Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P061512  Starter Relay Circuit Short to Battery  


DESCRIPTION


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P061512 Starter Relay Circuit Short to Battery All of the following conditions are met, and battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

ST relay

·

Starter signal circuit

·

Park/Neutral position switch*1

·

Clutch start switch assembly*2

·

Certification ECU (Smart Key ECU Assembly)*3

·

Ignition or starter switch assembly*4

·

ECM


Comes on DTC stored SAE Code: P0617

*1: for CVT

*2: for Manual Transaxle

*3: w/ Entry and Start System

*4: w/o Entry and Start System

MONITOR DESCRIPTION

If the ECM detects the starter control (STA) signal for 20 seconds or more while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12 mph) or more, it determines that there is a malfunction in the STA circuit, illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A231469E72
1.229,1.979 1.604,2.156 0.375,0.177 10 false Idling 0.438,2.25 1.833,2.583 1.396,0.333 10 false Ignition Switch ON 0.448,0.833 1.802,1.083 1.354,0.25 10 false 24 km/h (15 mph) 2.396,2.854 3.083,3.167 0.688,0.313 10 false 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 false 20 seconds or more 2,2.333 2.406,2.521 0.406,0.188 10 false [A] 2.583,2.125 2.792,2.302 0.208,0.177 10 false [B] 4.031,0.458 4.26,0.625 0.229,0.167 10 false [C] 4.906,3.344 5.135,3.51 0.229,0.167 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Start the engine.

9.

Idle the engine for 5 seconds or more [B].

10.

Drive the vehicle at a speed of 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P061512.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

for CVT


A384844E04
1.052,6.219 2.125,6.417 1.073,0.198 10 false Battery 0.76,1.365 1.375,1.563 0.615,0.198 10 false STAR 0.896,2.438 1.354,2.635 0.458,0.198 10 false STA 0.104,2.969 1.865,3.156 1.76,0.188 10 false Smart Key ECU Assembly 6.042,0.792 6.5,0.99 0.458,0.198 10 false STA 6.063,1.271 6.521,1.469 0.458,0.198 10 false NSW 3.75,2.094 4.698,2.813 0.948,0.719 10 false Park/Neutral Position Switch 0.167,0.094 2.885,0.354 2.719,0.26 12 false w/ Entry and Start System: 4.76,5.292 6.375,5.479 1.615,0.188 10 false Starter Assembly 6.302,3.667 6.76,3.865 0.458,0.198 10 false ECM 3.74,1.885 4.208,2.083 0.469,0.198 10 false C36 0.104,2.781 1.563,3 1.458,0.219 10 false M66 6.313,3.531 6.771,3.729 0.458,0.198 10 false A38 2.917,4.552 3.375,4.75 0.458,0.198 10 false ST 1.604,4.042 2.063,4.24 0.458,0.198 10 false ST 0.802,4.594 1.646,4.823 0.844,0.229 10 false BATT MAIN 4.344,5.333 4.802,5.531 0.458,0.198 10 false C67 5.354,4.771 5.813,4.969 0.458,0.198 10 false C34 5.365,5.01 5.823,5.208 0.458,0.198 10 false C35 4.438,5.125 4.594,5.323 0.156,0.198 10 false 1 5.167,4.729 5.323,4.927 0.156,0.198 10 false 1 5.167,4.979 5.323,5.177 0.156,0.198 10 false 1 5.74,4.74 6.052,4.938 0.313,0.198 10 false *1 5.74,5.01 6.052,5.208 0.313,0.198 10 false *2 1.531,6.896 3.365,7.094 1.833,0.198 10 false *1: TMC Made 1.542,7.229 2.771,7.427 1.229,0.198 10 false *2: TMMT Made 1.24,2.354 1.552,2.552 0.313,0.198 10 false 20 1.26,1.24 1.417,1.438 0.156,0.198 10 false 9 5.75,0.688 6.063,0.885 0.313,0.198 10 false 29 5.781,1.25 6.094,1.448 0.313,0.198 10 false 57 5.094,2.583 5.25,2.781 0.156,0.198 10 false 9 5.365,1.604 5.521,1.802 0.156,0.198 10 false 4 2.594,3.823 2.75,4.021 0.156,0.198 10 false 5 3.323,3.823 3.479,4.021 0.156,0.198 10 false 3 2.563,4.188 2.719,4.385 0.156,0.198 10 false 1 3.323,4.198 3.479,4.396 0.156,0.198 10 false 2

A384845E04
0.552,6.438 1.625,6.635 1.073,0.198 10 false Battery 1.438,0.948 1.896,1.146 0.458,0.198 10 false AM1 2.302,0.969 2.76,1.167 0.458,0.198 10 false ST1 6.021,1.865 6.479,2.063 0.458,0.198 10 false STA 6.052,0.938 6.51,1.135 0.458,0.198 10 false NSW 6.25,3.219 6.708,3.417 0.458,0.198 10 false ECM 3.719,2.75 4.677,3.479 0.958,0.729 10 false Park/Neutral Position Switch 4.771,5.552 5.99,5.781 1.219,0.229 10 false Starter Assembly 1.271,1.563 2.802,1.979 1.531,0.417 10 false Ignition or Starter Switch Assembly 0.208,0.125 3.406,0.448 3.198,0.323 12 false w/o Entry and Start System: 3.74,2.542 4.823,2.74 1.083,0.198 10 false C36 1.292,1.427 1.635,1.625 0.344,0.198 10 false F12 0.688,1.208 1.146,1.406 0.458,0.198 10 false AM2 0.365,2.323 0.99,2.531 0.625,0.208 10 false J/B-B 1.156,4.323 1.615,4.521 0.458,0.198 10 false ST 0.365,4.927 1.229,5.146 0.865,0.219 10 false BATT MAIN 2.771,4.833 3.229,5.031 0.458,0.198 10 false ST 6.271,2.958 6.729,3.156 0.458,0.198 10 false A38 5.156,5.271 5.313,5.469 0.156,0.198 10 false 1 5.156,5.021 5.313,5.219 0.156,0.198 10 false 1 5.719,5.042 6.031,5.24 0.313,0.198 10 false *1 5.719,5.281 6.031,5.479 0.313,0.198 10 false *2 5.365,5.042 5.823,5.24 0.458,0.198 10 false C34 5.354,5.281 5.813,5.479 0.458,0.198 10 false C35 4.323,5.604 4.781,5.802 0.458,0.198 10 false C67 4.438,5.354 4.594,5.552 0.156,0.198 10 false 1 1.594,6.583 3.427,6.781 1.833,0.198 10 false *1: TMC Made 1.604,7.083 3.594,7.281 1.99,0.198 10 false *2: TMMT Made 1.271,0.969 1.427,1.167 0.156,0.198 10 false 5 2.625,0.979 2.781,1.177 0.156,0.198 10 false 6 5.781,0.969 6.094,1.167 0.313,0.198 10 false 57 5.792,1.74 6.104,1.938 0.313,0.198 10 false 29 5.51,2.135 5.667,2.333 0.156,0.198 10 false 4 4.969,3.146 5.125,3.344 0.156,0.198 10 false 9 2.448,4.063 2.604,4.26 0.156,0.198 10 false 5 3.208,4.083 3.365,4.281 0.156,0.198 10 false 3 2.458,4.479 2.615,4.677 0.156,0.198 10 false 1 3.198,4.458 3.354,4.656 0.156,0.198 10 false 2


for Manual Transaxle


A384834E01
1.073,6.24 2.146,6.438 1.073,0.198 10 false Battery 4.75,5.302 6.125,5.563 1.375,0.26 10 false Starter Assembly 6.042,2.635 6.5,2.833 0.458,0.198 10 false STA 6,0.792 6.458,0.99 0.458,0.198 10 false NSW 6.25,3.708 6.708,3.906 0.458,0.198 10 false ECM 0.781,0.771 1.396,0.969 0.615,0.198 10 false STAR 0.885,2.615 1.344,2.813 0.458,0.198 10 false STA 0.094,3.167 1.927,3.427 1.833,0.26 10 false Smart Key ECU Assembly 2.656,1.885 4.552,2.208 1.896,0.323 10 false Clutch Start Switch Assembly 0.115,0.156 2.656,0.563 2.542,0.406 12 false w/ Entry and Start System: 2.688,1.688 3.01,1.938 0.323,0.25 10 false A51 0.104,3.021 0.427,3.271 0.323,0.25 10 false M66 1.594,4.031 1.917,4.281 0.323,0.25 10 false ST 0.792,4.573 1.646,4.823 0.854,0.25 10 false BATT MAIN 3.469,4.552 3.792,4.802 0.323,0.25 10 false ST 6.26,3.531 6.583,3.781 0.323,0.25 10 false A38 2.167,6.781 4,6.979 1.833,0.198 10 false *1: TMC Made 2.177,7.229 4.167,7.427 1.99,0.198 10 false *2: TMMT Made 5.156,4.979 5.313,5.177 0.156,0.198 10 false 1 4.427,5.146 4.583,5.344 0.156,0.198 10 false 1 5.167,4.771 5.344,4.99 0.177,0.219 11 false 1 4.365,5.344 4.823,5.542 0.458,0.198 10 false C67 5.375,4.771 5.833,4.969 0.458,0.198 10 false C34 5.365,5.01 5.823,5.208 0.458,0.198 10 false C35 5.75,4.781 6.063,4.979 0.313,0.198 10 false *1 5.74,5.01 6.052,5.208 0.313,0.198 10 false *2 5.771,2.5 6.083,2.698 0.313,0.198 10 false 29 5.792,0.792 6.104,0.99 0.313,0.198 10 false 57 1.25,0.667 1.406,0.865 0.156,0.198 10 false 9 1.25,2.521 1.563,2.719 0.313,0.198 10 false 20 4.052,1.281 4.208,1.479 0.156,0.198 10 false 1 2.979,1.302 3.198,1.531 0.219,0.229 10 false 2 3.146,3.813 3.302,4.01 0.156,0.198 10 false 5 3.885,3.781 4.042,3.979 0.156,0.198 10 false 3 3.167,4.188 3.323,4.385 0.156,0.198 10 false 1 3.885,4.198 4.042,4.396 0.156,0.198 10 false 2

A384835E02
0.125,0.167 3.021,0.438 2.896,0.271 12 false w/o Entry and Start System: 0.583,6.479 1.313,6.698 0.729,0.219 10 false Battery 4.76,5.583 5.948,5.854 1.188,0.271 10 false Starter Assembly 6.031,1.896 6.49,2.094 0.458,0.198 10 false STA 6.042,0.927 6.5,1.125 0.458,0.198 10 false NSW 1.563,1.604 3.073,2.031 1.51,0.427 10 false Ignition or Starter Switch Assembly 6.313,3.49 6.771,3.688 0.458,0.198 10 false ECM 3.865,3.156 5.052,3.479 1.188,0.323 10 false Clutch Start Switch Assembly 1.573,1.417 2.031,1.615 0.458,0.198 10 false F12 3.833,2.979 4.292,3.177 0.458,0.198 10 false A51 6.313,3.333 6.771,3.531 0.458,0.198 10 false A38 0.74,1.198 1.198,1.396 0.458,0.198 10 false AM2 0.427,2.708 0.885,2.906 0.458,0.198 10 false J/B-B 1.396,4.333 1.854,4.531 0.458,0.198 10 false ST 0.375,4.906 1.156,5.156 0.781,0.25 10 false BATT MAIN 2.667,4.823 3.125,5.021 0.458,0.198 10 false ST 1.729,6.625 3.563,6.823 1.833,0.198 10 false *1: TMC Made 1.792,7.198 3.781,7.396 1.99,0.198 10 false *2: TMMT Made 4.448,5.396 4.604,5.594 0.156,0.198 10 false 1 5.177,5.021 5.333,5.229 0.156,0.208 10 false 1 5.167,5.271 5.323,5.469 0.156,0.198 10 false 1 4.365,5.615 4.823,5.813 0.458,0.198 10 false C67 5.365,5.031 5.823,5.229 0.458,0.198 10 false C34 5.344,5.271 5.802,5.469 0.458,0.198 10 false C35 5.729,5 6.042,5.198 0.313,0.198 10 false *1 5.729,5.25 6.042,5.448 0.313,0.198 10 false *2 1.906,0.969 2.365,1.167 0.458,0.198 10 false AM1 1.74,0.969 1.896,1.167 0.156,0.198 10 false 5 2.781,0.958 3.24,1.156 0.458,0.198 10 false ST1 3.083,0.958 3.24,1.156 0.156,0.198 10 false 6 4.99,2.563 5.146,2.76 0.156,0.198 10 false 2 3.948,2.542 4.104,2.74 0.156,0.198 10 false 1 2.375,4.083 2.531,4.281 0.156,0.198 10 false 5 3.125,4.094 3.281,4.292 0.156,0.198 10 false 3 2.385,4.458 2.542,4.656 0.156,0.198 10 false 1 3.135,4.458 3.292,4.656 0.156,0.198 10 false 2 5.792,1.802 6.104,2 0.313,0.198 10 false 29 5.781,0.958 6.094,1.156 0.313,0.198 10 false 57


CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for CVT A
for Manual Transaxle B




A

2.READ VALUE USING GTS (STARTER SW)

B

13.READ VALUE USING GTS (STARTER SW)
2.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

According to the display on the GTS, read the Data List.

Standard:
Condition Starter SW
Ignition switch ON OFF



f.

According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12 mph) or more.

Standard:
Condition Starter SW
Driving at 20 km/h (12.43 mph) or more (engine speed 1000 rpm or more) OFF



HINT:

If the result of either of the above is not as specified, proceed to the next step with the ignition switch ON, GTS connected and Data List item "Starter SW" selected.


Result:
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C


HINT:

If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter SW".



A

B

3.READ VALUE USING GTS (STARTER SW (CHECK FOR SHORT CIRCUIT))

C

8.READ VALUE USING GTS (STARTER SW (CHECK FOR SHORT CIRCUIT))
3.READ VALUE USING GTS (STARTER SW (CHECK FOR SHORT CIRCUIT))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Remove the ST relay from the No. 1 engine room relay block.


f.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON A
The Data List item "Starter SW" changes from ON to OFF B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

B

REPLACE ST RELAY

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


HINT:

The purpose of this step is to check for ST relay holder voltage under abnormal conditions.


a.

Remove the ST relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST relay holder 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

5.INSPECT PARK/NEUTRAL POSITION SWITCH (CHECK FOR SHORT CIRCUIT)
5.INSPECT PARK/NEUTRAL POSITION SWITCH (CHECK FOR SHORT CIRCUIT)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the park/neutral position switch connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected*1 B
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected*2 C


*1: for 2WD

*2: for AWD

HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

6.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

REPLACE PARK/NEUTRAL POSITION SWITCH

C

6.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

7.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)

B

7.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY)
a.

Disconnect A38 the ECM connector.


b.

Disconnect the C36 park/neutral position switch connector.


c.

Disconnect the M66 Certification ECU (smart key ECU assembly) connector.


d.

Remove the ST relay from the No. 1 engine room relay block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-29 (STA), C36-9 (L), M66-20 (STA), 2 (ST relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING GTS (STARTER SW (CHECK FOR SHORT CIRCUIT))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Remove the ST relay from the No. 1 engine room relay block.


f.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON A
The Data List item "Starter SW" changes from ON to OFF B


HINT:
·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

B

REPLACE ST RELAY

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>8NR-FTS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


HINT:

The purpose of this step is to check for ST relay holder voltage under abnormal conditions.


a.

Remove the ST relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST relay holder 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

11.INSPECT PARK/NEUTRAL POSITION SWITCH (CHECK FOR SHORT CIRCUIT)
11.INSPECT PARK/NEUTRAL POSITION SWITCH (CHECK FOR SHORT CIRCUIT)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the park/neutral position switch connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected*1 B
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected*2 C


*1: for 2WD

*2: for AWD

HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

12.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

REPLACE PARK/NEUTRAL POSITION SWITCH

C

12.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH - ST RELAY)

B

13.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

According to the display on the GTS, read the Data List.

Standard:
Condition Starter SW
Ignition switch ON OFF


HINT:

for Manual Transaxle: Read the Data List with the clutch pedal depressed.



f.

According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12 mph) or more.

Standard:
Condition Starter SW
Driving at 20 km/h (12.43 mph) or more (engine speed 1000 rpm or more) OFF


HINT:

for Manual Transaxle: Read the Data List with the clutch pedal depressed.



HINT:

If the result of either of the above is not as specified, proceed to the next step with the ignition switch ON, GTS connected and Data List item "Starter SW" selected.


Result:
Result Proceed to
OK A
NG (w/ Entry and Start System) B
NG (w/o Entry and Start System) C


HINT:

If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter SW".



A

B

14.READ VALUE USING GTS (STARTER SW(CHECK FOR SHORT CIRCUIT))

C

18.READ VALUE USING GTS (STARTER SW(CHECK FOR SHORT CIRCUIT))
14.READ VALUE USING GTS (STARTER SW(CHECK FOR SHORT CIRCUIT))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Remove the ST NO. 1 relay from the engine room relay block and junction block assembly.


f.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON A
The Data List item "Starter SW" changes from ON to OFF B


HINT:
·

Read the Data List with the clutch pedal depressed.

·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST NO. 1 relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

15.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

B

REPLACE ST RELAY

15.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


HINT:

The purpose of this step is to check for ST relay holder voltage under abnormal conditions.


a.

Remove the ST relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST relay holder 2 and body ground.

HINT:
·

Measure the voltage with the clutch pedal depressed.

·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

16.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
16.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected B


HINT:
·

Measure the voltage with the clutch pedal depressed and compare it with the voltage measured in the previous step.

·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

17.CHECK HARNESS AND CONNECTOR (ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY - ST RELAY)

B

17.CHECK HARNESS AND CONNECTOR (ECM - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the A38 ECM connector.


b.

Disconnect the M66 Certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A51 clutch start switch assembly connector.


d.

Remove the ST relay from the No. 1 engine room relay block.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-57 (NSW), A51-2 or M66-9 (STAR) - Body ground and other terminals Always 10 kΩ or higher
A38-29 (STA), A51-1, M66-20 (STA) or 2 (ST relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.READ VALUE USING GTS (STARTER SW(CHECK FOR SHORT CIRCUIT))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Remove the ST relay from the No. 1 engine room relay block.


f.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter SW" does not change from ON A
The Data List item "Starter SW" changes from ON to OFF B


HINT:
·

Read the Data List with the clutch pedal depressed.

·

When the result of the above inspection is "The Data List item "Starter SW" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

19.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

B

REPLACE ST RELAY

19.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>8NR-FTS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


HINT:

The purpose of this step is to check for ST relay holder voltage under abnormal conditions.


a.

Remove the ST relay from the No. 1 engine room relay block.


b.

Turn the ignition switch to ON.


Result:
Proceed to
NEXT


c.

Measure the voltage between ST relay holder 2 and body ground.

HINT:
·

Measure the voltage with the clutch pedal depressed.

·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.






NEXT

21.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
21.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST relay holder 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay holder 2 and body ground does not change when the connector is disconnected A
The voltage between ST relay holder 2 and body ground changes when the connector is disconnected B


HINT:
·

Measure the voltage with the clutch pedal depressed and compare it with the voltage measured in the previous step.

·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)

B