Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059427 STOP AND START _0295332 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Stop and Start Priority Control System  


DESCRIPTION

In stop and start control status, there is normal status (standard) and stop and start priority status (Extended).

Stop and start control status can be switched to the desired mode by pressing and holding the stop and start cancel switch (electric parking brake switch assembly), or by operating the steering pad switch assembly, and the mode change is also shown on the multi-information display screen.

When the mode has been switched by pressing and holding the stop and start cancel switch (electric parking brake switch assembly), a signal is sent directly from the stop and start cancel switch (electric parking brake switch assembly) to the stop and start ECU.

When the desired mode has been selected by operating the steering pad switch assembly, a status change request signal is sent from the combination meter assembly via CAN communication to the engine stop and start ECU. Based on the selected control mode, the engine stop and start ECU performs coordinated control with the air conditioner amplifier assembly.

WIRING DIAGRAM

A398733E01
2.01,1.146 2.469,1.344 0.458,0.198 10 false F72 2.021,1.313 4.323,1.719 2.302,0.406 10 false Air Conditioning Amplifier Assembly 3.594,0.427 4.208,0.625 0.615,0.198 10 false CANH 3.635,0.771 4.25,0.969 0.615,0.198 10 false CANL 3.448,2.594 4.063,2.792 0.615,0.198 10 false CANL 4.99,2.615 5.604,2.813 0.615,0.198 10 false CANL 3.417,2.208 4.031,2.406 0.615,0.198 10 false CANH 4.969,2.229 5.583,2.427 0.615,0.198 10 false CANH 2.156,2.917 2.469,3.115 0.313,0.198 10 false F4 2.156,3.094 6.135,3.292 3.979,0.198 10 false Combination Meter Assembly 4.844,2.958 5.302,3.156 0.458,0.198 10 false F77 4.844,3.115 6.646,3.458 1.802,0.344 10 false Engine Stop and Start ECU 2.156,4.156 3.667,4.677 1.51,0.521 10 false Spiral Cable with Sensor Sub-assembly 0.208,5.417 4.49,5.615 4.281,0.198 10 false Steering Pad Switch Assembly 0.385,4.646 0.698,4.844 0.313,0.198 10 false z1 0.99,4.646 1.302,4.844 0.313,0.198 10 false z1 1.583,4.646 1.896,4.844 0.313,0.198 10 false z1 0.688,4.667 0.844,4.865 0.156,0.198 10 false 8 1.292,4.656 1.448,4.854 0.156,0.198 10 false 3 1.917,4.656 2.073,4.854 0.156,0.198 10 false 2 0.344,3.958 0.802,4.156 0.458,0.198 10 false F29 0.958,3.948 1.417,4.146 0.458,0.198 10 false F29 1.583,3.948 2.042,4.146 0.458,0.198 10 false F29 0.698,3.938 0.854,4.135 0.156,0.198 10 false 3 1.292,3.938 1.604,4.135 0.313,0.198 10 false 11 1.938,3.948 2.25,4.146 0.313,0.198 10 false 10 0.635,6.146 4.302,6.344 3.667,0.198 10 false : CAN Communication Line 4.573,4.625 5.031,4.823 0.458,0.198 10 false F67 4.552,4.771 6.49,5.354 1.938,0.583 10 false Stop and Start System Cancel Switch (Electric Parking Brake Switch Assembly) 6.063,2.406 6.677,2.604 0.615,0.198 10 false ECAN 6.542,2.302 6.698,2.5 0.156,0.198 10 false 5 5.875,4.188 6.031,4.385 0.156,0.198 10 false S 4.885,4.198 5.042,4.396 0.156,0.198 10 false E 4.708,4.094 4.865,4.292 0.156,0.198 10 false 8 6.083,4.073 6.698,4.271 0.615,0.198 10 false 11 2.094,2.104 2.406,2.302 0.313,0.198 10 false 33 2.094,2.479 2.406,2.677 0.313,0.198 10 false 28 2.365,2.188 2.979,2.385 0.615,0.198 10 false MSSL 2.354,2.573 2.969,2.771 0.615,0.198 10 false MSM+

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag ECU assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION



HINT:
·

When stop and start priority control (Extended) is selected, the operation of the air conditioning system is limited. If the customer reports that the cooling effectiveness of the air conditioning system is poor, check the selected control mode. If stop and start priority control (Extended) is selected, cancel the control mode and check if the cooling effectiveness of the air conditioning system improves. If it improves, explain to the customer that the operation of the air conditioning system was limited by stop and start control.

·

Depending on the vehicle conditions, the stop and start operation time may not change even if stop and start priority control (Extended) is selected.



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Check the problem symptoms.

HINT:
·

Check each symptom by checking the suspected areas in the table below.

·

By using the GTS and entering the following menus, the selected mode can be confirmed.

Powertrain / Stop and Start / Data List / Stop & Start A/C Mode



Result:
Problem Symptoms Trouble Area Proceed to
Multi-information display screen does not change after pressing steering pad switch assembly
·

Steering pad switch assembly

·

Spiral cable with sensor sub-assembly

·

Combination meter assembly

·

Engine stop and start ECU

·

Wire harness or connector (steering pad switch assembly - combination meter assembly)

·

Wire harness or connector (engine stop and start ECU - combination meter assembly)


A
When the stop and start cancel switch (electric parking brake switch assembly) is pressed and held, the stop and start indicator display on the multi-information display screen does not change, and control does not change. Or, the status change interrupt display in the combination meter assembly is not displayed, and control does not change
·

Stop and start system cancel switch (electric parking brake switch assembly)

·

Wire harness or connector (Stop and start system cancel switch (electric parking brake switch assembly) - engine stop and start ECU)


B
Even though the stop and start cancel switch (electric parking brake switch assembly) and steering pad switch assembly are operated, the multi-information display screen does not change, and control does not change
·

Engine stop and start ECU

·

CAN communication system


C
Multi-information display screen changes without pressing steering pad switch assembly
·

Steering pad switch assembly

·

Spiral cable with sensor sub-assembly

·

Wire harness or connector (steering pad switch assembly - combination meter assembly)


D
The stop and start indicator in the multi-information display screen does not change, but control status changes. Or, the status change interrupt display in the combination meter assembly is not displayed, but control changes Combination meter assembly E
The stop and start indicator display on the multi-information display screen changes, but control status does not change. Or, the status change interrupt display in the combination meter assembly is displayed, but control does not change
·

Air conditioning amplifier assembly

·

CAN communication system


F
Control mode returns to default mode after turning ignition switch ON Engine stop and start ECU G




A

2.CHECK OPERATION

B

C

7.CHECK DTC OUTPUT

D

8.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

E

F

11.CHECK DTC OUTPUT

G

12.CHECK DTC OUTPUT
2.CHECK OPERATION
a.

Using the steering pad switch assembly, check that all functions other than "Stop and Start A/c Mode" can be selected.

Result:
Result Proceed to
Only "Stop and Start A/C Mode" cannot be selected A
No function can be selected using the steering pad switch assembly B




A

3.CHECK DTC OUTPUT

B

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

Powertrain > Stop and Start > Trouble Codes
50001 227

f.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
CAN DTCs are output B




A

B

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the F29 spiral cable with sensor sub-assembly connector.


c.

Disconnect the F4 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-10 (+DP) - F4-28 (MSM+) Always Below 1 Ω
F29-10 (+DP) - Body ground Always 10 kΩ or higher
F4-28 (MSM+) - Body ground Always 10 kΩ or higher
F29-11 (+DP2) - F4-33 (MSSL) Always Below 1 Ω
F29-11 (+DP2) - Body ground Always 10 kΩ or higher
F4-33 (MSSL) - Body ground Always 10 kΩ or higher
F29-3 (EAU) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

6.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

6.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

Powertrain > Stop and Start > Trouble Codes
50001 227

f.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
CAN DTCs are output B




A

B

8.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the F29 spiral cable with sensor sub-assembly connector.


c.

Disconnect the F4 combination meter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-10 (+DP) - F4-28 (MSM+) Always Below 1 Ω
F29-10 (+DP) - Body ground Always 10 kΩ or higher
F4-28 (MSM1) - Body ground Always 10 kΩ or higher
F29-11 (+DP2) - F4-33 (MSSL) Always Below 1 Ω
F29-11 (+DP2) - Body ground Always 10 kΩ or higher
F4-33 (MSSL) - Body ground Always 10 kΩ or higher
F29-3 (EAU) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Inspect the spiral cable with sensor sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

10.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

10.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

11.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

Powertrain > Stop and Start > Trouble Codes
50001 227

f.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
CAN DTCs are output B




A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

12.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Perform a road test.


e.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

Powertrain > Stop and Start > Trouble Codes
50001 227

f.

Read the DTCs.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B




A

B