH INSTALLATION

H

I

5.CHECK FRONT SPEED SENSOR RH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor RH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle RH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR RH

6.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

7.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR RH

7.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375627C05
0.333,0.813 0.75,1.125 0.417,0.313 1.875,0.823 2.521,1.135 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 0.427,0.906 0.885,1.104 0.458,0.198 10 false A25 2.625,1.104 3.083,1.302 0.458,0.198 10 false FR+
*a Front view of wire harness connector
(to Front Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the front speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A25-1 (FR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR RH)
8.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375627C06
0.281,0.844 0.688,1.115 0.406,0.271 1.094,1.542 1.531,0.854 true 2.24,1.552 1.875,0.854 true 0.073,0.198 0.385,0.396 0.313,0.198 10 false *a 0.375,0.917 0.833,1.115 0.458,0.198 10 false A25 2.156,1.604 2.615,1.802 0.458,0.198 10 false FR+ 1,1.604 1.458,1.802 0.458,0.198 10 false FR-
*a Front view of wire harness connector
(to Front Speed Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A25-1 (FR+) - A25-2 (FR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

9.CHECK FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY RH) (CHECK FOR FOREIGN MATTER)

NG

11.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR RH)
9.CHECK FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY RH) (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor rotor (front axle hub assembly RH).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The front speed sensor rotor is incorporated into the front axle hub assembly.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub assembly.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY RH

C

CLEAN FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY RH)

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR RH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-26 (FR-) - A25-2 (FR-) Always Below 1 Ω
A42-26 (FR-) or A25-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR RH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-26 (FR-) - A25-2 (FR-) Always Below 1 Ω
A42-26 (FR-) or A25-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK FRONT SPEED SENSOR LH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor LH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle LH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

13.CHECK FRONT SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR LH

13.CHECK FRONT SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)
a.

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

14.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR LH

14.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375627C07
0.333,0.813 0.75,1.125 0.417,0.313 1.875,0.823 2.521,1.135 true 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 0.427,0.906 0.885,1.104 0.458,0.198 10 false A13 2.625,1.104 3.083,1.302 0.458,0.198 10 false FL+
*a Front view of wire harness connector
(to Front Speed Sensor LH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the front speed sensor LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-1 (FL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

15.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

17.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR LH)
15.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375627C08
0.281,0.844 0.688,1.115 0.406,0.271 1.094,1.542 1.531,0.854 true 2.24,1.552 1.875,0.854 true 0.073,0.198 0.385,0.396 0.313,0.198 10 false *a 0.375,0.917 0.833,1.115 0.458,0.198 10 false A13 2.156,1.604 2.615,1.802 0.458,0.198 10 false FL+ 1,1.604 1.458,1.802 0.458,0.198 10 false FL-
*a Front view of wire harness connector
(to Front Speed Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-1 (FL+) - A13-2 (FL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

16.CHECK FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY LH) (CHECK FOR FOREIGN MATTER)

NG

18.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR LH)
16.CHECK FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY LH) (CHECK FOR FOREIGN MATTER)
a.

Remove the front speed sensor rotor (front axle hub assembly LH).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The front speed sensor rotor is incorporated into the front axle hub assembly.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub assembly.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY LH

C

CLEAN FRONT SPEED SENSOR ROTOR (FRONT AXLE HUB ASSEMBLY RH)

17.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR LH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-7 (FL-) - A13-2 (FL-) Always Below 1 Ω
A42-7 (FL-) or A13-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR LH)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-7 (FL-) - A13-2 (FL-) Always Below 1 Ω
A42-7 (FL-) or A13-2 (FR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor RH
*a OK
*b NG
*c No Clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly RH cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly RH.



Result:
Proceed to
OK
NG



OK

20.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

20.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375628C05
0.354,0.979 0.74,1.25 0.385,0.271 2.365,1.813 1.844,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,1.063 0.771,1.26 0.313,0.198 10 false d1 2.438,1.781 2.781,2 0.344,0.219 10 false RR+
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the rear speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-2 (RR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

21.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

22.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
21.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375628C06
0.323,0.979 0.729,1.302 0.406,0.323 1.125,1.729 1.542,1.135 true 2.271,1.771 1.844,1.156 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.448,1.073 0.76,1.271 0.313,0.198 10 false d1 2.292,1.781 2.615,1.979 0.323,0.198 10 false RR+ 1.01,1.76 1.385,1.979 0.375,0.219 10 false RR-
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-2 (RR+) - d1-1 (RR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

NG

24.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
22.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C39
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RR- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RR+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RR- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RR+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false d1 2.344,0.656 2.656,0.813 0.313,0.156 10 false dM1
*1 Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (RR-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (RR-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)

23.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A42-37 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C39
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RR- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RR+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RR- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RR+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false d1 2.344,0.656 2.656,0.813 0.313,0.156 10 false dM1
*1 Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (RR-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (RR-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

25.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)

25.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A42-37 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.CHECK REAR SPEED SENSOR RH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor RH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier sub-assembly RH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

27.CHECK REAR SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SPEED SENSOR RH

27.CHECK REAR SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

28.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE REAR SPEED SENSOR RH

28.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375628C05
0.354,0.979 0.74,1.25 0.385,0.271 2.365,1.813 1.844,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,1.063 0.771,1.26 0.313,0.198 10 false d1 2.438,1.781 2.781,2 0.344,0.219 10 false RR+
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the rear speed sensor RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-2 (RR+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

29.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

31.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
29.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375628C06
0.323,0.979 0.729,1.302 0.406,0.323 1.125,1.729 1.542,1.135 true 2.271,1.771 1.844,1.156 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.448,1.073 0.76,1.271 0.313,0.198 10 false d1 2.292,1.781 2.615,1.979 0.323,0.198 10 false RR+ 1.01,1.76 1.385,1.979 0.375,0.219 10 false RR-
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-2 (RR+) - d1-1 (RR-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

30.CHECK REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY RH) (CHECK FOR FOREIGN MATTER)

NG

33.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
30.CHECK REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY RH) (CHECK FOR FOREIGN MATTER)
a.

Remove the rear speed sensor rotor (rear axle hub and bearing assembly RH).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly RH.

·

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly RH.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY RH

C

CLEAN REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY RH)

31.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C39
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RR- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RR+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RR- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RR+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false d1 2.344,0.656 2.656,0.813 0.313,0.156 10 false dM1
*1 Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (RR-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (RR-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

32.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)

32.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A42-37 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.INSPECT SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C39
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RR- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RR+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RR- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RR+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false d1 2.344,0.656 2.656,0.813 0.313,0.156 10 false dM1
*1 Skid Control Sensor Wire RH (No. 1 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire RH (No. 1 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-1 (RR-) - dM1-2 (RR-) Always Below 1 Ω
d1-1 (RR-) - dM1-1 (RR+) Always 10 kΩ or higher
d1-1 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

34.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY)

34.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE RH (NO. 1 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-37 (RR-) - dM1-2 (RR-) Always Below 1 Ω
A42-37 (RR-) or dM1-2 (RR-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

35.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C210569C07
0.99,0.438 1.281,0.219 false 0.927,1.708 1.24,1.906 0.313,0.198 10 *a 2.344,1.698 2.656,1.896 0.313,0.198 10 *b 0.073,0.052 0.385,0.25 0.313,0.198 10 *1 1.344,0.104 1.656,0.302 0.313,0.198 10 *c
*1 Rear Speed Sensor LH
*a OK
*b NG
*c No Clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle hub.


HINT:

Because the rear axle hub and bearing assembly LH cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly LH.



Result:
Proceed to
OK
NG



OK

36.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

36.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375628C07
0.354,0.979 0.74,1.25 0.385,0.271 2.365,1.813 1.844,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,1.063 0.771,1.26 0.313,0.198 10 false e1 2.438,1.781 2.781,2 0.344,0.219 10 false RL+
*a Front view of wire harness connector
(to Rear Speed Sensor LH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the rear speed sensor LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-2 (RL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

37.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

38.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
37.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375628C08
0.323,0.979 0.729,1.302 0.406,0.323 1.125,1.729 1.542,1.135 true 2.271,1.771 1.844,1.156 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.448,1.073 0.76,1.271 0.313,0.198 10 false e1 2.292,1.781 2.615,1.979 0.323,0.198 10 false RL+ 1.01,1.76 1.385,1.979 0.375,0.219 10 false RL-
*a Front view of wire harness connector
(to Rear Speed Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-2 (RL+) - e1-1 (RL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

NG

40.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
38.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C40
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RL- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RL+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RL- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RL+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false e1 2.344,0.656 2.656,0.813 0.313,0.156 10 false eM1
*1 Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-1 (RL-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (RL-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

39.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)

39.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-23 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A42-23 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C40
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RL- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RL+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RL- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RL+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false e1 2.344,0.656 2.656,0.813 0.313,0.156 10 false eM1
*1 Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-1 (RL-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (RL-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

41.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)

41.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-23 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A42-23 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

42.CHECK REAR SPEED SENSOR LH INSTALLATION
a.
C168336C10
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Rear Speed Sensor LH
*a Correct
*b Incorrect
*c 8.5 N*m
*d No clearance


Turn the ignition switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the rear axle carrier sub-assembly LH.

The installation bolt is tightened properly.

Torque:

8.5 N*m (87 kgf*cm, 75 in.*lbf)



Result:
Proceed to
OK
NG



OK

43.CHECK REAR SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE REAR SPEED SENSOR RH

43.CHECK REAR SPEED SENSOR LH (CHECK FOR FOREIGN MATTER)

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor, clean the speed sensor.

·

If the speed sensor is damaged, replace the speed sensor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE




Result:
Proceed to
OK
NG



OK

44.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)

NG

CLEAN OR REPLACE REAR SPEED SENSOR LH

44.INSPECT BRAKE ACTUATOR ASSEMBLY (POWER SOURCE CIRCUIT)
a.
C375628C07
0.354,0.979 0.74,1.25 0.385,0.271 2.365,1.813 1.844,1.146 true 0.208,0.188 0.521,0.385 0.313,0.198 10 false *a 0.458,1.063 0.771,1.26 0.313,0.198 10 false e1 2.438,1.781 2.781,2 0.344,0.219 10 false RL+
*a Front view of wire harness connector
(to Rear Speed Sensor RH)


Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the rear speed sensor LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-2 (RL+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

45.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)

NG

47.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
45.INSPECT BRAKE ACTUATOR ASSEMBLY (GROUND CIRCUIT)
a.
C375628C08
0.323,0.979 0.729,1.302 0.406,0.323 1.125,1.729 1.542,1.135 true 2.271,1.771 1.844,1.156 true 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 0.448,1.073 0.76,1.271 0.313,0.198 10 false e1 2.292,1.781 2.615,1.979 0.323,0.198 10 false RL+ 1.01,1.76 1.385,1.979 0.375,0.219 10 false RL-
*a Front view of wire harness connector
(to Rear Speed Sensor LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
e1-2 (RL+) - e1-1 (RL-) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

46.CHECK REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY LH) (CHECK FOR FOREIGN MATTER)

NG

49.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
46.CHECK REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY LH) (CHECK FOR FOREIGN MATTER)
a.

Remove the rear speed sensor rotor (rear axle hub and bearing assembly LH).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE HUB>REMOVAL


b.

Check the speed sensor rotor.

OK:

The rotor is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the speed sensor rotor, clean the speed sensor rotor.

·

If the speed sensor rotor is damaged, replace the speed sensor rotor with a new one.

·

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



HINT:
·

The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly LH.

·

If the rear speed sensor rotor needs to be replaced, replace it together with the rear axle hub and bearing assembly LH.




Result:
Result Proceed to
OK A
NG (The speed sensor rotor is damaged.) B
NG (There is foreign matter on the speed sensor rotor.) C



A

B

REPLACE REAR AXLE HUB AND BEARING ASSEMBLY LH

C

CLEAN REAR SPEED SENSOR ROTOR (REAR AXLE HUB AND BEARING ASSEMBLY LH)

47.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C40
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RL- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RL+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RL- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RL+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false e1 2.344,0.656 2.656,0.813 0.313,0.156 10 false eM1
*1 Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-1 (RL-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (RL-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

48.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)

48.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-23 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A42-23 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

49.INSPECT SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)
a.
C367773C40
0.833,0.563 1.333,0.813 0.5,0.25 2.229,0.583 2.729,0.833 0.5,0.25 0.927,1.781 0.583,2.5 true 0.927,1.781 0.583,2.5 true 1.156,1.781 1.438,2.51 true 2.344,1.948 2.125,2.365 true 2.615,1.938 2.865,2.344 true 0.25,0.208 0.563,0.365 0.313,0.156 10 false *1 0.99,1.052 1.302,1.208 0.313,0.156 10 false *a 2.406,1.083 2.719,1.24 0.313,0.156 10 false *b 0.469,2.521 0.833,2.698 0.365,0.177 10 false RL- 1.344,2.552 1.667,2.74 0.323,0.188 10 false RL+ 2.771,2.344 3.135,2.531 0.365,0.188 10 false RL- 2.01,2.375 2.354,2.552 0.344,0.177 10 false RL+ 1.01,0.635 1.323,0.792 0.313,0.156 10 false e1 2.344,0.656 2.656,0.813 0.313,0.156 10 false eM1
*1 Skid Control Sensor Wire LH (No. 2 Parking Brake Wire Assembly)
*a Front view of wire harness connector
(to Sensor Side Connector)
*b Front view of wire harness connector
(to Vehicle Side Connector)


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



c.

Remove the skid control sensor wire LH (No. 2 parking brake wire assembly).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
e1-1 (RL-) - eM1-2 (RL-) Always Below 1 Ω
e1-1 (RL-) - eM1-1 (RL+) Always 10 kΩ or higher
e1-1 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

50.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))

NG

REPLACE SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY)

50.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SKID CONTROL SENSOR WIRE LH (NO. 2 PARKING BRAKE WIRE ASSEMBLY))
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-23 (RL-) - eM1-2 (RL-) Always Below 1 Ω
A42-23 (RL-) or eM1-2 (RL-) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR