Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM J

8NR-FTS ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

·

w/ Entry and Start System:

-

When the engine is being cranked by engine switch operation:

Current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly or clutch start switch and then to terminal STA of the ECM (STA signal). The ECM then performs control to start the engine.



·

w/o Entry and Start System:

-

When the engine is being cranked by ignition or starter switch assembly operation:

Current flows from terminal ST2 of the ignition or starter switch assembly to the park/neutral position switch or clutch start switch assembly and then terminal STA of the ECM (STA signal). The ECM then performs control to start the engine.



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING GTS (STARTER SW)

B

24.READ VALUE USING GTS (STARTER SW)
2.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is turned to ON and the engine is started.


OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Cranking position ON


Result:
Result Proceed to
OK A
NG (for CVT) B
NG (for Manual Transaxle) C



A

3.INSPECT RELAY (ST RELAY)

B

9.INSPECT PARK/NEUTRAL POSITION SWITCH

C

18.INSPECT CLUTCH START SWITCH ASSEMBLY
3.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM)

NG

REPLACE ST RELAY

4.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM)
a.

Remove the ST relay from the No. 1 engine room relay block.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST relay holder) - A38-29 (STA) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BATTERY - ST RELAY)
a.
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


Remove the ST relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ST relay holder) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the No. 1 engine room relay block.


b.

Disconnect the C34 starter assembly (TMC Made) connector.


c.

Disconnect the C35 starter assembly (TMMT Made) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (TMC Made):
Tester Connection Condition Specified Condition
3 (ST relay holder) - C34-1 Always Below 1 Ω
3 (ST relay holder) or C34-1 - Body ground and other terminals Always 10 kΩ or higher


Standard Resistance (TMMT Made):
Tester Connection Condition Specified Condition
3 (ST relay holder) - C35-1 Always Below 1 Ω
3 (ST relay holder) or C35-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.
A384829C19
0.135,0.104 0.448,0.302 0.313,0.198 10 false *1 0.188,1.667 0.5,1.865 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 ST Relay Holder


Remove the ST relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (ST relay holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

8.INSPECT STARTER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

for Valeo Made Cold Area Specification Vehicles: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>STARTER (for Valeo Made Cold Area Specification Vehicles)>INSPECTION

for Valeo Made except Cold Area Specification Vehicles: Click hereEngine / Hybrid System>8NR-FTS (STARTING)>STARTER (for Valeo Made except Cold Area Specification Vehicles)>INSPECTION


Result:
Result Proceed to
OK A
NG (for Valeo Made Cold Area Specification Vehicles) B
NG (for Valeo Made except Cold Area Specification Vehicles) C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

C

9.INSPECT PARK/NEUTRAL POSITION SWITCH

Result:
Result Proceed to
OK A
NG (for 2WD) B
NG (for AWD) C



A

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH VOLTAGE)

B

REPLACE PARK/NEUTRAL POSITION SWITCH

C

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH VOLTAGE)
a.
A194118C30
0.26,2.26 0.698,2.521 0.438,0.26 2.719,3.083 2.146,2.438 true 0.229,0.135 0.438,0.302 0.208,0.167 10 false *a 0.344,2.292 1.292,2.823 0.948,0.531 10 false C36 2.76,3.125 2.979,3.281 0.219,0.156 10 false B
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C36-4 (B) - Body ground Engine cranking position 11 to 14 V



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG (w/ Entry and Start System) C
NG (w/o Entry and Start System) D



A

11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY - PARK/NEUTRAL POSITION SWITCH - ECM)

B

12.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH - ECM)

C

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM - PARK/NEUTRAL POSITION SWITCH)

D

16.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
11.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY - PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C36 park/neutral position switch connector.


c.

Remove the ST relay from the No. 1 engine room relay block.


d.

Disconnect the A38 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-20 (STA) - C36-9 (L) Always Below 1 Ω
2 (ST relay holder) - A38-29 (STA) Always Below 1 Ω
A38-29 (STA), M66-20 (STA), 2 (ST relay holder) or C36-9 (L) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the C36 park/neutral position switch connector.


b.

Remove the ST relay from the No. 1 engine room relay block.


c.

Disconnect the A38 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (ST relay holder) - C36-9 (L) Always Below 1 Ω
2 (ST relay holder) - A38-29 (STA) Always Below 1 Ω
A38-29 (STA), 2 (ST relay holder) or C36-9 (L) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>8NR-FTS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

14.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)
a.

Disconnect the F12 ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F12-5 (AM1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

15.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the C36 park/neutral position switch connector.


c.

Disconnect the A38 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-9 (STAR) - C36-4 (B) Always Below 1 Ω
A38-57 (NSW), M66-9 (STAR) or C36-4 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>8NR-FTS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

17.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)
a.

Disconnect the F12 ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F12-5 (AM1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

18.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY VOLTAGE)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY

19.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY VOLTAGE)
a.

Disconnect the A51 clutch start switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A51-2 - Body ground Engine cranking position 11 to 14 V



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
NG (w/ Entry and Start System) C
NG (w/o Entry and Start System) D



A

20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY - CLUTCH START SWITCH ASSEMBLY - ECM)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH START SWITCH ASSEMBLY - ST NO. 1 RELAY)

C

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM - CLUTCH START SWITCH ASSEMBLY)

D

22.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
20.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ST RELAY - CLUTCH START SWITCH ASSEMBLY - ECM)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A51 clutch start switch assembly connector.


c.

Remove the ST relay from the No. 1 engine room relay block.


d.

Disconnect the A38 ECM connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M66-20 (STA) - A51-1 Always Below 1 Ω
2 (ST relay holder) - A38-29 (STA) Always Below 1 Ω
A38-29 (STA), M66-20 (STA), 2 (ST relay holder) or A51-1 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ECM - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the M66 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A51 clutch start switch assembly connector.


c.

Disconnect the A38 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-57 (NSW) - A51-2 Always Below 1 Ω
M66-9 (STAR) - A51-2 Always Below 1 Ω
A38-57 (NSW), M66-9 (STAR) or A51-2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>8NR-FTS (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

23.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY VOLTAGE)
a.

Disconnect the F12 ignition or starter switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F12-5 (AM1) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Starter SW.

Powertrain > Engine > Data List
Tester Display
Starter SW
50003 372 11

e.

Check the value displayed on the GTS when the ignition switch is turned to ON and the engine is started.


OK:
Condition GTS Display (Starter SW)
Ignition switch ON OFF
Cranking position ON


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST NO. 1 RELAY - ECM)