Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

When the dynamic radar cruise control system*1, pre-collision system*1 or brake hold control system operates, the skid control ECU outputs a stop light drive output (STPO) signal to illuminate the stop lights.

*1: w/ Pre-collision System

DTC No. Detection Item DTC Detection Condition Trouble Area
C1380 Stop Light Control Relay Malfunction Either condition is met:
·

When the voltage at the +BS terminal is between 10 V or more and the stop light control relay drive output (STPO) is on, a signal is not input to the STP2 terminal for 5 seconds or more.

·

When the voltage at the +BS terminal is between 10 V or more and the stop light control relay drive output (STPO) is off, the signal at the STP terminal is different from the input signal at the STP2 terminal for 5 seconds or more.


·

Wire harness or connector

·

Stop light control relay (Stop light switch assembly)

·

Skid control ECU (brake actuator assembly)



DTC Detection Conditions: C1380
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition - - -
Malfunction Status When the voltage at the +BS terminal is between 10 V or more and the stop light control relay drive output (STPO) is on, a signal is not input to the STP2 terminal. ○ -
When the voltage at the +BS terminal is between 10 V or more and the stop light control relay drive output (STPO) is off, the signal at the STP terminal is different from the input signal at the STP2 terminal. - ○
Detection Time 5 seconds or more 5 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C416944E01
2.5,1.198 2.958,1.396 0.458,0.198 10 false STP 4.792,2.729 5.25,2.927 0.458,0.198 10 false STP 5.854,0.323 6.313,0.521 0.458,0.198 10 false STP 0.917,0.323 1.375,0.521 0.458,0.198 10 false STP1 0.302,0.698 0.76,0.896 0.458,0.198 10 false M67 0.281,0.875 1.813,1.354 1.531,0.479 10 false Certification ECU (Smart Key ECU Assembly)*1 2.021,1.583 2.479,1.781 0.458,0.198 10 false A38 2.01,1.76 2.469,1.958 0.458,0.198 10 false ECM 4.521,2.729 4.979,2.927 0.458,0.198 10 false 42 2.896,1.073 3.354,1.271 0.458,0.198 10 false 9 5.635,0.188 6.094,0.385 0.458,0.198 10 false 8 4.26,1.063 4.719,1.26 0.458,0.198 10 false 4 5.74,0.719 6.198,0.917 0.458,0.198 10 false F18 5.708,0.885 7.115,1.448 1.406,0.563 10 false Shift Lock Control Unit Assembly*2 4.365,1.573 4.823,1.771 0.458,0.198 10 false F19 4.354,1.74 5.76,2.167 1.406,0.427 10 false Shift Lock Control Unit Assembly*1 6.656,5.313 7.115,5.51 0.458,0.198 10 false B 3.958,5.302 4.417,5.5 0.458,0.198 10 false A 0.625,6.469 2.875,6.698 2.25,0.229 10 false : CAN Communication Line 4.458,1.177 4.917,1.375 0.458,0.198 10 false STP 4.792,3.583 5.25,3.781 0.458,0.198 10 false STPO 4.802,4.5 5.26,4.698 0.458,0.198 10 false STP2 4.635,5.313 5.094,5.51 0.458,0.198 10 false A42 4.625,5.49 6.177,6.104 1.552,0.615 10 false Skid Control ECU (Brake Actuator Assembly) 1.396,5.146 1.854,5.344 0.458,0.198 10 false A91 1.385,5.323 3.49,5.635 2.104,0.313 10 false Stop Light Switch Assembly 0.656,3.375 1.115,3.573 0.458,0.198 10 false STOP 0.521,3.958 1.583,4.5 1.063,0.542 10 false from Battery 1.406,3.052 1.865,3.25 0.458,0.198 10 false 7 1.615,4.51 2.073,4.708 0.458,0.198 10 false GND 1.615,3.063 2.073,3.26 0.458,0.198 10 false B 1.427,4.51 1.885,4.708 0.458,0.198 10 false 2 3.229,2.698 3.688,2.896 0.458,0.198 10 false 3 3.208,4.5 3.667,4.698 0.458,0.198 10 false 1 3.208,3.583 3.667,3.781 0.458,0.198 10 false 4 2.969,2.75 3.427,2.948 0.458,0.198 10 false L 2.802,3.573 3.26,3.771 0.458,0.198 10 false ACC 2.792,4.51 3.25,4.708 0.458,0.198 10 false OUT 1.354,0.198 1.813,0.396 0.458,0.198 10 false 25 4.542,3.573 5,3.771 0.458,0.198 10 false 10 4.521,4.5 4.979,4.698 0.458,0.198 10 false 44 4.479,0.208 4.823,0.448 0.344,0.24 10 false *3 3.844,1.083 4.188,1.323 0.344,0.24 10 false *3 1.49,6.125 3.594,6.438 2.104,0.313 10 false *1: w/ Entry and Start System 3.75,6.125 5.854,6.438 2.104,0.313 10 false *2: w/o Entry and Start System 6.208,6.135 7.042,6.427 0.833,0.292 10 false *3: CVT

C416945E03
6.854,0.125 7.01,0.323 0.156,0.198 10 false B 3.719,1.958 5.729,2.229 2.01,0.271 10 false *1: w/ Pre-collision System 4.073,1.375 6.99,1.823 2.917,0.448 10 false Millimeter Wave Radar Sensor Assembly*1 4.094,4.365 6.104,4.635 2.01,0.271 10 false : CAN Communication Line 3.729,2.365 7.01,2.771 3.281,0.406 10 false *2: for TMC Made with Triple Beam Headlight 3.74,2.802 6.979,3.25 3.24,0.448 10 false *3: for TMC Made with Single Beam Headlight 3.052,0.135 3.208,0.333 0.156,0.198 10 false A 1.115,0.458 1.875,0.667 0.76,0.208 10 false E2 1.115,1.844 1.271,2.042 0.156,0.198 10 false E 1.125,3.385 1.281,3.583 0.156,0.198 10 false E 1.99,1.833 2.146,2.031 0.156,0.198 10 false B 2,3.385 2.156,3.583 0.156,0.198 10 false B 1.469,2.156 2.063,2.365 0.594,0.208 10 false Stop 1.427,0.76 2.021,0.969 0.594,0.208 10 false Stop 1.458,3.708 2.052,3.917 0.594,0.208 10 false Stop 1.875,0.469 2.427,0.688 0.552,0.219 10 false B2 2.26,0.458 2.417,0.656 0.156,0.198 10 false 1 2.25,1.844 2.406,2.042 0.156,0.198 10 false 1 2.26,3.375 2.417,3.573 0.156,0.198 10 false 1 0.906,0.448 1.063,0.646 0.156,0.198 10 false 2 0.906,1.844 1.063,2.042 0.156,0.198 10 false 2 0.875,3.375 1.031,3.573 0.156,0.198 10 false 2 0.625,2.396 2.813,2.615 2.188,0.219 10 false M48*2, M115*3, q1*4, q2*5 0.948,1.156 2.958,1.427 2.01,0.271 10 false Center Stop Light Assembly 0.938,0.99 1.698,1.198 0.76,0.208 10 false c1 0.667,4.156 3.208,4.469 2.542,0.313 10 false Rear Combination Light Assembly RH 0.688,3.958 2.74,4.208 2.052,0.25 10 false M47*2, M114*3, o1*4, o2*5 0.615,2.594 3.156,2.906 2.542,0.313 10 false Rear Combination Light Assembly LH 3.76,3.271 7,3.719 3.24,0.448 10 false *4: for TMMT Made with Triple Beam Headlight 3.781,3.688 7.021,4.135 3.24,0.448 10 false *5: for TMMT Made with Single Beam Headlight

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin*1.

*1: w/ Entry and Start System




PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STP, STPO AND STP2 TERMINAL)
a.

Turn the ignition switch off.


b.
C360727C23
1.5,0.135 2,0.385 0.5,0.25 3.01,1.833 2.427,1 true 2.625,0.292 2.188,0.927 true 2.01,1.292 1.625,1.844 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 1.594,0.167 1.948,0.365 0.354,0.198 10 false A42 1.448,1.854 1.99,2.031 0.542,0.177 10 false STPO 2.865,1.844 3.323,2.021 0.458,0.177 10 false STP2 2.708,0.177 3.25,0.354 0.542,0.177 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-42 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V
A42-10 (STPO) - Body ground Always 11 to 14 V
A42-44 (STP2) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1.5 V



Result:
Result Proceed to
All terminal voltage is normal A
Only STP terminal voltage abnormal B
Only STPO terminal voltage abnormal C
Only STP2 terminal voltage abnormal D
STPO terminal and STP2 terminal voltage abnormal E



A

2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

B

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ECM)

C

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

D

14.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

E

18.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test.


b.

Perform "Active Test" according to the display on the GTS.

Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) ON or OFF Stop lights come on
Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display
Stop Light Relay
50004 105 5
OK:

Stop light turns ON/OFF in response to the GTS operation



Result:
Proceed to
OK
NG



OK

3.CHECK FOR DTC

NG

4.INSPECT BRAKE ACTUATOR ASSEMBLY
3.CHECK FOR DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

b.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test.


c.

Perform "Active Test" according to the display on the GTS.

Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) ON or OFF Stop lights come on
Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display
Stop Light Relay
50004 105 5

d.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Clear DTCs
50002 105

Result:
Result Proceed to
DTC C1380 is output. (for LHD) A
DTC C1380 is output. (for RHD) B
DTC C1380 is not output. C



A

B

C

4.INSPECT BRAKE ACTUATOR ASSEMBLY
a.

Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Active Test.


b.

Perform "Active Test" according to the display on the GTS.

Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) ON or OFF Stop lights come on
Chassis > ABS/VSC/TRC/EPB > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.
C401043C61
0.448,0.448 0.781,0.698 0.333,0.25 2.094,1.688 1.74,1.052 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.5,0.5 0.958,0.698 0.458,0.198 10 false A91 2.021,1.708 2.479,1.906 0.458,0.198 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-4 (ACC) - Body ground Active Test is ON Below 1.5 V



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

REPLACE STOP LIGHT SWITCH ASSEMBLY

B

C

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ECM)
a.
C360727C62
1.344,0.115 1.792,0.365 0.448,0.25 2.542,0.365 2.188,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.594,0.26 3.021,0.448 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A38 ECM connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A42-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Result Proceed to
OK (for 8NR-FTS) A
OK (for 3ZR-FAE) B
NG (w/ Entry and Start System) C
NG (for CVT without Entry and Start System) D
NG (for Manual Transaxle without Entry and Start System) E



A

B

C

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SMART KEY ECU ASSEMBLY)

D

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

E

11.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SMART KEY ECU ASSEMBLY)
a.
C360727C62
1.344,0.115 1.792,0.365 0.448,0.25 2.542,0.365 2.188,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.594,0.26 3.021,0.448 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the M67 certification ECU (smart key ECU assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A42-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Result Proceed to
OK A
NG (for CVT) B
NG (for Manual Transaxle) C



A

REPLACE SMART KEY ECU ASSEMBLY

B

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

C

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C360727C62
1.344,0.115 1.792,0.365 0.448,0.25 2.542,0.365 2.188,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.594,0.26 3.021,0.448 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the F19 shift lock control ECU (shift lock control unit assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A42-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Result Proceed to
OK (for K114) A
OK (for K313) B
OK (for K313F) C
NG D



A

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

B

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

C

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

D

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
C360727C62
1.344,0.115 1.792,0.365 0.448,0.25 2.542,0.365 2.188,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.594,0.26 3.021,0.448 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A91 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-42 (STP) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A91 stop light switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-42 (STP) - A91-3 (L) Always Below 1 Ω
A42-42 (STP) or A91-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C360727C62
1.344,0.115 1.792,0.365 0.448,0.25 2.542,0.365 2.188,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.594,0.26 3.021,0.448 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the F18 shift lock control ECU (shift lock control unit assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A42-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.



Result:
Result Proceed to
OK (for K114) A
OK (for K313) B
OK (for K313F) C
NG D



A

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

B

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

C

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

D

11.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
11.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
C360727C62
1.344,0.115 1.792,0.365 0.448,0.25 2.542,0.365 2.188,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.594,0.26 3.021,0.448 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A91 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-42 (STP) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-42 (STP) - A91-3 (L) Always Below 1 Ω
A42-42 (STP) or A91-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A91 stop light switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-10 (STPO) - A91-4 (ACC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.
C360727C67
1.344,0.115 1.792,0.365 0.448,0.25 2.802,0.313 2.448,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.844,0.25 3.271,0.438 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the M48*1, M115*2, q1*3 or q2*4 rear combination light assembly LH connector.

*1: for TMC Made with Triple Beam Headlight

*2: for TMC Made with Single Beam Headlight

*3: for TMMT Made with Triple Beam Headlight

*4: for TMMT Made with Single Beam Headlight



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-44 (STP2) - Body ground Brake pedal depressed 11 to 14 V
A42-44 (STP2) - Body ground Brake pedal released Below 1.5 V



Result:
Reult Proceed to
OK (for LED Type) A
OK (for Bulb Type) B
NG C



A

B

C

15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
a.
C360727C67
1.344,0.115 1.792,0.365 0.448,0.25 2.802,0.313 2.448,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.844,0.25 3.271,0.438 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the M48*1, M115*2, q1*3 or q2*4 rear combination light assembly LH connector.


*1: for TMC Made with Triple Beam Headlight

*2: for TMC Made with Single Beam Headlight

*3: for TMMT Made with Triple Beam Headlight

*4: for TMMT Made with Single Beam Headlight


d.

Disconnect the M47*1, M114*2, o1*3 or o2*4 rear combination light assembly RH connector.


*1: for TMC Made with Triple Beam Headlight

*2: for TMC Made with Single Beam Headlight

*3: for TMMT Made with Triple Beam Headlight

*4: for TMMT Made with Single Beam Headlight


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-44 (STP2) - Body ground Brake pedal depressed 11 to 14 V
A42-44 (STP2) - Body ground Brake pedal released Below 1.5 V



Result:
Result Proceed to
OK (for LED Type) A
OK (for Bulb Type) B
NG C



A

B

C

16.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
16.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - CENTER STOP LIGHT ASSEMBLY)
a.
C360727C67
1.344,0.115 1.792,0.365 0.448,0.25 2.802,0.313 2.448,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.448,0.156 1.792,0.375 0.344,0.219 10 false A42 2.844,0.25 3.271,0.438 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.

Disconnect the M48*1, M115*2, q1*3 or q2*4 rear combination light assembly LH connector.


*1: for TMC Made with Triple Beam Headlight

*2: for TMC Made with Single Beam Headlight

*3: for TMMT Made with Triple Beam Headlight

*4: for TMMT Made with Single Beam Headlight


d.

Disconnect the M47*1, M114*2, o1*3 or o2*4 rear combination light assembly RH connector.


*1: for TMC Made with Triple Beam Headlight

*2: for TMC Made with Single Beam Headlight

*3: for TMMT Made with Triple Beam Headlight

*4: for TMMT Made with Single Beam Headlight


e.

Disconnect the c1 center stop light assembly connector.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-44 (STP2) - Body ground Brake pedal depressed 11 to 14 V
A42-44 (STP2) - Body ground Brake pedal released Below 1.5 V



Result:
Proceed to
OK
NG



OK

NG

17.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
17.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the M48*1, M115*2, q1*3 or q2*4 rear combination light assembly LH connector.


*1: for TMC Made with Triple Beam Headlight

*2: for TMC Made with Single Beam Headlight

*3: for TMMT Made with Triple Beam Headlight

*4: for TMMT Made with Single Beam Headlight


d.

Disconnect the M47*1, M114*2, o1*3 or o2*4 rear combination light assembly RH connector.


*1: for TMC Made with Triple Beam Headlight

*2: for TMC Made with Single Beam Headlight

*3: for TMMT Made with Triple Beam Headlight

*4: for TMMT Made with Single Beam Headlight


e.

Disconnect the c1 center stop light assembly connector.


f.

Disconnect the A91 stop light switch assembly connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-1 (OUT) - A42-44 (STP2) Always Below 1 Ω
A91-1 (OUT) or A42-44 (STP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
a.

Turn the ignition switch off.


b.
C401043C51
0.448,0.448 0.781,0.698 0.333,0.25 2.25,1.583 1.99,1.052 true 0.979,1.656 1.281,1.063 true 0.188,0.177 0.5,0.333 0.313,0.156 10 false *a 0.51,0.5 0.969,0.698 0.458,0.198 10 false A91 2.146,1.635 2.604,1.833 0.458,0.198 10 false GND 0.917,1.688 1.375,1.885 0.458,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A91-2 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A91-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A91 stop light switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-10 (STPO) - A91-4 (ACC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR