If the forward recognition camera detects an open or short to ground in the buzzer circuit, it will store DTC C1A4A14.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A4A14 | Buzzer Circuit Short to Ground or Open | The forward recognition camera detects an open or short to ground in the buzzer circuit for 2 seconds or more. | ·
Pre-collision city buzzer ·
Forward recognition camera ·
Wire harness or connector |
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT
Clear the DTCs.
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A4A14 is not output | A |
| DTC C1A4A14 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
| *a | Front view of wire harness connector
(to Pre-collision City Buzzer) |
Disconnect the pre-collision city buzzer connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F54-2 (IG1) - Body ground | Ignition switch ON | 8 to 16 V |
| Ignition switch off | Below 1 V |
Connect the pre-collision city buzzer connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F54 pre-collision city buzzer connector.
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F54-1 (BZ) - R5-8 (BZ) | Always | Below 1 Ω |
| F54-1 (BZ) or R5-8 (BZ) - Body ground | Always | 10 kΩ higher |
Connect the R5 forward recognition camera connector.
Connect the F54 pre-collision city buzzer connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the pre-collision city buzzer.
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>REMOVAL
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER (for RHD)>REMOVAL
Inspect the pre-collision city buzzer.
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>INSPECTION
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER (for RHD)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER(for LHD)>REMOVAL
for RHD: Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT BUZZER (for RHD)>REMOVAL