Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for VALEO Made) › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0293719 AIR CONDITIONING UNIT(for VALEO Made) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for VALEO Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system (Click here)
·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly

·

No. 2 Air Conditioning Radiator Damper Servo Sub-assembly

·

Air conditioning amplifier assembly


Initialize servo motor (Air conditioning system) DTCs are stored (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

*2: w/ Stop and start system

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFC-134a(R134a))

Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFO-1234yf(R1234yf))

Hide 3. DRAIN ENGINE COOLANT (for 8NR-FTS)

Hide 4. DRAIN ENGINE COOLANT (for 3ZR-FAE)

Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 6.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 7.REMOVE WATER GUARD PLATE LH

Hide 55736D 8.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 9.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 11.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 87246 12.DISCONNECT OUTLET HEATER WATER HOSE

a.
I112329

Slide the hose clip to disconnect the outlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the outlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the outlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 13.DISCONNECT INLET HEATER WATER HOSE

a.
I112330

Slide the hose clip to disconnect the inlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the inlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the inlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 88707 14.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

a.
I112331

Remove the bolt.


b.
I112332

Disconnect the suction pipe sub-assembly and cooler refrigerant liquid pipe A shown in the illustration.


c.

Remove the 2 O-rings from the suction pipe sub-assembly and cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 15.REMOVE FRONT SEAT ASSEMBLY LH

Hide 16.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 55401E 17.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 18.REMOVE STEERING COLUMN ASSEMBLY

Hide 85940 19.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY

Hide 89340A 20.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)

Hide 82877 21.REMOVE ECU INTEGRATION BOX RH (for LHD)

Hide 82878 22.REMOVE ECU INTEGRATION BOX LH (for RHD)

Hide 88625Q 23.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.
I112333

Disconnect the connector and air conditioning duct sub-assembly to remove the cooler thermistor (room temperature sensor).


Hide 55215D 24.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
I112338

Remove the 2 front floor carpet clips.


b.
I112339C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.


d.
I112343

Disengage the clips to remove the No. 3 dash panel insulator pad.


Hide 87212K 25.REMOVE REAR NO. 6 AIR DUCT (w/ Rear Air Duct)

a.
I112340C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 6 air duct as shown in the illustration.


Hide 87212J 26.REMOVE REAR NO. 5 AIR DUCT (w/ Rear Air Duct)

a.
I112341C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 5 air duct as shown in the illustration.


Hide 87212H 27.REMOVE REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

a.
I112334

Remove the 2 front floor carpet clips.


b.
I112335C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.


d.
I112336C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 4 air duct as shown in the illustration.


Hide 87212G 28.REMOVE REAR NO. 3 AIR DUCT (w/ Rear Air Duct)

a.
I112337C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 3 air duct as shown in the illustration.


Hide 87212F 29.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

a.
I112342C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 2 air duct.


Hide 87212 30.REMOVE REAR NO. 1 AIR DUCT (w/ Rear Air Duct)

a.
I112501C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 1 air duct as shown in the illustration.


Hide 55306A 31.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

w/ PTC Heater:

i.
E339409

Remove the bolt to disconnect the ground wire.



b.
I112345

Remove the 2 nuts and separate the relay block assembly.


c.

for LHD:

i.
I113757

Disengage the clamps to disconnect the wire harness.


ii.
I113758

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.



d.

for RHD:

i.
I113738

Disengage the clamps to disconnect the wire harness.


ii.
I113739

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.



Hide 55307C 32.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.
I112542

Remove the bolt to disconnect the ground wire.


ii.

Disengage the clamps to disconnect the wire harness.


iii.

Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.



b.

for RHD:

i.
I113736

Remove the bolt to disconnect the ground wire.


ii.

Disengage the clamps to disconnect the wire harness.


iii.
I113737

Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.



Hide 55308B 33.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
I112348

Disengage the clamp and claws.


b.

Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.


Hide 88539J 34.REMOVE DRAIN COOLER HOSE

a.
I112352C01
1.656,3.083 1.24,2.896 true 1.688,3 1.948,3.208 0.26,0.208 10 true *1
*1 Cooler Unit Drain Hose Grommet


Disconnect the drain cooler hose.

NOTICE:

If the cooler unit drain hose grommet is disconnected from the vehicle body while disconnecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 82141 35.DISCONNECT INSTRUMENT PANEL WIRE

a.

for LHD:

i.

Disconnect each connector.

I113769C01
0.469,1.073 0.729,0.885 true 1.646,1.365 1.865,1.219 true 3.552,1.01 3.083,1.094 3.083,1.094 2.979,0.813 true 4.521,0.375 3.958,0.188 3.958,0.188 4.177,0.385 true 6.219,0.604 5.354,0.813 5.354,0.813 5.552,1.031 true 6.167,1.313 6.448,1.354 true 6.25,2.542 6.844,2.906 6.844,2.906 6.448,3.146 true 3.875,4.281 3.708,4.979 3.708,4.979 3.198,4.281 true 2.5,4.333 2.635,3.76 2.635,3.76 2.25,4.073 true 2.531,4.656 2.583,4.854 true 0.833,4.938 1.063,5.094 true 0.542,5.271 0.771,5.427 true 0.729,0.75 0.948,0.948 0.219,0.198 10 true *a 0.344,5.146 0.552,5.333 0.208,0.188 10 true *b 1.448,1.271 1.667,1.469 0.219,0.198 10 true *a 2.99,1.125 3.208,1.323 0.219,0.198 10 true *a 3.74,0.073 3.958,0.271 0.219,0.198 10 true *a 5.104,0.698 5.323,0.896 0.219,0.198 10 true *a 5.948,1.177 6.167,1.375 0.219,0.198 10 true *a 6.875,2.802 7.094,3 0.219,0.198 10 true *a 3.635,5 3.854,5.198 0.219,0.198 10 true *a 2.677,3.635 2.896,3.833 0.219,0.198 10 true *a 2.51,4.865 2.729,5.063 0.219,0.198 10 true *a 0.969,5.094 1.188,5.292 0.219,0.198 10 true *a
*a Clamp *b Hook



ii.

Remove the bolt and screw.


iii.

Remove the 4 bolts to disconnect the 4 ground wires.


iv.

Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.


v.

Disengage clamps and hook to disconnect the instrument panel wire.



b.

for RHD:

i.

Disconnect each connector.

I113770C01
0.635,1 0.896,1.125 true 1.615,0.323 1.344,0.521 true 2.667,1.135 2.771,1.281 true 3.323,0.979 3.75,1.208 3.75,1.208 4.177,0.927 true 6.469,0.792 6.656,1.042 true 6.583,4.906 6.75,4.521 6.75,4.521 6.552,4.125 true 6.229,5.479 6.438,5.583 true 3.26,4.375 3.615,4.854 3.615,4.854 3.833,4.302 true 2.469,4.74 2.677,4.615 true 0.5,5.271 0.719,5.438 true 0.844,4.958 1.063,5.125 true 0.917,1.052 1.115,1.24 0.198,0.188 10 true *a 0.26,5.146 0.469,5.344 0.208,0.198 10 true *b 1.156,0.427 1.354,0.615 0.198,0.188 10 true *a 2.688,1.281 2.885,1.469 0.198,0.188 10 true *a 3.646,1.219 3.844,1.406 0.198,0.188 10 true *a 6.281,0.688 6.479,0.875 0.198,0.188 10 true *a 5.521,4.042 5.719,4.229 0.198,0.188 10 true A 5.604,4.354 5.802,4.542 0.198,0.188 10 true A 6.802,4.417 7,4.604 0.198,0.188 10 true *a 6.01,5.375 6.208,5.563 0.198,0.188 10 true *a 3.51,4.854 3.708,5.042 0.198,0.188 10 true *a 2.688,4.51 2.885,4.698 0.198,0.188 10 true *a 0.979,5.135 1.177,5.323 0.198,0.188 10 true *a 6.833,5.083 7.031,5.271 0.198,0.188 10 false B 5.625,0.292 5.823,0.479 0.198,0.188 10 true C 5.698,0.615 5.896,0.802 0.198,0.188 10 true C 1.927,0.344 2.125,0.531 0.198,0.188 10 true C
*a Clamp *b Hook



ii.

Remove the bolt and screw.


iii.

Remove the 4 bolts to disconnect the 4 ground wires.


iv.

Remove the 2 nuts A.


v.

Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.


vi.

Disengage clamps and hook to disconnect the instrument panel wire.



Hide 36.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
I112353

Remove the 2 bolts.


b.

Remove the 5 bolts.

I113768


c.

Remove the nut.


d.
I112356

Disengage the clamps.


e.

Disconnect 2 connectors.


f.

Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I112355C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 37.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.

I112357


Hide 55990B 38.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY

a.
I112349

Disengage the claws to remove the lower defroster nozzle assembly.