Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 5 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Main body ECU (multiplex network body ECU)

·

Certification ECU (smart key ECU assembly)

(w/ Entry and Start System)

·

Central gateway ECU (network gateway ECU)

·

Combination meter assembly

·

Air conditioning amplifier assembly

·

Headlight ECU sub-assembly LH

(for LED Headlight)

·

No. 3 CAN junction connector



WIRING DIAGRAM

C360951E03
1.365,0.906 1.979,1.104 0.615,0.198 10 false CANH 1.365,1.448 1.979,1.646 0.615,0.198 10 false CANL 0.542,1.844 1.156,2.042 0.615,0.198 10 false F15 0.542,2 2.167,2.417 1.625,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 0.583,4.177 2.104,4.594 1.521,0.417 10 false Certification ECU (Smart Key ECU Assembly)*1 0.583,4.021 1.219,4.229 0.635,0.208 10 false F1 0.323,6.521 2.292,6.938 1.969,0.417 10 false Combination Meter Assembly 0.333,6.375 0.948,6.573 0.615,0.198 10 false F4 0.719,5.708 1.333,5.906 0.615,0.198 10 false 120 Ω 5.875,1.177 6.49,1.375 0.615,0.198 10 false 120 Ω 5.24,3.115 5.854,3.313 0.615,0.198 10 false CANH 5.24,3.656 5.854,3.854 0.615,0.198 10 false CANL 1.375,3.646 1.99,3.844 0.615,0.198 10 false CANL 1.333,3.115 1.948,3.313 0.615,0.198 10 false CANH 5.25,6 5.865,6.198 0.615,0.198 10 false CANL 5.25,5.458 5.865,5.656 0.615,0.198 10 false CANH 5.24,0.813 5.854,1.01 0.615,0.198 10 false CA5H 5.25,1.354 5.865,1.552 0.615,0.198 10 false CA5L 4.979,1.833 5.594,2.031 0.615,0.198 10 false F74 4.958,1.979 6.896,2.438 1.938,0.458 10 false Central Gateway ECU (Network Gateway ECU) 4.99,4.083 6.552,4.49 1.563,0.406 10 false Air Conditioning Amplifier Assembly 4.594,3.646 5.208,3.844 0.615,0.198 10 false F72 4.917,3.646 5.531,3.844 0.615,0.198 10 false F73 4.604,3.115 5.219,3.313 0.615,0.198 10 false F72 4.917,3.115 5.531,3.313 0.615,0.198 10 false F73 4.948,2.927 5.563,3.125 0.615,0.198 10 false 11 4.677,2.927 5.292,3.125 0.615,0.198 10 false 9 4.969,3.469 5.583,3.667 0.615,0.198 10 false 12 4.625,3.469 5.24,3.667 0.615,0.198 10 false 10 4.646,3.844 5.26,4.042 0.615,0.198 10 false *3 4.979,3.844 5.594,4.042 0.615,0.198 10 false *4 4.979,3.292 5.594,3.49 0.615,0.198 10 false *4 4.646,3.292 5.26,3.49 0.615,0.198 10 false *3 5.167,6.385 5.802,6.594 0.635,0.208 10 false A16 5.167,6.552 6.417,7.063 1.25,0.51 10 false Headlight ECU Sub-assembly LH*2 4.99,5.365 5.604,5.563 0.615,0.198 10 false 24 5,5.906 5.615,6.104 0.615,0.198 10 false 23 3.969,5.906 4.583,6.104 0.615,0.198 10 false 14 3.979,5.365 4.594,5.563 0.615,0.198 10 false 3 1.844,5.365 2.458,5.563 0.615,0.198 10 false 32 1.854,5.896 2.469,6.094 0.615,0.198 10 false 31 2.74,5.365 3.354,5.563 0.615,0.198 10 false 1 2.656,5.896 3.271,6.094 0.615,0.198 10 false 12 2.542,6.385 3.156,6.583 0.615,0.198 10 false F114 2.542,6.542 4.51,6.958 1.969,0.417 10 false No. 3 CAN Junction Connector 1.844,3.01 2.458,3.208 0.615,0.198 10 false 1 1.854,3.552 2.469,3.75 0.615,0.198 10 false 2 2.708,3.01 3.323,3.208 0.615,0.198 10 false 5 2.646,3.552 3.26,3.75 0.615,0.198 10 false 16 2.656,1.344 3.271,1.542 0.615,0.198 10 false 13 1.833,1.344 2.448,1.542 0.615,0.198 10 false 13 2.719,0.813 3.052,1.063 0.333,0.25 10 false 2 1.844,0.813 2.458,1.01 0.615,0.198 10 false 14 4,3.01 4.615,3.208 0.615,0.198 10 false 4 3.99,3.552 4.604,3.75 0.615,0.198 10 false 15 3.979,1.344 4.594,1.542 0.615,0.198 10 false 17 3.979,0.813 4.594,1.01 0.615,0.198 10 false 6 4.979,1.354 5.594,1.552 0.615,0.198 10 false 16 4.979,0.813 5.594,1.01 0.615,0.198 10 false 15 0.333,7.031 2.99,7.417 2.656,0.385 10 false *1: w/ Entry and Start System 0.333,7.49 2.99,7.875 2.656,0.385 10 false *2: for LED Headlight 0.333,7.927 4.24,8.26 3.906,0.333 10 false *3: w/ Top-mounted Air Conditioner Pressure Sensor 0.333,8.354 4.24,8.688 3.906,0.333 10 false *4: w/ Side-mounted Air Conditioner Pressure Sensor 1.385,5.906 2,6.104 0.615,0.198 10 false CANL 1.354,5.375 1.969,5.573 0.615,0.198 10 false CANH

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the LDA main switch on and wait for approximately 52 seconds or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.*1

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


*1: w/ Entry and Start System



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 3 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C05
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 2.417,0.417 3.323,1.833 true 4.333,1 3.49,1.844 true 3.604,1.844 4.5,1.417 true 3.208,2.063 2.333,3.167 true 3.49,2.063 4.333,2.917 true 2.417,1.667 2.917,1.844 true 2.333,1.25 3.083,1.844 true 2.333,2.75 3.083,2.063 true 2.333,0.833 3.208,1.833 true 3.333,2.073 2.417,3.583 true 3.615,2.052 4.5,2.5 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 1.76,0.698 2.344,0.885 0.583,0.188 10 false CANH*d 1.844,0.229 2.427,0.427 0.583,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F114 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 1.771,3.135 2.333,3.323 0.563,0.188 10 false CANL*d 1.875,3.51 2.427,3.708 0.552,0.198 10 false CANL*e 4.385,0.833 4.969,1.021 0.583,0.188 10 false CANH*f 4.552,1.292 5.135,1.479 0.583,0.188 10 false CANH*g 4.583,2.417 5.135,2.615 0.552,0.198 10 false CANL*g 4.396,2.885 4.948,3.083 0.552,0.198 10 false CANL*f
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Combination Meter Assembly
*c to Main Body ECU (Multiplex Network Body ECU) *d to Headlight ECU Sub-assembly LH
(for LED Headlight)
*e to Air Conditioning Amplifier Assembly *f to Certification ECU (Smart Key ECU Assembly)
(w/ Entry and Start System)
*g to Central Gateway ECU (Network Gateway ECU) - -


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F114-1 (CANH) - F114-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
F114-2 (CANH) - F114-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
F114-3 (CANH) - F114-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Headlight ECU sub-assembly LH*1
F114-4 (CANH) - F114-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
F114-5 (CANH) - F114-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*2
F114-6 (CANH) - F114-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)


*1: for LED Headlight

*2: w/ Entry and Start System



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to combination meter assembly) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

D

4.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
2.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C366166C05
1.417,0.917 1.917,1.167 0.5,0.25 1.75,1.75 2.417,1.083 true 1.75,2.021 2.25,2.667 true 0.156,0.135 0.469,0.333 0.313,0.198 10 false *a 2.458,0.917 3.375,1.115 0.917,0.198 10 false CANH*b 2.302,2.625 3.219,2.823 0.917,0.198 10 false CANL*b 1.5,0.958 2.115,1.156 0.615,0.198 10 false F114
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F114-6 (CANH) - F114-17 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 3 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the F4 combination meter assembly connector.


b.
C366166C06
1.417,0.917 1.917,1.167 0.5,0.25 0.948,1.74 0.667,1 true 0.667,2.667 0.958,2.031 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.51,0.958 2.125,1.156 0.615,0.198 10 false F114 0.125,0.823 1.042,1.021 0.917,0.198 10 false CANH*b 0.156,2.667 1.073,2.865 0.917,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Combination Meter Assembly


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F114-1 (CANH) - F114-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

4.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367290C01
1.417,0.25 1.917,0.5 0.5,0.25 2.417,1.667 1.927,1.135 true 2.25,1.917 1.833,1.135 true 1.563,0.292 2.021,0.49 0.458,0.198 10 false F74 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 2.49,1.594 3.104,1.792 0.615,0.198 10 false CA5H 2.302,1.875 2.917,2.073 0.615,0.198 10 false CA5L
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-15 (CA5H) - F74-16 (CA5L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR