Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Power Seat) › from 2019.09
RM32H0E _58 Vehicle Interior _059623 SEAT _0404461 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·
B458500

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·
B407261

Wear protective gloves. Sharp areas on the parts may injure your hands.



HINT:
·

Power seat is available only on the driver side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 72108 1.INSTALL UPPER SEAT TRACK RAIL SUB-ASSEMBLY

Hide 85822B 2.INSTALL POWER SEAT TILT MOTOR ASSEMBLY

a.
B447557N02
2.333,0.323 2.49,0.521 0.156,0.198 10 true A 0.802,0.823 0.958,1.021 0.156,0.198 10 true B 2.177,1.49 2.333,1.688 0.156,0.198 10 true B

Install the power seat tilt motor assembly with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Bolt (A) is shorter than bolt (B). Make sure to install them to the correct positions.



Hide 85822C 3.INSTALL POWER SEAT LIFTER MOTOR ASSEMBLY

a.

Install the power seat lifter motor assembly.

i.
B462120C02
1.896,0.635 2.792,0.313 true 2.146,0.688 2.792,1.031 true 0.948,0.271 1.406,0.656 true 0.531,1.344 1.146,1.073 true 0.625,0.167 0.938,0.323 0.313,0.156 10 true *a 0.323,1.26 0.635,1.417 0.313,0.156 10 false *b 2.802,0.938 3.115,1.094 0.313,0.156 10 true *1 2.802,0.229 3.115,0.385 0.313,0.156 10 true *2
*1 Front Seat Vertical Housing Sub-assembly
*2 Front Seat Adjuster Assembly
*a Stud Bolt of the Front Seat Vertical Housing Sub-assembly
*b Hole of the Front Seat Adjuster Assembly


Install the front seat vertical housing sub-assembly.

NOTICE:
·

Make sure to insert the stud bolt of the front seat vertical housing sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.

·

Make sure to position the front seat adjuster assembly so that when the front seat vertical housing sub-assembly is installed, their gears will be positioned as shown in the illustration.




ii.
B447555

Install the vertical adjuster spacer.


iii.
B447554N02
2.073,0.125 2.229,0.323 0.156,0.198 10 false 1 0.906,0.677 1.063,0.875 0.156,0.198 10 true 2 2.125,1.885 2.281,2.083 0.156,0.198 10 true 3

Install the front seat adjuster plate with the 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

NOTICE:

Tighten the nuts in the order shown in the illustration.




Hide 71874C 4.INSTALL FRONT SEAT LOWER CUSHION SHIELD

a.
B563656C01
1.5,1.865 1.333,1.625 true 1.781,1.719 1.615,1.479 true 1.573,1.771 1.823,1.979 0.25,0.208 10 false (A) 1.854,1.635 2.125,1.875 0.271,0.24 10 true (B)
V113147

Install in this direction (1)
V113148

Install in this direction (2)


Engage the guide (B) as shown in the illustration.


b.

Engage the guide (A) as shown in the illustration.


c.
B439744

Engage the claw to install the front seat lower cushion shield.


Hide 5.INSTALL SEAT POSITION AIRBAG SENSOR WITH BRACKET (w/ Seat Position Airbag Sensor)

Hide 72277A 6.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (w/ Seat Position Airbag Sensor)

Hide 87501B 7.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY

Hide 7181B 8.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER

a.
B558468C01
0,0 0,0 false
V113147

Install in this direction


Engage the claws and guides to install the front seat cushion wire harness holder as shown in the illustration.


b.
B558466

Install the 2 screws.


Hide 71052A 9.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY

a.
B558465

Engage the hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.


Hide 82192 10.INSTALL FRONT SEAT WIRE

a.
B558464

Engage the clamps to install the front seat wire.


b.
B558463

Engage the claw and clamps.


c.

Connect the 3 connectors.


d.
B558462

Engage the clamp.


e.

Connect the connector.


Hide 82192B 11.INSTALL NO. 2 FRONT SEAT WIRE (w/ Seat Position Airbag Sensor)

a.
B558461

Engage the claw.


b.

Engage the clamp to install the No. 2 front seat wire.


c.

Connect the connector.


Hide 71874A 12.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

a.
B439739C02
2.333,0.635 3.115,0.635 true 2.063,1.698 2.865,1.698 true 3.146,0.542 3.333,0.74 0.188,0.198 10 false *a 2.917,1.625 3.229,1.781 0.313,0.156 10 false *b
*a Hook
*b Guide


Engage the guide.


b.

Engage the claw.


c.

Engage the hook to install the front seat lower cushion shield LH.


Hide 71873A 13.INSTALL FRONT SEAT LOWER CUSHION SHIELD

a.
B439740C02
2.5,0.281 3.094,0.281 true 2.135,1.625 2.917,1.625 false 3.135,0.188 3.333,0.375 0.198,0.188 10 false *a 2.948,1.552 3.26,1.708 0.313,0.156 10 false *b
*a Hook
*b Guide


Engage the guide.


b.

Engage the claw.


c.

Engage the hook to install the front seat lower cushion shield.


Hide 71876G 14.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER LH

a.
B439737

Engage the claws to install the LH seat reclining adjuster inside cover LH.


b.
B439736

Engage the claw.


Hide 71875G 15.INSTALL LH SEAT RECLINING ADJUSTER INSIDE COVER RH

a.
B439738

Engage the claws to install the LH seat reclining adjuster inside cover RH.


Hide 87510L 16.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY

Hide 71072S 17.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

NOTICE:

When installing a separate type front seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION


a.
B458475

Engage the claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.

NOTICE:

Be careful not to damage the separate type front seat cushion cover.



Hide 18.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

Engage the hooks (A) and hooks (B) to install the separate type front seat cushion cover with pad.

B558460E01
0.99,1.031 1.26,0.802 true 0.979,1.01 1.292,1.458 true 1,1.052 1.271,1.938 true 5.813,0.76 6.198,1.604 true 5.802,1.469 6.198,1.604 true 5.521,2.219 6.188,1.615 true 3.531,2.406 3.844,2.219 true 3.521,2.438 3.208,2.219 true 3.281,0.51 3.583,0.333 true 3.927,0.5 3.604,0.344 true 0.729,0.906 0.958,1.125 0.229,0.219 10 true (B) 3.385,2.448 3.615,2.667 0.229,0.219 10 true (B) 6.24,1.49 6.469,1.708 0.229,0.219 10 true (B) 3.51,0.083 3.76,0.302 0.25,0.219 10 true (A)


b.
B490192

Engage the clamp.


c.

Connect the connector.


Hide 71759B 19.INSTALL FRONT SEATBACK HOOK

a.
B558484

Engage the claws to install the 2 front seatback hooks to the front seatback frame sub-assembly.


Hide 8219B 20.INSTALL NO. 2 FRONT SEAT WIRE

a.
B558486

Engage the clamps to install the No. 2 front seat wire.


Hide 72760D 22.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY

Hide 87510N 24.INSTALL FRONT SEATBACK HEATER ASSEMBLY

Hide 71074S 25.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

NOTICE:

When installing a separate type front seatback cover, refer to Precaution in order to prevent wrinkles from forming.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION


a.
B458476

Engage the claws to install the separate type front seatback cover to the separate type front seatback pad.

NOTICE:

Be careful not to damage the separate type front seatback cover.



Hide 26.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

a.

Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.


Hide 71931 27.INSTALL FRONT SEAT HEADREST SUPPORT

a.
B458474C03
0,0 0,0 false
V113147

Install in this direction


Engage the claws to install the 2 front seat headrest supports as shown in the illustration.


b.
B558458

Close the 2 fasteners as shown in the illustration.


c.
B558456

Engage the clamp.


d.
B558455

Engage the hooks.


Hide 28.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.
B558454

Engage the guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.


b.

Install the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B485456

Engage the clamp.


d.

Connect the connector.


e.
B471088

Engage the clamp.


f.

Connect the connector.


g.
B471098

Engage the claw.


h.

Engage the clamps to connect the front seat airbag assembly wire harness.


i.
B557334

Engage the hooks.


j.
B563658

Engage the hook.


Hide 84922C 29.INSTALL FRONT POWER SEAT SWITCH

Hide 72714 30.INSTALL SEAT ADJUSTER SHIELD CLAMP BRACKET

a.
B439726

Install the seat adjuster shield clamp bracket with the 2 screws.


Hide 84921K 31.INSTALL RECLINING POWER SEAT SWITCH KNOB

a.
B439748

Engage the claws to install the reclining power seat switch knob.


Hide 84921D 32.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

a.
B439749

Engage the claws to install the slide and vertical power seat switch knob.


Hide 71862 33.INSTALL FRONT SEAT INNER CUSHION SHIELD

a.
B557332C01
0,0 0,0 false
V113147

Install in this direction


Engage the claws to install the front seat inner cushion shield as shown in the illustration.


b.
B557330

Engage the claws and guides.


Hide 71812D 34.INSTALL FRONT SEAT CUSHION SHIELD

a.
B439723

Connect the connector.


b.
B557329C01
1.698,0.344 2.604,0.344 true 0.542,1.052 0.792,1.156 true 1.698,0.354 2.24,0.646 true 0.292,0.927 0.521,1.146 0.229,0.219 10 true (A) 1.458,0.24 1.688,0.458 0.229,0.219 10 true (B)
V113147

Install in this direction (1)
V113148

Install in this direction (2)


Engage the guide (A) as shown in the illustration.


c.

Engage the claws and guides (B) to install the front seat cushion shield as shown in the illustration.


d.
B439720

Engage the claws.


Hide 71868A 35.INSTALL NO. 1 FRONT SEAT INNER CUSHION SHIELD

a.
B557326C01
0,0 0,0 false
V113147

Install in this direction


Engage the claw and guides to install the No. 1 front seat inner cushion shield as shown in the illustration.


b.
B557324C01
0,0 0,0 false
V113147

Install in this direction


Engage the guide as shown in the illustration.


c.
B439716

Install the clip.


Hide 71074S 36.CONNECT SEPARATE TYPE FRONT SEATBACK COVER

a.
B439715

Connect the rubber band of the separate type front seatback cover.


Hide 73240 37.INSTALL FRONT SEAT INNER BELT ASSEMBLY