The purpose of this circuit is to prevent the engine from stalling when the brakes are suddenly applied while driving with lock-up on.
When the brake pedal is depressed, stop light switch assembly sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P070312 | Brake Switch "B" Circuit Short to Battery | Stop light switch remains on even when the vehicle is driven in a stop (less than 3 km/h (1.86 mph)) and go (30 km/h (18.65 mph) or more) pattern 5 times (2 trip detection logic). | ·
Short in stop light switch assembly circuit ·
Stop light switch assembly ·
ECM |
Comes on | DTC stored | SAE Code:
P0724 |
This DTC indicates that the stop light switch is remaining on. When the stop light switch remains on during "stop and go" driving, the ECM interprets this as a malfunction of the stop light switch assembly, illuminates the MIL and stores this DTC. The vehicle must STOP (less than 3 km/h (2 mph)) and GO (30 km/h (19 mph) or more) five times for two consecutive driving cycles in order to store this DTC.
Refer to SFI system DTC P05042B.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P05042B
Perform initialization when parts related to the continuously variable transaxle are replaced.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Inspect the fuses for circuits related to this system before performing the following procedure.
Using the GTS, the Data List item "Stop Light SW" can be read.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DATA LIST / ACTIVE TEST
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Perform the following stop and go drive pattern 5 times:
Perform the following procedure while strictly observing all traffic laws and speed limits.
Accelerate the vehicle to 30 km/h (18.65 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less.
Turn the ignition switch off.
Perform step (a) again.
Check for DTCs again.
Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List / Stop Light SW.
| Tester Display |
|---|
| Stop Light SW |
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch status | OFF or ON | ·
OFF: Brake pedal released ·
ON: Brake pedal depressed |
- |
On the GTS screen, ON or OFF is displayed accordingly.
In the table above, the conditions listed under "Normal Condition" are reference conditions. Do not depend solely on these reference conditions when deciding whether a part is faulty or not.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the stop light switch assembly installation.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION
Stop light switch assembly is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ECM connector.
| *a | Brake pedal depressed | *b | Brake pedal released |
| *c | Front view of wire harness connector
(to ECM) |
- | - |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A38-9 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| Brake pedal depressed | 7.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT