Home › Suspension › REAR SUSPENSION › REAR SUSPENSION MEMBER (for 2WD) › from 2019.09
RM32H0E _53 Suspension _059601 REAR SUSPENSION _0292271 REAR SUSPENSION MEMBER(for 2WD) A

REAR SUSPENSION  REAR SUSPENSION MEMBER(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear suspension member sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1 w/ Height Control Sensor

Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Removal/installation of rear height control sensor sub-assembly LH*1 Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system
·

Measurement of ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


·

for 8NR-FTS:

(Click here)

·

for 3ZR-FAE:

(Click here)



CAUTION:
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 17430 2.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 58166 3.REMOVE FRONT FLOOR COVER LH (w/ Cover)

Hide 58165B 4.INSTALL FRONT FLOOR COVER RH (w/ Cover)

HINT:

Perform the same procedure as for the LH side.


Hide 57628C 5.REMOVE REAR FLOOR SIDE MEMBER COVER LH

Hide 57627A 6.REMOVE REAR FLOOR SIDE MEMBER COVER RH

Hide 47319F 7.SEPARATE REAR FLEXIBLE HOSE LH

a.

Remove the bolt and separate the rear flexible hose LH from the flexible hose bracket.


Hide 47318F 8.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Perform the same procedure as for the LH side.


Hide 89408C 9.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 48840A 10.REMOVE REAR STABILIZER LINK ASSEMBLY LH

Hide 48830D 11.REMOVE REAR STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48812 12.REMOVE REAR STABILIZER BAR

Hide 48231B 13.REMOVE REAR COIL SPRING LH

Hide 48231A 14.REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as for the LH side.


Hide 48258C 15.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 16.REMOVE REAR LOWER COIL SPRING INSULATOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 48740F 17.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

Hide 48730F 18.REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48720A 19.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

Hide 48710A 20.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48790 21.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY LH

a.
C365599

Remove the bolt and nut and separate the rear upper control arm assembly LH from the rear axle carrier sub-assembly LH.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48770A 22.SEPARATE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 51206A 23.REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY

a.

w/ Height Control Sensor:

i.
C365612

Disengage the clamp to separate the height control sensor wire harness.



b.
C365600C01
1.938,3.479 2.188,2.885 true 2.281,3.344 2.604,3.344 true 3.021,4.063 2.75,3.844 true 1.094,3.844 1.26,3.656 true 0.417,3.938 0.521,3.771 true 3.052,3.99 3.313,4.188 0.26,0.198 10 false *a 0.281,3.969 0.542,4.167 0.26,0.198 10 true *b 0.938,3.885 1.198,4.083 0.26,0.198 10 true *b 2.656,3.208 2.917,3.406 0.26,0.198 10 true *b 2.219,2.667 2.479,2.865 0.26,0.198 10 true *b
*a Engine Lifter
*b Attachment
V100155

Attachment and Wooden Block Placement Location


Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

CAUTION:
·
C345782


·

The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.




c.

Remove the 2 bolts and 2 nuts.


d.

Slowly lower the rear suspension member sub-assembly.

NOTICE:

When lowering the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48790 24.REMOVE REAR UPPER CONTROL ARM ASSEMBLY LH

Hide 48770A 25.REMOVE REAR UPPER CONTROL ARM ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51249A 26.REMOVE REAR SUSPENSION MEMBER DAMPER

a.
C366717

Remove the 2 bolts and rear suspension member damper from the rear suspension member sub-assembly.


Hide 51284 27.REMOVE REAR SUSPENSION MEMBER HOLE COVER

a.
C365601C01
0.115,0.073 0.396,0.292 0.281,0.219 10 true *a 0.135,2.198 0.417,2.417 0.281,0.219 10 true *b
*a for LH Side
*b for RH Side


Remove the 4 rear suspension member hole covers from the rear suspension member sub-assembly as shown in the illustration.


Hide 28.REMOVE HOLE PLUG

a.
C365602

Remove the 7 hole plugs from the rear suspension member sub-assembly as shown in the illustration.