Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › TRANSFER CASE FRONT OIL SEAL (for LH Side) › from 2020.08
RM32H0E _52 Drivetrain _059725 GF1A TRANSFER / 4WD / AWD _0292790 TRANSFER CASE FRONT OIL SEAL(for LH Side) A

GF1A TRANSFER / 4WD / AWD  TRANSFER CASE FRONT OIL SEAL(for LH Side)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the transfer case oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION / NOTICE / HINT

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 36100 1.REMOVE TRANSFER ASSEMBLY

Hide 36100A 2.REMOVE TRANSFER AND TRANSAXLE SETTING STUD BOLT

Hide 36111B 4.REMOVE TRANSFER CASE OIL SEAL

a.
C360082C01
0.635,0.844 1.052,0.427 true 2.188,1.865 2.406,1.313 true 0.448,0.75 0.76,0.906 0.313,0.156 10 false *1 1.844,1.76 2.229,1.948 0.385,0.188 10 false SST
*1 Transfer Case Oil Seal


Using SST, remove the transfer case oil seal from the transfer case.

SST
09308-00010  

NOTICE:
·

Do not scratch the press-fitting surface of the transfer case oil seal.

·

Wear or damage to the front drive shaft oil seal RH on the transmission side will cause transfer oil leakage.

If it is worn or damaged, replace the front drive shaft oil seal RH.

Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>FRONT DIFFERENTIAL OIL SEAL (for RH Side)>REPLACEMENT




Hide 36111B 5.INSTALL TRANSFER CASE OIL SEAL

a.

Coat the lip of a new transfer case oil seal with MP grease.


b.
C360078C01
0.719,3.938 1.385,3.438 true 0.917,0.75 1.427,1.333 true 0.531,3.833 0.844,3.99 0.313,0.156 10 false *1 0.573,0.646 0.969,0.813 0.396,0.167 10 false SST 0.635,2.99 1.094,3.188 0.458,0.198 10 false (A)
*1 Transfer Case Oil Seal


Using SST and a hammer, tap in a new transfer case oil seal as shown in the illustration.

SST
09316-60011  (09316-00011)

Drive in depth (A):

9.5 to 10.5 mm (0.375 to 0.413 in.)


NOTICE:
·

Tap the transfer case oil seal uniformly so that the transfer case oil seal is straight.

·

Do not tap the transfer case oil seal in too far.




Hide 36100 6.REMOVE TRANSFER ASSEMBLY

Hide 36100A 7.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

Hide 36100 8.INSTALL TRANSFER ASSEMBLY