Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › from 2020.08
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292321 TRANSMISSION CONTROL CABLE A

EC6A MANUAL TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the transmission control cable assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)

CAUTION:
·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Air conditioning system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
·
C332327

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to neutral, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 28800 4.REMOVE BATTERY

Hide 5.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 53141F 6.REMOVE RADIATOR COVER

Hide 17751 7.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17701 9.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 57533B 12.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 13.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 58151 14.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

a.
C364049

Remove 3 nuts and front No. 1 floor heat insulator from the vehicle body.


Hide 33820B 15.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C365818

Remove the clip to disconnect the transmission control select cable from the floor shift shift lever assembly.


b.
C365819

Disconnect the transmission control shift cable from the floor shift shift lever assembly.


c.
C365820

Disengage the 2 claws and disconnect the transmission control cable assembly from the floor shift lever assembly.


d.
C356470N01
1.708,1.438 1.865,1.635 0.156,0.198 10 true A 1.51,1.938 1.667,2.135 0.156,0.198 10 true A 2.344,0.5 2.5,0.698 0.156,0.198 10 true B 1.104,0.052 1.26,0.25 0.156,0.198 10 true B

Remove the 2 clips A to disconnect the transmission control cable assembly from the manual transaxle assembly.


e.

Remove the 2 clips B to disconnect the transmission control cable assembly from the control cable bracket assembly.


f.
C365821

Remove the nut.


g.

Disengage the guide and disconnect the transmission control cable assembly from the vehicle body.


h.
C365822

Remove the 2 nuts and transmission control cable assembly from the vehicle body.


Hide 16. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART