The main body ECU (multiplex network body ECU) controls the operation of the following lights:
Map Light Assembly
No. 1 Room Light Assembly
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin*1.
*1: w/ Entry and Start System
The DOME CUT relay supplies power to the interior lights. If all the lights that use power from the DOME CUT relay do not turn on, check the interior light auto cut circuit first.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>Interior Light Auto Cut Circuit
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Illuminated Entry System | Turns on the lights that are controlled by the illuminated entry system.* | ON or OFF | - |
*: Refer to System Description for the lights that are controlled by the illuminated entry system.
Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>SYSTEM DESCRIPTION
| Tester Display |
|---|
| Illuminated Entry System |
All lights that are controlled by the illuminated entry system come on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Inspect the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R2-12(+B1) - R2-4 (RLMP) | No. 1 room light switch in DOOR position | Below 1 Ω |
| No. 1 room light switch in ON position | 10 kΩ or higher | |
| R2-12 (+B1) or R2-4 (RLMP) - Body ground | No. 1 room light switch in DOOR position | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R2-12 (+B1) - Body ground | Battery saving function not operating | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R2-10 (DOOR) - 3D-29 | Always | Below 1 Ω |
| R2-10 (DOOR) or 3D-29 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-29 - MB-1 (ILE) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
A
B
C
D