Home › Vehicle Interior › HEATING / AIR CONDITIONING › CONDENSER › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0295314 CONDENSER A

HEATING / AIR CONDITIONING  CONDENSER  INSTALLATION  


PROCEDURE

Hide 88460 1.INSTALL COOLER CONDENSER ASSEMBLY

a.
I112512C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 guides and 2 claws to install the cooler condenser assembly as shown in the illustration.

NOTICE:

Do not damage the cooler condenser assembly or radiator assembly when installing the cooler condenser assembly.


HINT:

If a new cooler condenser assembly is installed, add compressor oil to the cooler condenser assembly as follows.


Capacity:

Add 40 cc (1.35 fl. oz)


Compressor Oil:

for VALEO Made

VC100YF or equivalent

for DENSO Made

ND-OIL 8 or equivalent



Hide 88716A 2.CONNECT COOLER REFRIGERANT LIQUID PIPE A (for VALEO Made)

a.

Remove the vinyl tape from the cooler refrigerant liquid pipe A and cooler condenser assembly.


b.

Apply sufficient compressor oil to a new O-rings and fitting surfaces of the cooler refrigerant liquid pipe A

Compressor Oil:

VC100YF or equivalent



c.

Install the O-ring to the air cooler refrigerant liquid pipe A.

NOTICE:

Keep the O-rings and O-ring fitting surfaces free of foreign matter.



d.

Connect the cooler refrigerant liquid pipe A to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 88707 3.CONNECT SUCTION PIPE SUB-ASSEMBLY (for DENSO Made)

a.

Remove the vinyl tape from the open ends of the cooler condenser assembly and suction pipe sub-assembly.


b.
E253149C04
2.135,1.458 2.135,1.823 false 1.219,0.927 0.594,1.167 0.594,1.167 1.229,1.396 true 1.458,1.583 1.458,1.844 false 2.083,1.875 2.354,2.156 0.271,0.281 10 false *1 1.385,1.875 1.635,2.115 0.25,0.24 10 false *2 0.365,1.063 0.635,1.344 0.271,0.281 10 false *a
*1 Air Conditioner Tube and Accessory Assembly
*2 Piping Clamp
*a Groove


Install a new piping clamp to the suction pipe sub-assembly.

NOTICE:
·

Securely engage the inside step of the piping clamp in the suction pipe sub-assembly groove.

·

Do not widen the opening of the piping clamp more than the diameter of the suction pipe sub-assembly when installing it.

·

Do not install the piping clamp with the large diameter section in the wrong direction.




c.

Thoroughly coat 2 new O-rings and the contact surface of the suction pipe sub-assembly with compressor oil.

Compressor Oil:

ND-OIL 8 or equivalent



d.

Install the 2 O-rings to the suction pipe sub-assembly.

NOTICE:

Do not let foreign matter adhere to the O-rings or O-ring seals.



e.

Engage the cooler condenser assembly and suction pipe sub-assembly.

E336870C02
5.323,2.5 5.708,2.219 false 5.771,2.146 6.083,2.302 0.313,0.156 10 false *a
*a Large Diameter Section of Piping Clamp - -


NOTICE:

Engage the parts by holding the pipe, not the piping clamp.



f.

Securely insert the piping clamp to the point where the large diameter section of the piping clamp is covered by the cooler condenser assembly.

HINT:
·

When inserting, make sure that a click sound is heard.

·

Check that the suction pipe sub-assembly is securely inserted by pulling it.




Hide 88703 4.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

a.

Remove the vinyl tape from the discharge hose sub-assembly and the connecting part of the cooler condenser assembly.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the discharge hose sub-assembly.

Compressor Oil:

for VALEO Made

VC100YF or equivalent

for DENSO Made

ND-OIL 8 or equivalent



c.

Install the O-ring to the discharge hose sub-assembly.


d.

Connect the discharge hose sub-assembly to the cooler condenser assembly with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 16595B 5.INSTALL NO. 1 RADIATOR AIR GUIDE LH

Hide 16593B 6.INSTALL NO. 1 RADIATOR AIR GUIDE RH

Hide 52131A 7.INSTALL FRONT BUMPER REINFORCEMENT

Hide 52611 8.INSTALL FRONT BUMPER ENERGY ABSORBER

Hide 16594 9.INSTALL NO. 2 RADIATOR AIR GUIDE (for 8NR-FTS)

Hide 16594 10.INSTALL NO. 2 RADIATOR AIR GUIDE (for 3ZR-FAE)

Hide 53205 11.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for 8NR-FTS)

Hide 53205 12.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY (for 3ZR-FAE)

Hide 53510 13.INSTALL HOOD LOCK ASSEMBLY

Hide 16561C 15.INSTALL NO. 1 RADIATOR TO SUPPORT SEAL

Hide 53117C 16.INSTALL NO. 1 RADIATOR GRILLE RETAINER

Hide 52021B 17.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY (for 8NR-FTS)

Hide 52021B 18.INSTALL FRONT BUMPER UPPER REINFORCEMENT SUB-ASSEMBLY (for 3ZR-FAE)

Hide 17751 19.INSTALL NO. 1 AIR CLEANER INLET (for 8NR-FTS)

Hide 17751 20.INSTALL NO. 1 AIR CLEANER INLET (for 3ZR-FAE)

Hide 21.INSTALL HEADLIGHT ASSEMBLY LH (for Halogen Headlight)

Hide 22.INSTALL HEADLIGHT ASSEMBLY LH (for LED Headlight)

Hide 23.INSTALL HEADLIGHT ASSEMBLY RH (for Halogen Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 24.INSTALL HEADLIGHT ASSEMBLY RH (for LED Headlight)

HINT:

Use the same procedure as for the LH side.


Hide 25.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFC-134a(R134a))

Hide 26.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT (for HFO-1234yf(R1234yf))

Hide 27.WARM UP WARM UP ENGINE (for HFC-134a(R134a))

Hide 28.WARM UP WARM UP ENGINE (for HFO-1234yf(R1234yf))

Hide 29.INSPECT FOR REFRIGERANT LEAK (for HFC-134a(R134a))

Hide 30.INSPECT FOR REFRIGERANT LEAK (for HFO-1234yf(R1234yf))

Hide 53510 31.ADJUST HOOD LOCK ASSEMBLY