Home › Engine / Hybrid System › 3ZR-FAE (COOLING) › RADIATOR › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _060196 3ZR-FAE COOLING _0295095 RADIATOR A

3ZR-FAE COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 1.INSTALL RADIATOR DRAIN COCK PLUG

a.

Install the O-ring to the radiator drain cock plug.

NOTICE:

Replace the O-ring if it is damaged.



b.

Install the radiator drain cock plug.


Hide 16533C 2.INSTALL RADIATOR SUPPORT GROMMET

a.

Install the 2 radiator support grommets to the radiator assembly.


Hide 16523A 3.INSTALL RADIATOR SUPPORT CUSHION

a.

Install the 2 radiator support cushions to the radiator assembly.


Hide 16400 4.INSTALL RADIATOR ASSEMBLY

a.

Engage the 2 guides.


b.

Engage the 2 claws to install the fan shroud assembly to the radiator assembly.

NOTICE:

Do not damage the radiator assembly when installing the fan shroud assembly.



c.

Install the radiator assembly together with the fan shroud assembly to the vehicle.


Hide 88460 5.INSTALL COOLER CONDENSER ASSEMBLY

Hide 88716A 6.CONNECT COOLER REFRIGERANT LIQUID PIPE A

Hide 88703 7.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 16595B 8.INSTALL NO. 1 RADIATOR AIR GUIDE LH

Hide 16593B 9.INSTALL NO. 1 RADIATOR AIR GUIDE RH

Hide 52131A 10.INSTALL FRONT BUMPER REINFORCEMENT

Hide 52611 11.INSTALL FRONT BUMPER ENERGY ABSORBER

Hide 16572D 12.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the radiator assembly and slide the clip to secure it.


b.

Engage the clamp to the fan shroud.


Hide 16573B 13.CONNECT NO. 3 RADIATOR HOSE

a.

Connect the No. 3 radiator hose to the radiator assembly and slide the clip to secure it.


Hide 16267 14.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the radiator assembly and slide the clip to secure it.


b.

Engage the 4 clamps to the fan shroud.


Hide 16261 15.CONNECT NO. 1 WATER BY-PASS HOSE

a.

Connect the No. 1 water by-pass hose to the radiator assembly and slide the clip to secure it.


Hide 16577C 16.CONNECT RADIATOR PIPE

a.

Connect the radiator pipe to the fan shroud, and then install the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 16594 17.INSTALL NO. 2 RADIATOR AIR GUIDE

a.

Engage the 4 claws to install the No. 2 radiator air guide to the radiator assembly.


Hide 53205 18.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY

a.

Install the upper radiator support sub-assembly together with the hood lock support sub-assembly to the vehicle with the 5 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


b.

Engage the clamp to connect the wire harnesses to the cooling fan ECU and fan shroud.


c.

Engage the 3 clamps to connect the wire harness to the horn and hood lock support assembly.


d.

Engage the clamp to connect the hood control cable sub-assembly to the upper radiator support sub-assembly.


Hide 53510 19.INSTALL HOOD LOCK ASSEMBLY

Hide 16561C 21.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL

Hide 53117C 22.INSTALL NO. 1 RADIATOR GRILLE RETAINER

Hide 52021B 23.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY

a.

Install the front bumper upper reinforcement sub-assembly to the vehicle with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 17751 24.INSTALL NO. 1 AIR CLEANER INLET

a.

Install the No. 1 air cleaner inlet to the upper radiator support sub-assembly and air cleaner case sub-assembly with the 4 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 26.INSTALL HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 27.ADD ENGINE COOLANT

Hide 28. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 51441 30.INSTALL NO. 1 ENGINE UNDER COVER