Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › from 2020.08
RM32H0E _58 Vehicle Interior _059647 DOOR LOCK _0292600 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 69730E 1.INSTALL NO. 1 REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.
B450682

Engage the guide to install the No. 1 rear door lock remote control cable assembly to the rear door lock with motor assembly.


b.
B450695C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


Hide 69780B 2.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

a.

w/o Double Locking System:

i.
B450684

Engage the guide to install the rear door inside locking cable assembly to the rear door lock with motor assembly.


ii.
B450693C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.



b.

w/ Double Locking System:

i.
B450688

Engage the guide to install the rear door inside locking cable assembly to the rear door lock with motor assembly.


ii.
B450696C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.



Hide 69740D 3.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

a.

w/ Double Locking System:

i.
B450680

Engage the guide to install the rear door lock remote control cable assembly to the rear door lock with motor assembly.


ii.
B450694C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.



b.

w/ Double Locking System:

i.
B450686

Engage the guide to install the rear door lock remote control cable assembly to the rear door lock with motor assembly.


ii.
B450697C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw as shown in the illustration.



Hide 69060A 4.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

NOTICE:
·

When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.

·

Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

·

Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.



a.

Apply MP grease to the sliding parts of the rear door lock with motor assembly.


b.

When reusing the rear door lock with motor assembly:

i.

Install a new door lock wiring harness seal to the rear door lock with motor assembly.



c.
B450677C01
0,0 0,0 false
V113147

Install in this Direction


Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


d.

Connect the connector.


Hide 69240 5.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

Hide 69227L 6.INSTALL REAR DOOR OUTSIDE HANDLE COVER

Hide 67842E 7.INSTALL REAR DOOR SERVICE HOLE COVER

Hide 67628 8.INSTALL REAR DOOR TRIM BRACKET

Hide 67604 9.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 84810 10.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

Hide 69284D 11.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

Hide 67498 12.INSTALL REAR DOOR REAR FRAME BRACKET

Hide 13.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 14. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 15. INITIALIZE POWER WINDOW CONTROL SYSTEM