Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2019.09–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P036511  Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground  P036515  Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open  P03652A  Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range  P036531  Camshaft Position Sensor "B" Bank 1 No Signal  


DESCRIPTION

The camshaft position sensor (for the exhaust camshaft) (EV1 signal) consists of a magnet and MRE (Magneto Resistance Element).

The exhaust camshaft has a timing rotor for the camshaft position sensor. When the exhaust camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P036511 Camshaft Position Sensor "B" Bank 1 Circuit Short to Ground The camshaft position sensor (for exhaust camshaft) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored SAE Code:
P0367
P036515 Camshaft Position Sensor "B" Bank 1 Circuit Short to Battery or Open The camshaft position sensor (for exhaust camshaft) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

ECM


Comes on DTC stored SAE Code:
P0368
P03652A Camshaft Position Sensor "B" Bank 1 Signal Stuck in Range No camshaft position sensor (for exhaust camshaft) signal to ECM while engine cranking (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

Exhaust camshaft

·

Valve timing

·

ECM


Comes on DTC stored SAE Code:
P0365
P036531 Camshaft Position Sensor "B" Bank 1 No Signal No camshaft position sensor (for exhaust camshaft) signal for 5 seconds at an engine speed of 600 rpm or higher (1 trip detection logic).
·

Open or short in camshaft position sensor (for exhaust camshaft) circuit

·

Camshaft position sensor (for exhaust camshaft)

·

Exhaust camshaft

·

Valve timing

·

ECM


Comes on DTC stored SAE Code:
P0365

HINT:

Reference: Inspection using an oscilloscope.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P034011


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor (for exhaust camshaft) despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for 4 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Exhaust camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 seconds or more.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P036511, P036515, P03652A or P036531.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A395438E03
0.938,2.25 4.042,2.51 3.104,0.26 10 false Camshaft Position Sensor (for Exhaust Camshaft) 0.938,2.094 1.25,2.271 0.313,0.177 10 false W1 1.844,1.5 2.25,1.667 0.406,0.167 10 false VVE- 1.823,0.958 2.219,1.167 0.396,0.208 10 false VVE+ 1.906,0.417 2.219,0.594 0.313,0.177 10 false VC2 4.469,0.417 4.781,0.594 0.313,0.177 10 false 111 4.531,0.969 4.844,1.146 0.313,0.177 10 false 81 4.469,1.5 4.781,1.677 0.313,0.177 10 false 112 4.854,0.417 5.333,0.583 0.479,0.167 10 false VCE1 4.854,0.958 5.25,1.125 0.396,0.167 10 false EV1+ 4.854,1.49 5.25,1.667 0.396,0.177 10 false EV1- 5.615,0.313 5.948,0.479 0.333,0.167 10 false 5 V 2.302,0.417 2.615,0.594 0.313,0.177 10 false 3 2.302,0.958 2.615,1.135 0.313,0.177 10 false 1 2.323,1.5 2.635,1.677 0.313,0.177 10 false 2 5.323,2.375 5.823,2.625 0.5,0.25 10 false ECM 5.323,2.229 5.823,2.479 0.5,0.25 10 false C62

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
A384859C03
0.333,2.333 0.833,2.583 0.5,0.25 2.302,3.125 1.781,2.51 true 0.448,2.385 0.906,2.583 0.458,0.198 10 false W1 2.354,3.125 2.667,3.323 0.313,0.198 10 false VC2 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Camshaft Position Sensor (for Exhaust Camshaft))


a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W1-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)

NG

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
a.

Disconnect the W1 camshaft position sensor (for exhaust camshaft) connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W1-1 (VVE+) - C62-81 (EV1+) Always Below 1 Ω
W1-2 (VVE-) - C62-112 (EV1-) Always Below 1 Ω
W1-1 (VVE+) or C62-81 (EV1+) - Body ground and other terminals Always 10 kΩ or higher
W1-2 (VVE-) or C62-112 (EV1-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR FOR EXHAUST CAMSHAFT)
A384847C02
0.75,1.021 1.063,1.219 0.313,0.198 10 false *a 0.792,2.458 1.104,2.656 0.313,0.198 10 false *b 2.5,2.396 2.813,2.594 0.313,0.198 10 false *c
*a OK
*b NG
*c Clearance


a.

Check the camshaft position sensor (for exhaust camshaft) installation.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)

NG

4.INSPECT EXHAUST CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the exhaust camshaft.

OK:

Camshaft timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the exhaust camshaft.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

NG

5.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)
a.

Replace the camshaft position sensor (for exhaust camshaft).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>CAMSHAFT POSITION SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P036511, P036515, P03652A OR P036531)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P036511, P036515, P03652A OR P036531)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Read the DTCs.

Result:
Result Proceed to
DTC P036511, P036515, P03652A or P036531 is output A
DTCs are not output B


HINT:

If the engine does not start, replace the ECM.




A

7.CHECK ENGINE MECHANICAL SYSTEM

B

END

7.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY


Result:
Proceed to
OK
NG



OK

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P036511, P036515, P03652A OR P036531)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P036511, P036515, P03652A OR P036531)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Start the engine.


g.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Read the DTCs.

Result:
Result Proceed to
DTC P036511, P036515, P03652A or P036531 is output A
DTCs are not output B




A

B

9.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT) - ECM)
a.

Disconnect the W1 camshaft position sensor (for exhaust camshaft) connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W1-3 (VC2) - C62-111 (VCE1) Always Below 1 Ω
W1-3 (VC2) or C62-111 (VCE1) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR