If the forward recognition camera detects a short +B in the buzzer circuit, it will store DTC C1A4A12.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A4A12 | Buzzer Circuit Short to Battery | While the pre-collision city buzzer is sounding, the forward recognition camera detects a short to +B in the buzzer circuit for 2 seconds or more. | ·
Pre-collision city buzzer ·
Forward recognition camera ·
Wire harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT
Clear the DTCs.
Perform the Active Test according to the display on the GTS.
Perform the Active Test for 2 seconds or more.
Performing the Active Test for 2 seconds or more causes DTC C1A4A12 to be stored if the DTC detection conditions are met.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| PCS Warning Buzzer | Sounds the pre-collision city buzzer | Start / Stop | Test possible with ignition switch ON, vehicle stopped |
| Tester Display |
|---|
| PCS Warning Buzzer |
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A4A12 is not output | A |
| DTC C1A4A12 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the F54 pre-collision city buzzer connector.
Disconnect the R5 forward recognition camera connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F54-1 (BZ) or R5-8 (BZ) - Body ground | Ignition switch off | Below 1 V |
Connect the R5 forward recognition camera connector.
Connect the F54 pre-collision city buzzer connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the pre-collision city buzzer.
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>REMOVAL
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER (for RHD)>REMOVAL
Inspect the pre-collision city buzzer.
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>INSPECTION
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER (for RHD)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>REMOVAL
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER (for RHD)>REMOVAL