Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM U

NETWORKING  CAN COMMUNICATION SYSTEM  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 CAN JUNCTION CONNECTOR (w/o Blind Spot Monitor System)


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

C366168C21
3.333,1.083 3.833,1.333 0.5,0.25 2.5,1.417 3.052,1.844 true 2.667,0.75 3.292,1.844 true 3.479,1.844 2.75,0.417 true 2.5,2.5 3.052,2.063 true 3.333,2.073 2.667,3.167 true 3.469,2.073 2.75,3.5 true 2.583,1.083 3.188,1.833 true 2.417,1.667 2.927,1.885 true 2.417,2.25 2.917,2.031 true 3.208,2.073 2.583,2.833 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.927,1.229 2.844,1.427 0.917,0.198 10 false CANH*c 2.094,0.542 3.01,0.74 0.917,0.198 10 false CANH*e 2.177,0.198 3.094,0.396 0.917,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F112 1.948,2.448 2.865,2.646 0.917,0.198 10 false CANL*c 2.115,3.125 3.031,3.323 0.917,0.198 10 false CANL*e 2.198,3.49 3.115,3.688 0.917,0.198 10 false CANL*e 2.01,0.896 2.927,1.094 0.917,0.198 10 false CANH*d 1.844,1.51 2.76,1.708 0.917,0.198 10 false CANH*b 2.031,2.792 2.948,2.99 0.917,0.198 10 false CANL*d 1.854,2.167 2.771,2.365 0.917,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to Central Gateway ECU (Network Gateway ECU) - -



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F112-1 (CANH) SB Clearance warning ECU assembly*1
(for Bus 1)
F112-12 (CANL) GR
F112-2 (CANH) R Forward recognition camera*2
(for Bus 1)
F112-13 (CANL) GR
F112-3 (CANH) G Millimeter wave radar sensor assembly*2
(for Bus 1)
F112-14 (CANL) GR
F112-4 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 1)
F112-15 (CANL) GR
F112-5 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
F112-16 (CANL) GR

*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense





NO. 1 CAN JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


a.

Check the No. 1 CAN junction connector.

i.

Connection diagram

C366168C22
3.333,1.083 3.833,1.333 0.5,0.25 2.5,1.417 3.052,1.844 true 2.667,0.75 3.292,1.844 true 3.479,1.844 2.75,0.417 true 2.5,2.5 3.052,2.063 true 3.333,2.073 2.667,3.167 true 3.469,2.073 2.75,3.5 true 2.583,1.083 3.177,1.844 true 2.417,1.667 2.917,1.844 true 2.417,2.25 2.917,2.063 true 3.177,2.073 2.583,2.833 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.542 2.75,1.74 0.917,0.198 10 false CANH*b 2.01,0.927 2.927,1.125 0.917,0.198 10 false CANH*d 2.219,0.219 3.135,0.417 0.917,0.198 10 false CANH*f 3.427,1.125 4.042,1.323 0.615,0.198 10 false F112 2.219,3.521 3.135,3.719 0.917,0.198 10 false CANL*f 1.948,2.479 2.865,2.677 0.917,0.198 10 false CANL*c 2,2.802 2.917,3 0.917,0.198 10 false CANL*d 2.104,0.552 3.021,0.75 0.917,0.198 10 false CANH*e 1.927,1.25 2.844,1.448 0.917,0.198 10 false CANH*c 1.854,2.208 2.771,2.406 0.917,0.198 10 false CANL*b 2.115,3.167 3.031,3.365 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to Clearance Warning ECU Assembly
(w/ TOYOTA Parking Assist-sensor System)
*c to Forward Recognition Camera
(w/ Toyota Safety Sense)
*d to Millimeter Wave Radar Sensor Assembly
(w/ Toyota Safety Sense)
*e to No. 6 CAN Junction Connector *f to Central Gateway ECU (Network Gateway ECU)



ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F112-1 (CANH) SB Clearance warning ECU assembly*1
(for Bus 1)
F112-12 (CANL) GR
F112-2 (CANH) R Forward recognition camera*2
(for Bus 1)
F112-13 (CANL) GR
F112-3 (CANH) G Millimeter wave radar sensor assembly*2
(for Bus 1)
F112-14 (CANL) GR
F112-4 (CANH) B No. 6 CAN junction connector
(for Bus 1)
F112-15 (CANL) GR
F112-5 (CANH) P Central gateway ECU (network gateway ECU)
(for Bus 1)
F112-16 (CANL) GR

*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Toyota Safety Sense





NO. 2 CAN JUNCTION CONNECTOR (w/ Stop and Start System)


a.

Check the No. 2 CAN junction connector.

i.

Connection diagram

C366168C23
3.333,1.083 3.833,1.333 0.5,0.25 2.667,1.583 2.927,1.854 true 2.667,1.25 3.292,1.844 true 3.542,1.854 2.75,0.917 true 2.75,2.333 2.948,2.063 true 3.333,2.073 2.833,2.667 true 3.552,2.063 3,3 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 2.083,1.5 3,1.698 0.917,0.198 10 false CANH*b 2.104,1.156 3.021,1.354 0.917,0.198 10 false CANH*c 2.188,0.823 3.104,1.021 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F113 2.219,2.313 3.135,2.51 0.917,0.198 10 false CANL*b 2.292,2.615 3.208,2.813 0.917,0.198 10 false CANL*c 2.49,3 3.406,3.198 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to ECM *d to Engine Stop and Start ECU



ii.

Check the connection diagram of the components which are connected to the No. 2 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F113-1 (CANH) W Central gateway ECU (network gateway ECU)
(for Bus 2)
F113-12 (CANL) P
F113-4 (CANH) GR ECM
(for Bus 2)
F113-15 (CANL) P
F113-6 (CANH) R Engine stop and start ECU
(for Bus 2)
F113-17 (CANL) P




NO. 3 CAN JUNCTION CONNECTOR


a.

Check the No. 3 CAN junction connector.

i.

Connection diagram

C366168C24
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 2.417,0.417 3.323,1.833 true 4.667,0.417 3.49,1.844 true 3.604,1.844 4.667,0.75 true 3.208,2.063 2.333,3.167 true 3.49,2.063 4.25,3.583 true 2.417,1.667 2.917,1.844 true 2.333,1.25 3.083,1.844 true 2.333,2.75 3.083,2.063 true 2.333,0.833 3.208,1.833 true 3.333,2.073 2.417,3.583 true 3.615,2.052 4.5,3.333 true 4.229,1.844 4.667,1.76 true 3.969,1.844 4.646,1.24 true 4.104,1.844 4.667,1.5 true 4.229,2.052 4.667,2.25 true 4.115,2.052 4.667,2.531 true 3.958,2.063 4.667,2.75 true 3.833,1.833 4.667,1 true 3.813,2.063 4.667,3.083 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 1.76,0.698 2.344,0.885 0.583,0.188 10 false CANH*d 1.844,0.229 2.427,0.427 0.583,0.198 10 false CANH*e 3.427,1.125 4.042,1.323 0.615,0.198 10 false F114 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 1.771,3.135 2.333,3.323 0.563,0.188 10 false CANL*d 1.875,3.51 2.427,3.708 0.552,0.198 10 false CANL*e 4.75,0.323 5.333,0.51 0.583,0.188 10 false CANH*f 4.75,0.583 5.333,0.771 0.583,0.188 10 false CANH*g 4.583,3.302 5.135,3.5 0.552,0.198 10 false CANL*g 4.313,3.573 4.865,3.771 0.552,0.198 10 false CANL*f 4.75,1.125 5.333,1.313 0.583,0.188 10 false CANH*i 4.75,1.406 5.333,1.594 0.583,0.188 10 false CANH*g 4.76,1.667 5.344,1.854 0.583,0.188 10 false CANH*g 4.74,2.198 5.292,2.396 0.552,0.198 10 false CANL*g 4.75,2.458 5.302,2.656 0.552,0.198 10 false CANL*g 4.75,2.708 5.302,2.906 0.552,0.198 10 false CANL*i 4.75,0.854 5.333,1.042 0.583,0.188 10 false CANH*h 4.74,3.021 5.292,3.219 0.552,0.198 10 false CANL*h
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to Combination Meter Assembly
*c to Main Body ECU (Multiplex Network Body ECU) *d to Headlight ECU Sub-assembly LH
(for LED Headlight)
*e to Air Conditioning Amplifier Assembly *f to Certification ECU (Smart Key ECU Assembly)
(w/ Entry and Start System)
*g to Central Gateway ECU (Network Gateway ECU) *h to Telematics Transceiver
(w/ Manual (SOS) Switch)
*i to Radio and Display Receiver Assembly
(for Radio and Display Type)
- -



ii.

Check the connection diagram of the components which are connected to the No. 3 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F114-1 (CANH) V Combination meter assembly
(for Bus 5)
F114-12 (CANL) SB
F114-2 (CANH) G Main body ECU (multiplex network body ECU)
(for Bus 5)
F114-13 (CANL) SB
F114-3 (CANH) L Headlight ECU sub-assembly LH*1
(for Bus 5)
F114-14 (CANL) SB
F114-4 (CANH) P Air conditioning amplifier assembly
(for Bus 5)
F114-15 (CANL) SB
F114-5 (CANH) R Certification ECU (smart key ECU assembly)*2
(for Bus 5)
F114-16 (CANL) SB
F114-6 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 5)
F114-17 (CANL) SB
F114-8 (CANH) GR Telematics transceiver*3
(for Bus 3)
F114-19 (CANL) LG
F114-9 (CANH) B Radio and display receiver assembly*4
(for Bus 3)
F114-20 (CANL) LG
F114-10 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 3)
F114-21 (CANL) LG
F114-11 (CANH) V Central gateway ECU (network gateway ECU)
(for Bus 3)
F114-22 (CANL) LG

*1: for LED Headlight

*2: w/ Entry and Start System

*3: w/ Manual (SOS) Switch

*4: for Radio and Display Type





NO. 4 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C366168C25
3.333,1.083 3.833,1.333 0.5,0.25 2.417,2.333 2.927,2.063 true 4.625,0.656 3.49,1.844 true 3.604,1.844 4.656,0.927 true 3.323,2.063 2.417,3.167 true 3.479,2.052 4.667,3.479 true 2.417,1.667 2.917,1.844 true 2.417,1.25 3.177,1.844 true 2.417,2.75 3.177,2.063 true 2.417,0.833 3.302,1.833 true 3.615,2.052 4.656,3.094 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.844,1.083 2.438,1.271 0.594,0.188 10 false CANH*c 1.833,0.677 2.417,0.865 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F115 1.854,2.302 2.417,2.49 0.563,0.188 10 false CANL*b 1.854,2.708 2.417,2.906 0.563,0.198 10 false CANL*c 1.865,3.177 2.427,3.365 0.563,0.188 10 false CANL*d 4.719,0.521 5.302,0.708 0.583,0.188 10 false CANH*e 4.74,0.813 5.323,1 0.583,0.188 10 false CANH*f 4.74,3.073 5.292,3.271 0.552,0.198 10 false CANL*f 4.75,3.469 5.302,3.667 0.552,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Power Steering ECU Assembly *d to 4WD ECU Assembly
(for AWD)
*e to Steering Sensor *f to No. 5 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F115-1 (CANH) B Airbag sensor assembly
(for Bus 4)
F115-12 (CANL) W
F115-3 (CANH) P Power steering ECU assembly
(for Bus 4)
F115-14 (CANL) W
F115-4 (CANH) L 4WD ECU assembly*1
(for Bus 4)
F115-15 (CANL) W
F115-5 (CANH) BE Steering sensor
(for Bus 4)
F115-16 (CANL) W
F115-6 (CANH) GR No. 5 CAN junction connector
(for Bus 4)
F115-17 (CANL) W

*1: for AWD





NO. 5 CAN JUNCTION CONNECTOR (for RHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C366168C26
3.333,1.083 3.833,1.333 0.5,0.25 2.5,1.667 2.917,1.885 true 2.427,1.25 3.052,1.844 true 3.729,1.854 4.667,1.167 true 2.5,2.25 2.917,2.021 true 3.042,2.063 2.417,2.667 true 3.719,2.063 4.667,2.667 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.917,1.521 2.833,1.719 0.917,0.198 10 false CANH*b 1.865,1.063 2.781,1.26 0.917,0.198 10 false CANH*c 4.729,1.01 5.646,1.208 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F117 1.938,2.219 2.854,2.417 0.917,0.198 10 false CANL*b 1.865,2.635 2.781,2.833 0.917,0.198 10 false CANL*c 4.729,2.604 5.646,2.802 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Brake Actuator Assembly



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F117-1 (CANH) GR No. 4 CAN junction connector
(for Bus 4)
F117-12 (CANL) W
F117-2 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 4)
F117-13 (CANL) W
F117-7 (CANH) LG Brake actuator assembly
(for Bus 4)
F117-18 (CANL) W




NO. 4 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 4 CAN junction connector.

i.

Connection diagram

C366168C27
3.333,1.083 3.833,1.333 0.5,0.25 2.5,1.667 2.927,1.854 true 2.583,1.167 3.417,1.844 true 3.604,1.844 4.583,1.167 true 2.5,2.25 2.917,2.063 true 3.417,2.063 2.583,2.833 true 3.604,2.063 4.583,2.833 true 3.729,1.844 4.667,1.583 true 3.74,2.063 4.667,2.333 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.917,1.531 2.833,1.729 0.917,0.198 10 false CANH*b 2.01,1 2.927,1.198 0.917,0.198 10 false CANH*c 4.646,1.01 5.563,1.208 0.917,0.198 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F123 1.948,2.219 2.865,2.417 0.917,0.198 10 false CANL*b 2.031,2.833 2.948,3.031 0.917,0.198 10 false CANL*c 4.646,2.813 5.563,3.01 0.917,0.198 10 false CANL*d 4.729,1.469 5.646,1.667 0.917,0.198 10 false CANH*e 4.729,2.292 5.646,2.49 0.917,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to Airbag Sensor Assembly
*c to Steering Sensor *d to Power Steering ECU Assembly
*e to No. 5 CAN Junction Connector - -



ii.

Check the connection diagram of the components which are connected to the No. 4 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F123-1 (CANH) B Airbag sensor assembly
(for Bus 4)
F123-12 (CANL) W
F123-5 (CANH) BE Steering sensor
(for Bus 4)
F123-16 (CANL) W
F123-6 (CANH) P Power steering ECU assembly
(for Bus 4)
F123-17 (CANL) W
F123-7 (CANH) GR No. 5 CAN junction connector
(for Bus 4)
F123-18 (CANL) W




NO. 5 CAN JUNCTION CONNECTOR (for LHD)


a.

Check the No. 5 CAN junction connector.

i.

Connection diagram

C366168C28
3.333,1.083 3.833,1.333 0.5,0.25 3.615,1.854 4.583,0.667 true 3.615,2.052 4.5,3.25 true 2.917,1.844 2.417,1.667 true 3.417,1.854 2.333,0.833 true 3.042,1.854 2.333,1.25 true 3.063,2.063 2.333,2.75 true 2.917,2.063 2.417,2.333 true 3.417,2.073 2.333,3.167 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.833,1.531 2.427,1.729 0.594,0.198 10 false CANH*b 1.771,1.073 2.365,1.26 0.594,0.188 10 false CANH*c 1.76,0.698 2.344,0.885 0.583,0.188 10 false CANH*d 3.427,1.125 4.042,1.323 0.615,0.198 10 false F124 1.854,2.281 2.417,2.469 0.563,0.188 10 false CANL*b 1.792,2.698 2.354,2.896 0.563,0.198 10 false CANL*c 1.771,3.135 2.333,3.323 0.563,0.188 10 false CANL*d 4.656,0.542 5.24,0.729 0.583,0.188 10 false CANH*e 4.573,3.25 5.135,3.438 0.563,0.188 10 false CANL*e
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Central Gateway ECU (Network Gateway ECU) *d to Brake Actuator Assembly
*e to 4WD ECU Assembly
(for AWD)
- -



ii.

Check the connection diagram of the components which are connected to the No. 5 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
F124-1 (CANH) GR No. 4 CAN junction connector
(for Bus 4)
F124-12 (CANL) W
F124-2 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 4)
F124-13 (CANL) W
F124-5 (CANH) LG Brake actuator assembly
(for Bus 4)
F124-16 (CANL) W
F124-6 (CANH) L 4WD ECU assembly*1
(for Bus 4)
F124-17 (CANL) W

*1: for AWD





NO. 6 CAN JUNCTION CONNECTOR (w/ Blind Spot Monitor System)


a.

Check the No. 6 CAN junction connector.

i.

Connection diagram

C366168C09
3.333,1.083 3.833,1.333 0.5,0.25 2.604,1.25 3.531,1.844 true 2.5,1.729 2.927,1.844 true 4.229,1.844 4.573,1.74 true 3.552,2.073 2.656,2.542 true 2.927,2.063 2.51,2.125 true 4.229,2.073 4.583,2.188 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.938,1.615 2.854,1.813 0.917,0.198 10 false CANH*b 2.01,1.125 2.927,1.323 0.917,0.198 10 false CANH*c 4.656,1.656 5.573,1.854 0.917,0.198 10 false CANH*d 3.469,1.125 4.083,1.323 0.615,0.198 10 false M92 1.958,2.063 2.875,2.26 0.917,0.198 10 false CANL*b 2.094,2.479 3.01,2.677 0.917,0.198 10 false CANL*c 4.677,2.125 5.594,2.323 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to Blind Spot Monitor Sensor LH *d to No. 1 CAN Junction Connector



ii.

Check the connection diagram of the components which are connected to the No. 6 CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
M92-1 (CANH) R Central gateway ECU (network gateway ECU)
(for Bus 1)
M92-12 (CANL) GR
M92-6 (CANH) G Blind spot monitor sensor LH
(for Bus 1)
M92-17 (CANL) GR
M92-11 (CANH) B No. 1 CAN junction connector
(for Bus 1)
M92-22 (CANL) GR




DLC3


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C349818C06
1.625,1.313 2.042,1.583 0.417,0.271 4.469,2 4.281,1.698 true 3.458,1.125 3.198,0.76 true 4.25,0.708 3.906,1.115 true 3.823,1.698 3.646,2.063 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *1 4.302,0.604 4.938,0.833 0.635,0.229 10 false CANH 3.313,2.083 3.948,2.313 0.635,0.229 10 false CANL 2.958,0.646 3.594,0.875 0.635,0.229 10 false CG 4.5,2.042 5.135,2.271 0.635,0.229 10 false BAT 1.729,1.396 2.365,1.625 0.635,0.229 10 false F41
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F41-6 (CANH) - F41-14 (CANL) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F41-6 (CANH) - F41-4 (CG) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F41-14 (CANL) - F41-4 (CG) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F41-6 (CANH) - F41-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F41-14 (CANL) - F41-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C349819C17
1.083,1.281 1.5,1.552 0.417,0.271 2.969,1.302 2.198,0.885 true 3.052,1.302 2.198,0.635 true 3.135,1.292 2.188,0.438 true 3.25,1.292 2.208,0.188 true 4.563,0.885 3.938,1.302 true 4.563,0.281 3.563,1.375 true 4.552,0.583 3.646,1.375 true 4.698,1.99 3.896,1.427 true 4.708,2.208 3.792,1.427 true 4.719,2.375 3.719,1.438 true 2.917,1.427 2.25,1.948 true 3.031,1.427 2.302,2.167 true 3.177,1.427 2.302,2.375 true 3.271,1.427 2.313,2.604 true 4.26,2.51 3.448,1.427 true 3.75,2.542 3.365,1.417 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.885,2.125 2.375,2.302 0.49,0.177 10 false CA1H 1.792,0.563 2.344,0.781 0.552,0.219 10 false CA1L 1.792,0.354 2.344,0.573 0.552,0.219 10 false CA2L 1.896,2.323 2.385,2.5 0.49,0.177 10 false CA2H 1.792,0.115 2.281,0.292 0.49,0.177 10 false CA3H 1.938,2.573 2.49,2.792 0.552,0.219 10 false CA3L 1.885,1.885 2.375,2.063 0.49,0.177 10 false CAXL 4.25,2.542 4.74,2.719 0.49,0.177 10 false CAYH 3.708,2.563 4.198,2.74 0.49,0.177 10 false CAYL 4.615,0.188 5.104,0.365 0.49,0.177 10 false CA4H 4.771,2.125 5.26,2.302 0.49,0.177 10 false CA5H 4.792,2.313 5.344,2.531 0.552,0.219 10 false CA5L 1.188,1.344 1.635,1.604 0.448,0.26 10 false F74 4.76,1.938 5.25,2.115 0.49,0.177 10 false CA6H 4.615,0.469 5.167,0.688 0.552,0.219 10 false CA4L 1.771,0.802 2.26,0.979 0.49,0.177 10 false CAXH 4.625,0.781 5.177,1 0.552,0.219 10 false CA6L
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C348860C05
1.417,1.333 1.917,1.583 0.5,0.25 2.344,1.26 1.896,1.104 true 2.99,1.271 1.906,0.833 true 3.083,1.552 1.823,2.073 true 3.219,1.542 1.792,2.323 true 3.344,1.542 1.781,2.552 true 5.188,1.115 4.813,1.271 true 5.198,0.896 4.656,1.26 true 5.219,0.667 4.469,1.26 true 5.198,0.448 4.271,1.26 true 5.177,0.198 4.146,1.281 true 5.208,1.719 4.75,1.542 true 5.24,1.917 4.573,1.552 true 5.219,2.125 4.188,1.552 true 5.135,2.302 4.052,1.552 true 5.115,2.51 3.917,1.542 true 4.552,2.406 3.781,1.542 true 3.656,1.552 4.052,2.354 true 3.49,1.542 2.521,2.438 true 0.188,0.167 0.5,0.323 0.313,0.156 10 false *a 1.542,1.375 2.042,1.542 0.5,0.167 10 false F74 5.26,1.031 5.76,1.198 0.5,0.167 10 false GND 5.281,1.625 5.781,1.792 0.5,0.167 10 false CAXL 5.292,1.854 5.792,2.021 0.5,0.167 10 false CA1H 5.271,2.073 5.771,2.24 0.5,0.167 10 false CA2H 5.198,2.271 5.698,2.438 0.5,0.167 10 false CA3L 5.188,2.427 5.688,2.594 0.5,0.167 10 false CAYL 4.552,2.448 5.052,2.615 0.5,0.167 10 false CAYH 4.021,2.385 4.521,2.552 0.5,0.167 10 false CA4H 2.208,2.448 2.708,2.615 0.5,0.167 10 false CA4L 1.521,1 2.021,1.167 0.5,0.167 10 false BATT 1.521,0.719 2.021,0.885 0.5,0.167 10 false CA6L 1.406,2 1.906,2.167 0.5,0.167 10 false CA6H 1.396,2.24 1.896,2.406 0.5,0.167 10 false CA5H 1.396,2.479 1.896,2.646 0.5,0.167 10 false CA5L 5.26,0.802 5.76,0.969 0.5,0.167 10 false CAXH 5.271,0.573 5.771,0.74 0.5,0.167 10 false CA1L 5.271,0.344 5.771,0.51 0.5,0.167 10 false CA2L 5.271,0.094 5.771,0.26 0.5,0.167 10 false CA3H
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-14 (CA6H) - F74-5 (CA6L) R - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 1 MΩ or higher
F74-14 (CA6H) - F74-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-5 (CA6L) - F74-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-14 (CA6H) - F74-1 (BATT) R - Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F74-5 (CA6L) - F74-1 (BATT) W - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-23 (CA1H) - F74-9 (CAXH) R - P HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
F74-8 (CA1L) - F74-24 (CAXL) GR - GR LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
F74-23 (CA1H) - F74-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-8 (CA1L) - F74-10 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-23 (CA1H) - F74-1 (BATT) R - Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F74-8 (CA1L) - F74-1 (BATT) GR - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition

*1: w/ Stop and Start System

*2: w/o Stop and Start System

F74-18 (CA4H) - F74-17 (CA4L) W - P*1
R - P*2
HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F74-18 (CA4H) - F74-10 (GND) W - W-B*1
R - W-B*2
HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-17 (CA4L) - F74-10 (GND) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-18 (CA4H) - F74-1 (BATT) W - Y*1
R - Y*2
HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F74-17 (CA4L) - F74-1 (BATT) P - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-6 (CA3H) - F74-19 (CAYH) G - V HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
F74-21 (CA3L) - F74-20 (CAYL) LG - LG LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal Below 1 Ω
F74-6 (CA3H) - F74-10 (GND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-21 (CA3L) - F74-10 (GND) LG - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-6 (CA3H) - F74-1 (BATT) G - Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F74-21 (CA3L) - F74-1 (BATT) LG - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-22 (CA2H) - F74-7 (CA2L) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F74-22 (CA2H) - F74-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-7 (CA2L) - F74-10 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-22 (CA2H) - F74-1 (BATT) B - Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F74-7 (CA2L) - F74-1 (BATT) W - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F74-15 (CA5H) - F74-16 (CA5L) B - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F74-15 (CA5H) - F74-10 (GND) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-16 (CA5L) - F74-10 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F74-15 (CA5H) - F74-1 (BATT) B - Y HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F74-16 (CA5L) - F74-1 (BATT) SB - Y LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




STEERING SENSOR


C349821C04
4.385,0.406 4.802,0.667 0.417,0.26 4.438,2.167 4.604,1.667 true 5,2.167 4.75,1.677 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 4.49,0.479 4.948,0.677 0.458,0.198 10 false F69 5,2.198 5.583,2.448 0.583,0.25 10 false CANL 4.083,2.198 4.667,2.448 0.583,0.25 10 false CANH
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F69 steering sensor connector.


c.
C366202C01
1.458,0.333 1.958,0.583 0.5,0.25 2.104,1.354 2.417,1.583 true 1.031,1.917 1.677,1.344 true 0.958,1.688 1.51,1.354 true 1.01,1.479 1.333,1.354 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.573,0.385 1.885,0.583 0.313,0.198 10 false F69 0.594,1.667 1.156,1.833 0.563,0.167 10 false CANL 0.656,1.427 1.219,1.594 0.563,0.167 10 false ESS 0.615,1.917 1.177,2.083 0.563,0.167 10 false CANH 2.438,1.615 3,1.781 0.563,0.167 10 false BAT
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F69-3 (CANH) - F69-2 (CANL) BE - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F69-3 (CANH) - F69-1 (ESS) BE - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F69-2 (CANL) - F69-1 (ESS) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F69-3 (CANH) - F69-5 (BAT) BE - P HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F69-2 (CANL) - F69-5 (BAT) W - P LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 8NR-FTS)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A38 and C62 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C349827C11
1.229,0.313 1.625,0.563 0.396,0.25 4.417,0.271 4.823,0.49 0.406,0.219 2.125,1.24 2.333,0.583 true 2.135,1.365 2.385,2.281 true 0.865,1.24 0.615,0.49 true 5.417,1.406 6.583,0.583 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 4.51,0.323 4.823,0.521 0.313,0.198 10 false C62 1.323,0.375 1.635,0.573 0.313,0.198 10 false A38 2.396,0.5 3.021,0.708 0.625,0.208 10 false CANH 2.354,2.313 2.979,2.521 0.625,0.208 10 false CANL 0.24,0.354 0.865,0.563 0.625,0.208 10 false BATT 6.656,0.469 6.958,0.677 0.302,0.208 10 false E1
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-13 (CANH) - A38-26 (CANL) R - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A38-13 (CANH) - C62-53 (E1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-26 (CANL) - C62-53 (E1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-13 (CANH) - A38-1 (BATT) R - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A38-26 (CANL) - A38-1 (BATT) P - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ECM (for 3ZR-FAE)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A38 and C63 ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

C366217C01
1.167,0.333 1.667,0.583 0.5,0.25 4.417,0.333 4.917,0.583 0.5,0.25 0.573,0.583 0.854,1.271 true 2.125,1.375 2.552,2.302 true 2.135,1.24 2.5,0.552 true 6.021,1.385 6.448,0.542 true 0.156,0.083 0.469,0.24 0.313,0.156 10 false *a 0.188,0.49 0.594,0.677 0.406,0.188 10 false BATT 2.552,0.458 2.958,0.646 0.406,0.188 10 false CANH 2.396,2.323 2.802,2.51 0.406,0.188 10 false CANL 6.51,0.438 6.917,0.625 0.406,0.188 10 false E1 4.563,0.365 4.969,0.552 0.406,0.188 10 false C63 1.302,0.365 1.708,0.552 0.406,0.188 10 false A38
*a Front view of wire harness connector
(to ECM)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-13 (CANH) - A38-26 (CANL) R - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A38-13 (CANH) - C63-59 (E1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-26 (CANL) - C63-59 (E1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A38-13 (CANH) - A38-1 (BATT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A38-26 (CANL) - A38-1 (BATT) P - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F4 combination meter assembly connector.


c.
C328874C20
1.417,0.25 1.917,0.5 0.5,0.25 0.656,1.75 0.417,1.354 true 2.167,1.75 1.948,1.344 true 2.917,1.75 3.021,1.333 true 1.667,1.75 1.75,1.344 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.583,0.281 1.896,0.479 0.313,0.198 10 false F4 0.688,1.75 1,1.948 0.313,0.198 10 false ET 1.375,1.781 1.875,1.948 0.5,0.167 10 false CANL 2.125,1.781 2.625,1.948 0.5,0.167 10 false CANH 2.865,1.792 3.031,1.958 0.167,0.167 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F4-32 (CANH) - F4-31 (CANL) V - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F4-32 (CANH) - F4-21 (ET) V - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F4-31 (CANL) - F4-21 (ET) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F4-32 (CANH) - F4-40 (B) V - SB HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F4-31 (CANL) - F4-40 (B) SB - SB LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A42 brake actuator assembly connector.


c.
C366214C03
1.458,0.75 1.958,1 0.5,0.25 0.771,2.708 1.375,1.75 true 2.146,2.708 1.448,1.927 true 0.615,1.615 0.417,0.917 true 2.75,1.604 2.917,0.875 true 0.135,0.073 0.448,0.229 0.313,0.156 10 false *a 0.583,2.719 1.208,2.938 0.625,0.219 10 false CANL 1.99,2.719 2.615,2.938 0.625,0.219 10 false CANH 1.583,0.771 1.896,0.927 0.313,0.156 10 false A42 0.125,0.74 0.75,0.958 0.625,0.219 10 false +BS 2.948,0.698 3.396,0.896 0.448,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A42-5 (CANH) - A42-19 (CANL) LG - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A42-5 (CANH) - A42-46 (GND1) LG - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A42-19 (CANL) - A42-46 (GND1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A42-5 (CANH) - A42-30 (+BS) LG - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A42-19 (CANL) - A42-30 (+BS) W - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F15 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C350877C04
4.948,0.146 5.333,0.406 0.385,0.26 1.75,0.115 2.135,0.375 0.385,0.26 5.094,1.104 4.917,0.75 true 2.26,1.365 2.833,0.75 true 2.146,1.365 2.75,0.417 true 6.083,1.917 5.875,1.667 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 4.677,0.594 4.99,0.792 0.313,0.198 10 false CG 6.073,1.958 6.385,2.156 0.313,0.198 10 false BAT 5.021,0.219 5.333,0.417 0.313,0.198 10 false F41 1.823,0.167 2.135,0.365 0.313,0.198 10 false F15 2.927,0.646 3.531,0.896 0.604,0.25 10 false CANH 2.813,0.302 3.417,0.552 0.604,0.25 10 false CANL 3.75,0.073 4.063,0.271 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F15-14 (CANH) - F15-13 (CANL) G - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F15-14 (CANH) - F41-4 (CG) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F15-13 (CANL) - F41-4 (CG) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F15-14 (CANH) - F41-16 (BAT) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F15-13 (CANL) - F41-16 (BAT) SB - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F1 certification ECU (smart key ECU assembly) connector.


c.
C366211C01
1.417,0.417 1.917,0.667 0.5,0.25 1.083,1.448 0.667,0.865 true 0.51,1.5 0.896,1.5 true 0.448,2.573 0.865,1.99 true 2.542,1.458 3.042,0.958 true 1.583,0.438 1.896,0.635 0.313,0.198 10 false F1 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 0.24,0.76 0.719,1.042 0.479,0.281 10 false CANL 0.063,1.406 0.542,1.688 0.479,0.281 10 false CANH 0.323,2.563 0.635,2.76 0.313,0.198 10 false E 3.104,0.865 3.417,1.063 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F1-1 (CANH) - F1-2 (CANL) R - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F1-1 (CANH) - F1-18 (E) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F1-2 (CANL) - F1-18 (E) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F1-1 (CANH) - F1-4 (+B) R - L HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F1-2 (CANL) - F1-4 (+B) SB - L LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F23 and F68 power steering ECU assembly connectors.


c.
C328899C08
0.417,1.25 0.917,1.5 0.5,0.25 0.417,3.167 0.917,3.417 0.5,0.25 1.167,2 1.333,1.5 true 2.333,2 2.083,1.5 true 1.5,4.083 1.75,3.448 true 2.333,4.083 2.01,3.438 true 0.542,3.198 1,3.396 0.458,0.198 10 false F23 0.531,1.292 0.99,1.49 0.458,0.198 10 false F68 0.979,2.031 1.438,2.229 0.458,0.198 10 false PIG 2.313,2.031 2.938,2.229 0.625,0.198 10 false PGND 2.313,4.125 2.938,4.323 0.625,0.198 10 false CANL 1.198,4.135 1.823,4.333 0.625,0.198 10 false CANH 0.208,0.135 0.667,0.333 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F23-7 (CANH) - F23-8 (CANL) P - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F23-7 (CANH) - F68-2 (PGND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F23-8 (CANL) - F68-2 (PGND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F23-7 (CANH) - F68-1 (PIG) P - B-W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F23-8 (CANL) - F68-1 (PIG) W - B-W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F38 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C366206C01
1.583,0.583 2.083,0.833 0.5,0.25 5.167,0.583 5.667,0.833 0.5,0.25 1,1.333 1.385,1.469 true 1.021,1.021 1.635,1.469 true 1.063,1.948 1.521,1.625 true 6.156,1.729 6.354,2.042 true 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.698,0.615 2.01,0.813 0.313,0.198 10 false F38 5.292,0.615 5.604,0.813 0.313,0.198 10 false F41 6.365,2.094 6.781,2.302 0.417,0.208 10 false BAT 0.813,0.906 1.229,1.115 0.417,0.208 10 false R1 0.833,1.25 1.25,1.458 0.417,0.208 10 false E 0.875,1.969 1.292,2.177 0.417,0.208 10 false R2 3.906,0.115 4.219,0.313 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F38-3 (R1) - F38-10 (R2) SB - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F38-3 (R1) - F38-1 (E) SB - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F38-10 (R2) - F38-1 (E) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F38-3 (R1) - F41-16 (BAT) SB - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F38-10 (R2) - F41-16 (BAT) GR - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F70 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350880C03
1.698,0.094 2.073,0.323 0.375,0.229 5.094,0.375 5.469,0.604 0.375,0.229 6.167,2.083 5.938,1.667 true 1.49,1.281 1.24,0.531 true 1.25,2.333 1.333,1.792 true 1.917,2.333 1.802,1.781 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.76,0.094 4.073,0.292 0.313,0.198 10 false *1 1.771,0.135 2.083,0.333 0.313,0.198 10 false F70 0.813,0.427 1.302,0.656 0.49,0.229 10 false CANH 0.948,2.375 1.438,2.604 0.49,0.229 10 false CANL 1.906,2.385 2.396,2.615 0.49,0.229 10 false E1 5.167,0.406 5.479,0.604 0.313,0.198 10 false F41 6.146,2.135 6.635,2.365 0.49,0.229 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F70-13 (CANH) - F70-22 (CANL) B - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 108 to 132 Ω
F70-13 (CANH) - F70-25 (E1) B - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F70-22 (CANL) - F70-25 (E1) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F70-13 (CANH) - F41-16 (BAT) B - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F70-22 (CANL) - F41-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Top-mounted Air Conditioner Pressure Sensor)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F72 air conditioning amplifier assembly connector.


c.
E281476C45
1.448,0.167 1.948,0.417 0.5,0.25 0.917,1.75 1.469,1.188 true 2.313,1.75 1.656,1.188 true 0.25,1.75 0.344,1.188 true 1.667,1.75 1.5,1.354 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 1.573,0.229 1.885,0.427 0.313,0.198 10 false F72 0.688,1.802 1.125,2.021 0.438,0.219 10 false CANH 2.188,1.781 2.625,2 0.438,0.219 10 false CANL 0.177,1.792 0.333,1.99 0.156,0.198 10 false B 1.563,1.781 2,2 0.438,0.219 10 false GND
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F72-9 (CANH) - F72-10 (CANL) P - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F72-9 (CANH) - F72-29 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F72-10 (CANL) - F72-29 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F72-9 (CANH) - F72-1 (B) P - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F72-10 (CANL) - F72-1 (B) SB - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY (w/ Side-mounted Air Conditioner Pressure Sensor)


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F73 air conditioning amplifier assembly connector.


c.
C349836C14
1.5,0.208 1.917,0.479 0.417,0.271 0.781,1.604 0.5,1.25 true 1.865,1.833 1.5,1 true 2.031,1.833 2.25,1 true 2.656,1.594 2.833,1.167 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.604,0.281 1.917,0.479 0.313,0.198 10 false F73 1.073,0.896 1.74,1.104 0.667,0.208 10 false CANH 2.333,0.885 3,1.094 0.667,0.208 10 false CANL 2.927,1.073 3.396,1.302 0.469,0.229 10 false GND 0.365,1.094 0.833,1.323 0.469,0.229 10 false B
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F73-11 (CANH) - F73-12 (CANL) P - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F73-11 (CANH) - F73-4 (GND) P - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F73-12 (CANL) - F73-4 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F73-11 (CANH) - F73-1 (B) P - V HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F73-12 (CANL) - F73-1 (B) SB - V LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the F125 and F126 radio and display receiver assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C366204C01
1.5,0.5 2,0.75 0.5,0.25 4.927,0.667 5.427,0.917 0.5,0.25 2.052,1.313 2.833,0.5 true 2.188,1.323 2.917,0.75 true 4.667,1.917 5.052,1.531 true 5.563,1.229 5.917,1 true 0.167,0.083 0.479,0.281 0.313,0.198 10 false *a 5.031,0.698 5.594,0.865 0.563,0.167 10 false F126 1.604,0.531 2.167,0.698 0.563,0.167 10 false F125 6.021,0.906 6.583,1.073 0.563,0.167 10 false +B1 4.333,1.969 4.896,2.135 0.563,0.167 10 false GND1 2.99,0.677 3.552,0.844 0.563,0.167 10 false CANL 2.917,0.417 3.479,0.583 0.563,0.167 10 false CANH
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F125-9 (CANH) - F125-10 (CANL) B - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F125-9 (CANH) - F126-7 (GND1) B - LA HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F125-10 (CANL) - F126-7 (GND1) LG - LA LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F125-9 (CANH) - F126-4 (+B1) B - LA-SB*1
B - SB*2
HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F125-10 (CANL) - F126-4 (+B1) LG - LA-SB*1
LG - SB*2, *3
LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher


*1: w/ Top-mounted Air Conditioner Pressure Sensor without Stop and Start System

*2: w/ Side-mounted Air Conditioner Pressure Sensor

*3: w/ Stop and Start System




HEADLIGHT ECU SUB-ASSEMBLY LH (for LED Headlight)


Refer to Terminals of ECU.

Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A16 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C366205C04
1.594,0.417 2.094,0.667 0.5,0.25 5.25,0.583 5.75,0.833 0.5,0.25 0.594,2.146 0.844,1.635 true 2.406,2.188 2.635,1.677 true 3.125,2.146 2.813,1.688 true 6.354,1.969 6.167,1.74 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.719,0.438 2.115,0.604 0.396,0.167 10 false A16 5.385,0.615 5.781,0.781 0.396,0.167 10 false F41 0.365,2.177 0.76,2.344 0.396,0.167 10 false GND 2.135,2.208 2.698,2.375 0.563,0.167 10 false CANL 3.104,2.188 3.667,2.354 0.563,0.167 10 false CANH 6.375,2.021 6.938,2.188 0.563,0.167 10 false BAT 4.26,0.125 4.573,0.323 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A16-24 (CANH) - A16-23 (CANL) L - SB HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A16-24 (CANH) - A16-12 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A16-23 (CANL) - A16-12 (GND) SB - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A16-24 (CANH) - F41-16 (BAT) L - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A16-23 (CANL) - F41-16 (BAT) SB- R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M62 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C350884C05
1.688,0.135 2.115,0.427 0.427,0.292 4.979,0.208 5.406,0.5 0.427,0.292 6.094,2.021 5.854,1.667 true 1.719,1.313 1.51,0.688 true 1.458,2.135 1.708,1.563 true 2.51,2.146 2.25,1.563 true 0.115,0.073 0.427,0.271 0.313,0.198 10 false *a 3.635,0.073 3.948,0.271 0.313,0.198 10 false *1 1.771,0.219 2.094,0.417 0.323,0.198 10 false M62 5.073,0.292 5.396,0.49 0.323,0.198 10 false F41 1.125,2.167 1.615,2.417 0.49,0.25 10 false CA1N 1.125,0.552 1.615,0.802 0.49,0.25 10 false CA1P 2.49,2.208 2.979,2.458 0.49,0.25 10 false BLGD 6.073,2.063 6.563,2.313 0.49,0.25 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M62-2 (CA1P) - M62-7 (CA1N) G - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
M62-2 (CA1P) - M62-10 (BLGD) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M62-7 (CA1N) - M62-10 (BLGD) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M62-2 (CA1P) - F41-16 (BAT) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M62-7 (CA1N) - F41-16 (BAT) GR - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>LANE DEPARTURE ALERT SYSTEM (w/ Steering Control)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the R5 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C350886C04
1.823,0.146 2.146,0.396 0.323,0.25 4.979,0.198 5.385,0.469 0.406,0.271 2.25,1.333 2.781,0.948 true 1.927,2.063 2.042,1.688 true 2.417,2.031 2.24,1.698 true 6.094,1.948 5.875,1.677 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 3.781,0.094 4.094,0.292 0.313,0.198 10 false *1 1.896,0.198 2.208,0.396 0.313,0.198 10 false R5 2.844,0.844 3.313,1.063 0.469,0.219 10 false CA1P 2.396,2.073 2.865,2.292 0.469,0.219 10 false CA1N 1.677,2.083 2.146,2.302 0.469,0.219 10 false GND 5.073,0.26 5.385,0.458 0.313,0.198 10 false F41 6.083,2 6.552,2.219 0.469,0.219 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
R5-5 (CA1P) - R5-11 (CA1N) R - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
R5-5 (CA1P) - R5-10 (GND) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R5-11 (CA1N) - R5-10 (GND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
R5-5 (CA1P) - F41-16 (BAT) R - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
R5-11 (CA1N) - F41-16 (BAT) GR - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the A2 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C350887C03
4.99,0.208 5.354,0.479 0.365,0.271 1.74,0.115 2.104,0.385 0.365,0.271 0.99,1.344 1.688,1.344 true 6.063,1.958 5.875,1.667 true 2.458,0.656 2.125,1.26 true 1.646,0.646 1.854,1.26 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 3.719,0.115 4.031,0.313 0.313,0.198 10 false *1 1.25,0.542 1.729,0.75 0.479,0.208 10 false CA2L 2.51,0.552 2.99,0.76 0.479,0.208 10 false CA2H 0.531,1.281 1.01,1.49 0.479,0.208 10 false SGND 6.073,1.99 6.552,2.198 0.479,0.208 10 false BAT 5.063,0.281 5.385,0.479 0.323,0.198 10 false F41 1.844,0.177 2.167,0.375 0.323,0.198 10 false A2
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A2-3 (CA2H) - A2-2 (CA2L) G - GR HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
A2-3 (CA2H) - A2-1 (SGND) G - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A2-2 (CA2L) - A2-1 (SGND) GR - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A2-3 (CA2H) - F41-16 (BAT) G - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A2-2 (CA2L) - F41-16 (BAT) GR - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




ENGINE STOP AND START ECU (w/ Stop and Start System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C323601C27
1.51,0.177 1.938,0.448 0.427,0.271 1.531,2.052 1.958,2.323 0.427,0.271 0.646,1.604 1.146,1.354 true 1.156,4.063 0.771,3.521 true 0.365,4.094 0.615,3.521 true 2.74,1.833 2.344,1.417 true 0.115,0.052 0.427,0.25 0.313,0.198 10 false *a 1.594,0.229 2.052,0.427 0.458,0.198 10 false A61 0.281,1.542 0.74,1.74 0.458,0.198 10 false BIN1 1.604,2.104 2.063,2.302 0.458,0.198 10 false F77 1.01,4.104 1.677,4.406 0.667,0.302 10 false CANL 0.156,4.125 0.76,4.365 0.604,0.24 10 false CANH 2.594,1.896 3.375,2.208 0.781,0.313 10 false GND1
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the A61 and F77 engine stop and start ECU connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F77-13 (CANH) - F77-14 (CANL) R - P HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F77-13 (CANH) - A61-8 (GND1) R - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F77-14 (CANL) - A61-8 (GND1) P - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F77-13 (CANH) - A61-3 (BIN1) R - B HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F77-14 (CANL) - A61-3 (BIN1) P - B LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




TELEMATICS TRANSCEIVER (w/ Manual (SOS) Switch)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.
C285245C29
1.5,0.083 1.917,0.333 0.417,0.25 2.417,1.917 2.01,1.219 true 1.417,1.917 1.844,1.219 true 2.427,0.917 2.917,0.25 true 0.49,0.906 0.75,0.25 true 0.052,0.042 0.385,0.302 0.333,0.26 10 false *a 2.26,1.969 2.875,2.167 0.615,0.198 10 false CANN 1.219,1.969 1.833,2.167 0.615,0.198 10 false CANP 1.594,0.146 2.063,0.396 0.469,0.25 10 false F51 0.792,0.083 1.177,0.406 0.385,0.323 10 false +B 2.969,0.094 3.24,0.385 0.271,0.292 10 false E
*a Front view of wire harness connector
(to Telematics Transceiver)


Disconnect the F51 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F51-15 (CANP) - F51-16 (CANN) GR - LG HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
F51-15 (CANP) - F51-4 (E) GR - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F51-16 (CANN) - F51-4 (E) LG - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
F51-15 (CANP) - F51-1 (+B) GR - W HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F51-16 (CANN) - F51-1 (+B) LG - W LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher




4WD ECU ASSEMBLY (for AWD)


Refer to Terminals of ECU.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the M77 4WD ECU assembly connector.

C346217C04
1.594,0.167 2.063,0.427 0.469,0.26 4.625,0.125 5.094,0.385 0.469,0.26 2.583,0.896 2.75,0.417 true 0.917,1.5 1.188,1.115 true 1.583,1.5 1.302,1.115 true 6.083,1.5 5.75,1.25 true 0.146,0.052 0.458,0.25 0.313,0.198 10 false *a 3.615,0.073 3.927,0.271 0.313,0.198 10 false *1 1.708,0.208 2.167,0.406 0.458,0.198 10 false M77 4.771,0.167 5.229,0.365 0.458,0.198 10 false F41 1.406,1.552 2.021,1.75 0.615,0.198 10 false CANH 0.667,1.542 1.281,1.74 0.615,0.198 10 false CANL 2.792,0.281 3.406,0.479 0.615,0.198 10 false GND 6.135,1.438 6.75,1.635 0.615,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to 4WD ECU Assembly)
- -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
M77-6 (CANH) - M77-5 (CANL) L - W HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) battery terminal 54 to 69 Ω
M77-6 (CANH) - M77-4 (GND) L - W-B HIGH-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M77-5 (CANL) - M77-4 (GND) W - W-B LOW-level CAN bus line - Ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
M77-6 (CANH) - F41-16 (BAT) L - R HIGH-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
M77-5 (CANL) - F41-16 (BAT) W - R LOW-level CAN bus line - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher