Home › Engine / Hybrid System › 3ZR-FAE (FUEL) › FUEL SYSTEM › from 2020.08
RM32H0E _51 Engine / Hybrid System _060184 3ZR-FAE FUEL _0295032 FUEL SYSTEM G

3ZR-FAE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

v.

Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sound can be heard, check the fuel pump, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the ignition switch off.


d.

Disconnect the GTS from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Measure the battery voltage.

Standard Voltage:

11 to 14 V



c.

Disconnect the cable from the negative (-) battery terminal.

Click hereGeneral>MAINTENANCE>3ZR-FAE BATTERY>REMOVAL

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



d.
A310731

Disengage the claw and remove the No. 1 fuel pipe clamp.


e.

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


f.
A349783C03
0.583,1.417 0.75,1 0.75,1 0.917,1 false 1.583,2.417 1.75,2.417 1.75,2.417 2,2.021 false 2.417,0.5 2.583,0.5 2.583,0.5 2.813,0.344 false 2.25,1.083 2.417,1.083 2.417,1.083 2.667,0.927 false 2.333,1.417 2.5,1.417 2.5,1.417 2.729,1.521 false 2.635,2.917 2.917,2.667 2.917,2.667 3.083,2.667 false 0.667,3.333 0.833,3.333 0.833,3.333 1.083,3.104 false 0.667,4.083 0.833,4.083 0.833,4.083 1.135,3.917 false 0.958,0.917 1.271,1.073 0.313,0.156 10 false *a 1.406,2.333 1.719,2.49 0.313,0.156 10 false *b 3.104,2.583 3.333,2.75 0.229,0.167 10 false *c 2.083,1 2.396,1.156 0.313,0.156 10 false *d 0.5,4 0.813,4.156 0.313,0.156 10 false *e 2.25,0.417 2.563,0.573 0.313,0.156 10 false *f 2.167,1.333 2.479,1.49 0.313,0.156 10 false *f 0.5,3.26 0.813,3.417 0.313,0.156 10 false *f
*a SST (Pressure Gauge)
*b SST (Hose Joint)
*c SST (Hose)
*d SST (T-joint)
*e SST (Fuel Tube Connector)
*f SST (Hose Band)


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-00010  (09268-00020, 09268-00030)
09268-45101  (09268-41260, 09268-41280, 09268-41700, 95336-08070)


g.

Wipe up any spilled fuel.


h.

Connect the cable to the negative (-) battery terminal.

Click hereGeneral>MAINTENANCE>3ZR-FAE BATTERY>INSTALLATION


i.

Initialization after reconnecting battery terminal.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART



j.

Connect the GTS to the DLC3.


k.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

l.

Measure the fuel pressure.

Standard Fuel Pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


·

If the fuel pressure is greater than the standard, replace the fuel pressure regulator assembly.

·

If the fuel pressure is less than the standard, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator assembly.



m.

Disconnect the GTS from the DLC3.


n.

Start the engine.


o.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


HINT:

Standard idle speed.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



p.

Stop the engine.


q.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Standard Fuel Pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or more


If the fuel pressure is not as specified, check the fuel pump, fuel pressure regulator assembly and/or fuel injector assemblies.


r.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST (EFI fuel pressure gauge) to prevent fuel from spraying.

Click hereGeneral>MAINTENANCE>3ZR-FAE BATTERY>REMOVAL

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



s.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL SYSTEM>PRECAUTION


t.

Engage the claw and install the No. 1 fuel pipe clamp.