Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P2531  Ignition Switch Run Position Circuit Low  


DESCRIPTION

If the engine stop and start ECU receives the off signal from the ignition or starter switch assembly when communication with the ECM is normal, the engine stop and start ECU will output DTC P2531.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P2531 Ignition Switch Run Position Circuit Low Both of the following conditions are met for 10 seconds or more (1 trip detection logic):
·

Ignition switch off signal is input.

·

Communication with the ECM is normal.


·

Wire harness or connector

·

Instrument panel junction block assembly (IG2 NO. 2 relay)

·

No. 1 integration relay (EFI MAIN relay)

·

Ignition or starter switch assembly

·

Engine stop and start ECU


Does not come on DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.-



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.

HINT:

If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.



i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:
·

If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery temperature at 11°C (51°F) or higher, the refresh charge will be completed.)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.



a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A392123E01
0.438,0.969 1.677,1.146 1.24,0.177 10 false EFI-MAIN NO. 1 4.042,0.969 4.865,1.135 0.823,0.167 10 false EFI NO. 3 2.406,1.5 3.229,1.667 0.823,0.167 10 false EFI-MAIN 2.031,2.031 3.771,2.281 1.74,0.25 10 false No. 1 Integration Relay 6.063,1.25 6.646,1.417 0.583,0.167 10 false MREL 6.188,1.833 6.771,2 0.583,0.167 10 false A38 6.188,2 6.771,2.167 0.583,0.167 10 false ECM 5.667,3 6.25,3.167 0.583,0.167 10 false A62 5.75,2.813 5.917,2.979 0.167,0.167 10 false 1 5.688,4 5.938,4.167 0.25,0.167 10 false 18 5.677,4.208 6.26,4.375 0.583,0.167 10 false F77 6.052,3.01 6.635,3.177 0.583,0.167 10 false +B 6.052,4.24 6.635,4.406 0.583,0.167 10 false IG2 5.896,4.854 6.979,5.271 1.083,0.417 10 false Engine Stop and Start ECU 3.51,4.333 4.594,4.5 1.083,0.167 10 false ECU-IG2 NO. 3 2.865,4.885 3.948,5.052 1.083,0.167 10 false IG2-NO. 2 0.604,4.365 1.354,4.531 0.75,0.167 10 false J/B B 0.385,5.271 1.385,5.438 1,0.167 10 false BATT-MAIN 2.01,5.583 2.427,5.75 0.417,0.167 10 false AM2 1.792,5.948 4.625,6.198 2.833,0.25 10 false Instrument Panel Junction Block Assembly 0.542,6.844 1.125,7.094 0.583,0.25 10 false Battery 2.417,6.74 2.583,6.906 0.167,0.167 10 false 5 3.792,6.74 3.958,6.906 0.167,0.167 10 false 8 2.625,6.75 3.042,6.917 0.417,0.167 10 false AM1 3.458,6.75 3.875,6.917 0.417,0.167 10 false IG1 2.26,7.167 2.677,7.333 0.417,0.167 10 false F12 2.26,7.333 4.51,7.583 2.25,0.25 10 false Ignition or Starter Switch Assembly 2.021,1.865 2.333,2.063 0.313,0.198 10 false 1B 1.896,0.719 2.052,0.917 0.156,0.198 10 false 3 1.896,1.115 2.052,1.313 0.156,0.198 10 false 6 3.406,0.708 3.563,0.906 0.156,0.198 10 false 4 3.406,1.125 3.563,1.323 0.156,0.198 10 false 5 5.76,1.125 6.031,1.417 0.271,0.292 10 false 46 1.594,4.219 1.906,4.417 0.313,0.198 10 false 3L 1.615,4 1.771,4.198 0.156,0.198 10 false 1 4.583,4.208 4.896,4.406 0.313,0.198 10 false 3D 4.573,4.01 4.885,4.208 0.313,0.198 10 false 19 4.583,4.635 4.896,4.833 0.313,0.198 10 false 3A 4.583,4.427 4.896,4.625 0.313,0.198 10 false 17 1.583,5.458 1.896,5.656 0.313,0.198 10 false 3A 1.594,5.25 1.906,5.448 0.313,0.198 10 false 44 1.563,4.635 1.875,4.833 0.313,0.198 10 false 3D 1.604,4.438 1.76,4.635 0.156,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA


PROCEDURE

1.READ VALUE USING GTS (IG SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / IG Switch.


e.

According to the display on the GTS, read the Data List.

Powertrain > Stop and Start > Data List
Tester Display
IG Switch
50003 227 19
Result:
Tester Display Result Proceed to
IG Switch ON A
OFF B




A

B

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY))
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY))
a.

Disconnect the F77 engine stop and start ECU connector.


b.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F77-18 (IG2) - 3D-19 Always Below 1 Ω
F77-18 (IG2) - Body ground and other terminals Always 10 kΩ or higher
3D-19 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

A395854C01
0.5,0.521 0.906,0.813 0.406,0.292 2.302,0.521 2.708,0.813 0.406,0.292 5.167,0.531 5.573,0.823 0.406,0.292 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 0.635,0.583 0.948,0.781 0.313,0.198 10 false 3L 2.406,0.583 2.719,0.781 0.313,0.198 10 false 3D 5.271,0.604 5.583,0.802 0.313,0.198 10 false 3A
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
3L-1 - 3D-19 Battery voltage is not applied to terminals 3A-17 and 3D-3 10 kΩ or higher
3L-1 - 3D-19 Battery voltage is applied to terminals 3A-17 and 3D-3 Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY) - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY)

4.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY) - BODY GROUND)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3D-3 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY) - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG2 NO. 2 RELAY) - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL


b.

Disconnect the F12 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-17 - F12-8 (IG1) Always Below 1 Ω
3A-17 - Body ground and other terminals Always 10 kΩ or higher
F12-8 (IG1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NO. 1 INTEGRATION RELAY (EFI MAIN RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - NO. 1 INTEGRATION RELAY (EFI MAIN RELAY))
a.

Disconnect the A62 engine stop and start ECU connector.


b.

Disconnect the 1B No. 1 integration relay connector.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A62-1 (+B) - 1B-4 Always Below 1 Ω
A62-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
1B-4 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)
a.

Inspect the No. 1 integration relay.

Click herePower Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN RELAY) - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY (EFI MAIN RELAY) - ECM)
HINT:

If communication between the GTS and vehicle is possible and SFI system data can be read 30 seconds after turning the ignition switch off a malfunction in the EFI-MAIN NO. 1 relay circuit is suspected.


a.

Disconnect the 1B No. 1 integration relay connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-5 - A38-46 (MREL) Always Below 1 Ω
1B-5 - Body ground and other terminals Always 10 kΩ or higher
A38-46 (MREL) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>8NR-FTS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY