Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL INJECTOR › from 2020.08
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293895 FUEL INJECTOR A

8NR-FTS FUEL  FUEL INJECTOR  INSTALLATION  


PROCEDURE

Hide 23255A 1.INSTALL FUEL INJECTOR SEAL

a.
A273083C04
0.823,0.333 1.042,0.521 0.219,0.188 10 false *a
*a Area to be Cleaned


Apply engine conditioner to the area shown in the illustration. Using a piece of cloth, clean carbon deposits from the fuel injector assembly and its grooves.

NOTICE:
·

Do not clean the tip of the fuel injector assembly.

·

Do not use a wire brush to clean the fuel injector assembly.

·

If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.




b.
A273084C03
1.156,0.552 1.073,0.552 1.073,0.552 0.833,1.135 false 2.042,0.865 2.552,0.865 2.552,0.865 2.552,1.677 false 2.25,1.667 2.25,0.865 false 1.219,0.469 1.417,0.667 0.198,0.198 10 false *a 1.865,0.792 2.063,0.99 0.198,0.198 10 false *b
*a SST (Guide)
*b Chamfer


Apply engine oil to the fuel injector assembly contact surface of SST (guide), then attach SST (guide) to the fuel injector assembly with the chamfer facing the tip of the fuel injector assembly as shown in the illustration.

SST
09260-39021  (09261-03020)


c.
A273085C03
0.99,2.635 1.49,2.635 false 1.01,2.802 1.396,3.042 1.396,3.042 1.49,3.042 false 1.531,2.563 1.729,2.76 0.198,0.198 10 false *a 2.771,0.563 2.969,0.76 0.198,0.198 10 false *c 1.979,0.552 2.177,0.75 0.198,0.198 10 false *b 1.542,2.969 1.74,3.167 0.198,0.198 10 false *1
*1 Fuel Injector Seal
*a SST (Holder)
*b Correct
*c Incorrect


Install a new fuel injector seal to SST (holder).

SST
09260-39021  (09261-03011)

NOTICE:

Be careful not to install the fuel injector seal to SST (holder) at an angle. Doing so will stretch the fuel injector seal.



d.
A273086C03
0.781,1.073 1.375,0.438 1.375,0.438 1.469,0.438 true 1.031,1.667 1.625,2.688 1.625,2.688 1.719,2.688 true 1.781,2.625 1.979,2.823 0.198,0.198 10 false *b 1.552,0.375 1.75,0.573 0.198,0.198 10 false *a
*a SST (Holder)
*b SST (Guide)


Install SST (holder) with the fuel injector seal to the tip of the fuel injector assembly. Slide the fuel injector seal downward into the fuel injector assembly groove with your fingers as shown in the illustration.

SST
09260-39021  (09261-03011, 09261-03020)

HINT:

Check that the fuel injector seal is seated in the fuel injector assembly groove as shown in the illustration.



e.
A273087C04
0.885,1.625 1.833,2.948 1.833,2.948 1.938,2.948 true 1.99,2.896 2.188,3.094 0.198,0.198 10 false *a
*a SST (Guide)


Slowly slide SST (guide) toward the tip of the fuel injector assembly. When the fuel injector assembly contact surface of SST (guide) aligns with the fuel injector seal as shown in the illustration, hold the position for 5 seconds or more to fully seat the fuel injector seal into the fuel injector assembly groove.

SST
09260-39021  (09261-03020)

NOTICE:

Make sure the fuel injector seal is not pinched between SST (guide) and the edge of the fuel injector assembly groove. Replace the fuel injector seal if it becomes damaged.


HINT:
·

Set SST (guide) so that its bottom surface is flush with the fuel injector seal.

·

If it is difficult to slide SST (guide) upward, slowly wiggle it from side to side while sliding it up the fuel injector assembly little by little.




f.
A273088C03
0.563,2.729 0.765,2.927 0.202,0.198 10 *a 1.795,2.729 1.997,2.927 0.202,0.198 10 *b 2.752,2.729 2.954,2.927 0.202,0.198 10 *c 0.569,0.498 0.771,0.696 0.202,0.198 10 *d 2.711,0.498 2.914,0.696 0.202,0.198 10 *e 1.772,0.498 1.974,0.696 0.202,0.198 10 *e
*a Normal
*b Protruding
*c Deformed
*d Correct
*e Incorrect


After installing the fuel injector seals, check that they are not scratched, deformed or protruding from the fuel injector assembly groove.

NOTICE:

If a fuel injector seal is scratched, deformed or protruding from the groove, replace it with a new one.



Hide 23250 2.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


a.
A335645C01
1.052,0.427 1.229,0.427 1.229,0.427 1.51,0.927 false 2.302,0.396 2.479,0.396 2.479,0.396 2.615,0.635 false 2.531,0.208 2.708,0.208 2.708,0.208 2.844,0.448 false 2.885,0.094 3.01,0.094 3.01,0.094 3.01,0.49 true 0.865,0.365 1.177,0.521 0.313,0.156 10 false *1 2.115,0.323 2.427,0.479 0.313,0.156 10 false *2 2.354,0.135 2.667,0.292 0.313,0.156 10 false *3 2.708,0.01 3.021,0.167 0.313,0.156 10 false *a
*1 Fuel Injector Assembly
*2 C-ring
*3 Injector Vibration Insulator
*a Taper


Install a new injector vibration insulator and a new C-ring to the fuel injector assembly.

NOTICE:
·

Install the taper of the injector vibration insulator by aligning it with the taper of the fuel injector assembly.

·

Check that the C-ring is securely seated in the groove of the fuel injector assembly.




b.

Install a new O-ring and a new No. 1 fuel injector back-up ring to the fuel injector assembly as shown in the illustration.

A304564C01
5.917,1.708 6.208,1.135 6.208,1.135 6.354,1.135 true 4.99,1.188 5.208,1.188 5.208,1.188 5.625,1.781 true 4.781,1.104 5.094,1.26 0.313,0.156 10 false *1 6.417,1.052 6.729,1.208 0.313,0.156 10 false *2 1.583,0.563 1.896,0.719 0.313,0.156 10 false *a 0.76,1.875 1.073,2.031 0.313,0.156 10 false *b 2.552,1.875 2.865,2.031 0.313,0.156 10 false *c 1.604,1.073 1.917,1.229 0.313,0.156 10 false *d 0.76,1.073 1.073,1.229 0.313,0.156 10 false *e 2.531,1.063 2.844,1.219 0.313,0.156 10 false *e
*1 No. 1 Fuel Injector Back-up Ring *2 O-ring
*a No. 1 Fuel Injector Back-up Ring Opening *b Overlapped
*c Stretched *d Correct
*e Incorrect - -


NOTICE:
·

Check that there is no foreign matter or damage on the O-ring groove of the fuel injector assembly.

·

Make sure that the No. 1 fuel injector back-up ring is installed in the correct orientation.

·

Make sure that the No. 1 fuel injector back-up ring and O-ring are installed in the correct order.

·

Check that the opening of the No. 1 fuel injector back-up ring is not overlapped or stretched as shown in the illustration.

·

After installing the O-ring, check that it is not contaminated with foreign matter and is not damaged.




c.
A273121C03
3,2.188 2.927,2.188 2.927,2.188 2.74,2.375 false 3.031,1.438 2.979,1.438 2.979,1.438 2.854,1.573 false 2.479,2.448 2.729,2.813 2.729,2.813 2.823,2.813 true 3.052,1.354 3.24,1.573 0.188,0.219 10 false *1 3.052,2.125 3.24,2.344 0.188,0.219 10 false *2 2.844,2.729 3.031,2.906 0.188,0.177 10 false *a
*1 Fuel Injector Assembly
*2 No. 3 Fuel Injector Back-up Ring
*a Notch


With the notch of a new No. 3 fuel injector back-up ring facing downward, install the fuel injector assembly to the No. 3 fuel injector back-up ring as shown in the illustration.

NOTICE:
·

Make sure that the No. 3 fuel injector back-up ring is installed in the correct orientation.

·

After installing the No. 3 fuel injector back-up ring, make sure there is no damage or foreign matter.




d.

Install the nozzle holder clamp to each fuel injector assembly.


e.
A273091C03
2.344,0.135 2.208,0.135 2.208,0.135 1.854,0.344 true 1.927,0.698 2.521,1.792 2.521,1.792 2.604,1.792 true 2.375,0.063 2.583,0.24 0.208,0.177 10 *a 2.656,1.74 2.865,1.917 0.208,0.177 10 *b
*a Protrusion
*b Positioning Hole
V100135

No Gap


Align the protrusion of the nozzle holder clamp with the positioning hole of the fuel delivery pipe and insert the fuel injector assembly.

NOTICE:
·

Make sure that there is no foreign matter or damage inside the fuel injector assembly installation holes (fuel delivery pipe).

·

Do not allow gasoline to get on the O-rings or inside the installation holes.

·

If it is difficult to insert the fuel injector assembly, apply new engine oil to the chamfer of the fuel injector assembly installation hole of the fuel delivery pipe. Be careful not to allow the fuel injector assembly to fall out of the fuel delivery pipe.

·

Do not tilt the fuel injector assembly when inserting it into the fuel delivery pipe.

