According to signals from the air conditioning amplifier assembly that are based on user operation or air conditioning system control, the blower motor damper servo sub-assembly (fresh/recirculation) actuates the servo motor to switch between inside and outside air intake.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1442 | Air Inlet Damper Control Servo Motor Circuit | Any of the following conditions is met:
·
No. 1 blower motor damper servo sub-assembly (fresh/recirculation) drive terminal is open circuit ·
No. 1 blower motor damper servo sub-assembly (fresh/recirculation) drive terminal is short circuit |
·
No. 1 blower motor damper servo sub-assembly (fresh/recirculation) ·
Air conditioning harness assembly (heater radiator unit sub-assembly) ·
Air conditioning harness assembly (blower assembly) ·
Air conditioning amplifier assembly |
Memorized
(30 seconds or more)* |
*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction Status | No. 1 blower motor damper servo sub-assembly (fresh/recirculation) drive terminal is open circuit | ○ | - |
| No. 1 blower motor damper servo sub-assembly (fresh/recirculation) drive terminal is short circuit | - | ○ | |
| Detection Time | 30 seconds or more | 30 seconds or more | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
When installing the damper servo motor, make sure to install it correctly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT (for VALEO Made)>REASSEMBLY
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Inlet | No. 1 blower damper servo sub-assembly (fresh/recirculation) | Min.: 0
Max.: 100 |
Operates between
0 to 100% |
| Tester Display |
|---|
| Air Inlet |
No. 1 blower motor damper servo sub-assembly (fresh/recirculation) operates normally.
| Result | Proceed to |
|---|---|
| NG (When troubleshooting according to Problem Symptoms Table) | A |
| NG (When troubleshooting according to the DTC) | B |
| OK (When troubleshooting according to Problem Symptoms Table) | C |
| OK (When troubleshooting according to the DTC) | D |
A
B
C
D
Check for a wire harness caught between the links of the motors and dampers.
No wire harnesses are caught between the links of the motors and dampers.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 blower damper servo sub-assembly (fresh/recirculation).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT (for VALEO Made)>DISASSEMBLY
Operate the dampers by hand.
The dampers are easily operated by hand.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning harness assembly (heater radiator unit sub-assembly).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for VALEO Made)>DISASSEMBLY
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
| *b | Front view of wire harness connector
(to Air Conditioning Harness Assembly (blower assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F7A-13 (BAI) - w-6 | Always | Below 1 Ω |
| F7A-9 (A1AI) - w-1 | Always | Below 1 Ω |
| F7A-3 (A2AI) - w-2 | Always | Below 1 Ω |
| F7A-10 (B1AI) - w-3 | Always | Below 1 Ω |
| F7A-2 (B2AI) - w-4 | Always | Below 1 Ω |
| F7A-13 (BAI) or w-6 - Body ground | Always | 10 kΩ or higher |
| F7A-9 (A1AI) or w-1 - Body ground | Always | 10 kΩ or higher |
| F7A-3 (A2AI) or w-2 - Body ground | Always | 10 kΩ or higher |
| F7A-10 (B1AI) or w-3 - Body ground | Always | 10 kΩ or higher |
| F7A-2 (B2AI) or w-4 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for VALEO Made)>DISASSEMBLY
Remove the air conditioning harness assembly (blower assembly).
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT (for VALEO Made)>DISASSEMBLY
| *a | Front view of wire harness connector
(from Air Conditioning Harness Assembly (Heater Radiator Unit Sub-assembly)) |
| *b | Front view of wire harness connector
(to No. 1 blower damper servo sub-assembly (fresh/recirculation)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| w-1 - AI-1 (A1AI) | Always | Below 1 Ω |
| w-6 - AI-2 (BAI) | Always | Below 1 Ω |
| w-2 - AI-3 (A2AI) | Always | Below 1 Ω |
| w-3 - AI-4 (B1AI) | Always | Below 1 Ω |
| w-4 - AI-6 (B2AI) | Always | Below 1 Ω |
| w-1 or AI-1 (A1AI) - Body ground | Always | 10 kΩ or higher |
| w-6 or AI-2 (BAI) - Body ground | Always | 10 kΩ or higher |
| w-2 or AI-3 (A2AI) - Body ground | Always | 10 kΩ or higher |
| w-3 or AI-4 (B1AI) - Body ground | Always | 10 kΩ or higher |
| w-4 or AI-6 (B2AI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the No. 1 blower damper servo sub-assembly (fresh/recirculation) with a new one or the No. 2 air conditioning radiator damper servo sub-assembly (mode switching) if it is functioning properly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT (for VALEO Made)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Air Inlet | No. 1 blower damper servo sub-assembly (fresh/recirculation) | Min.: 0
Max.: 100 |
Operates between
0 to 100% |
| Tester Display |
|---|
| Air Inlet |
No. 1 blower motor damper servo sub-assembly (fresh/recirculation) operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B