A326487C03
0.115,0.104 3.083,2.667 2.969,2.563 3.25,0.104 6.667,2.667 3.417,2.563 2.25,1.083 2.417,1.5 2.417,1.5 2.583,1.5 true 5.417,1.083 5.583,1.5 5.583,1.5 5.75,1.5 true 1.313,1 1.313,1.417 false 4.333,0.771 4.333,1.104 false 0.24,0.167 0.552,0.365 0.313,0.198 10 false *a 3.354,0.167 3.667,0.365 0.313,0.198 10 false *b 1.24,1.448 1.552,1.646 0.313,0.198 10 false *1 4.281,1.125 4.594,1.323 0.313,0.198 10 false *1 2.635,1.427 2.948,1.625 0.313,0.198 10 false *2 5.802,1.427 6.115,1.625 0.313,0.198 10 false *2
*1 O-ring *2 Fuel Delivery Pipe
*a Correct *b Incorrect


·

Check that there is no gap between the fuel delivery pipe and the nozzle holder clamp.

·
A300515C02
0.917,1.031 1.229,1.031 1.229,1.031 1.688,1.573 true 0.781,2.042 1.01,2.042 1.01,2.042 1.479,1.677 true 0.74,0.958 1.052,1.115 0.313,0.156 10 *a 0.615,1.969 0.927,2.125 0.313,0.156 10 *b
*a QR Code
*b Flow Classification Number


Make sure the 4 fuel injector assemblies have the same flow classification number 1, 2 or 3 (the number to the left of the QR code).




Hide 23814B 3.INSTALL FUEL DELIVERY PIPE

a.

w/ Stud Bolt:

i.

Apply lubricant to the fuel injector assembly installation holes of the cylinder head sub-assembly.


ii.
A186827C06
2.729,0.313 2.667,0.313 2.667,0.313 2.302,0.5 false 2.75,0.219 2.927,0.375 0.177,0.156 10 *a
*a Protruding enough to install nut


Temporarily install the fuel delivery pipe so that the stud bolts protrude enough to install the nuts.

NOTICE:
·

If a fuel injector assembly is dropped or the tip of a fuel injector assembly is struck, replace it with a new one.

·

Check that there is no foreign matter or damage on the fuel injector assembly installation holes of the cylinder head sub-assembly.

·

When installing the fuel delivery pipe, push it in evenly without tilting it.




iii.
A350911C04
1.385,1.156 1.49,1.292 0.104,0.135 10 true 1 0.854,1.24 0.979,1.375 0.125,0.135 10 true 2 2.448,0.979 2.552,1.125 0.104,0.146 10 true 3 0.188,1.323 0.313,1.469 0.125,0.146 10 true 4 2.917,0.813 3.021,0.948 0.104,0.135 10 true 5
V100135

Bolt
V100136

Nut


Install the fuel delivery pipe by uniformly tightening the 3 bolts and 2 nuts in the order shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)



b.

w/o Stud Bolt:

i.

Apply lubricant to the fuel injector assembly installation holes of the cylinder head sub-assembly.


ii.
A414028

Temporarily install the fuel delivery pipe to the cylinder head sub-assembly with the 2 bolts.

NOTICE:
·

If a fuel injector assembly is dropped or the tip of a fuel injector assembly is struck, replace it with a new one.

·

Check that there is no foreign matter or damage on the fuel injector assembly installation holes of the cylinder head sub-assembly.

·

When installing the fuel delivery pipe, push it in evenly without tilting it.



HINT:
A414029C03
0.552,1.219 0.865,1.375 0.313,0.156 10 false *a
*a 2 to 3 threads


Install the 2 bolts by 2 to 3 threads.



iii.
A414030C03
0.469,3.49 0.781,3.646 0.313,0.156 10 false *a
*a No Gap
V100135

Push


Push the fuel delivery pipe until it contacts the cylinder head sub-assembly.

NOTICE:

Make sure that there is no gap between the fuel delivery pipe and cylinder head sub-assembly.



iv.
A414027N01
1.448,1.229 1.594,1.406 0.146,0.177 10 true 1 0.979,1.323 1.125,1.479 0.146,0.156 10 true 2 2.333,1.115 2.49,1.281 0.156,0.167 10 true 3 0.281,1.365 0.427,1.521 0.146,0.156 10 true 4 2.813,1.01 2.948,1.167 0.135,0.156 10 true 5

Install the fuel delivery pipe by uniformly tightening the 5 bolts in the order shown in the illustration.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)



Hide 82124 4.CONNECT NO. 4 ENGINE WIRE

a.

Connect the fuel pressure sensor connector.


b.

Connect the 4 fuel injector assembly connectors.


Hide 23801P 5.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23801P 6.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 9. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic leaning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 11.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing a fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION