Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
75988E
1.INSTALL REAR DOOR OUTSIDE STRIPE (w/ Stripe Tape)
75978H
2.INSTALL REAR DOOR LOWER OUTSIDE STRIPE (w/ Stripe Tape)
75766A
3.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING
75764A
4.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING
75742
5.INSTALL REAR DOOR OUTSIDE MOULDING
75076
6.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY
67003C
7.INSTALL REAR DOOR PANEL CUSHION
Engage the claws to install the 2 rear door panel cushions.
86160B
8.INSTALL REAR SPEAKER ASSEMBLY
67837C
9.INSTALL REAR DOOR DUST PROOF SEAL (for TMMT Made)
Install the 3 rear door dust proof seals.
67837C
10.INSTALL REAR DOOR DUST PROOF SEAL (for TMC Made)
Install the 2 rear door dust proof seals.
Even if there were 3 dust proof seals at the time of removal, install 2 dust proof seals as shown in the illustration.
69060A
11.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY
69229A
12.INSTALL NO. 3 DOOR OUTSIDE HANDLE CAP
|
Install in this Direction |
Engage the claws to install the 2 No. 3 door outside handle caps.
69240
13.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
Engage the guide to connect the No. 1 rear door lock remote control cable assembly.
Engage the claws to install the rear door outside handle assembly.
Install the 3 bolts.
Connect the No. 1 rear door lock remote control cable assembly to the clamps.
69227L
14.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Clean the rear door outside handle assembly surface.
Remove the release paper from the face of the rear door outside handle cover.
|
Double-sided Tape |
Engage the clips and guide to install a new rear door outside handle cover.
Press the double-sided tape area of the rear door outside handle cover.
75740
15.INSTALL REAR DOOR BELT MOULDING ASSEMBLY
68189
16.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP
Install the rear door quarter window weatherstrip to the rear door quarter window glass.
68124B
17.INSTALL REAR DOOR QUARTER WINDOW GLASS
|
Install in this Direction |
Install the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.
18.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY
Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.
| *a | Temporary Bolt |
Temporarily install the temporary bolt to the rear door window regulator sub-assembly.
Temporarily install the rear door window regulator sub-assembly with the 3 bolts.
Tighten the temporary bolt and 3 bolts to install the rear door window regulator sub-assembly.
Tighten the bolts in the order shown in the illustration.
Connect the connector.
68152C
19.INSTALL REAR DOOR GLASS RUN
Install the rear door glass run.
67674A
20.INSTALL REAR DOOR FRAME GARNISH
Engage the guides to install the rear door frame garnish.
69975A
21.INSTALL REAR DOOR GLASS CHANNEL FILLER (for LED Type Turn Signal Light)
Apply soapy water to a new rear door glass channel filler.
| *A | Front Side |
| *B | Rear Side |
| *a | Edge of curved surface |
Install the rear door glass channel filler to the rear door glass sub-assembly at position shown in the illustration.
| Area | Measurement |
|---|---|
| A | 10 mm (0.394 in.) |
| B | 10 mm (0.394 in.) |
69906B
22.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY (for LED Type Turn Signal Light)
Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.
| *A | Front Side |
| *B | Rear Side |
| *a | Edge of curved surface |
Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.
| Area | Measurement |
|---|---|
| A | 10 mm (0.394 in.) |
| B | 10 mm (0.394 in.) |
To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.
68104
23.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Insert the rear door glass sub-assembly as shown in the illustration.
Do not damage the rear door glass sub-assembly.
|
Install in this Direction |
Install the rear door glass sub-assembly to the rear door window regulator sub-assembly as shown in the illustration.
67408F
24.INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY
Temporarily install the rear door window rear lower frame sub-assembly with the 2 bolts.
Install the screw.
Tighten the 2 bolts.
Connect the rear door glass run.
67868D
25.INSTALL REAR DOOR WEATHERSTRIP
Clean the rear door panel.
Remove the release paper from a new rear door weatherstrip.
| *a | Clip (A) |
|
Double-sided Tape |
Engage the clip (A) and other clip to install the rear door weatherstrip.
Press the double-sided tape area of the rear door weatherstrip.
68640A
26.INSTALL REAR DOOR CHECK ASSEMBLY
Clean the bolt hole in the vehicle body.
Clean the threads of the bolt (A).
Apply adhesive to the threads of the bolt (A).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
| *a | Bolt (A) |
| *b | Bolt (B) |
Install the rear door check assembly with the bolt (A) and 2 bolts (B).
67842E
27.INSTALL REAR DOOR SERVICE HOLE COVER
| *a | Reference Point |
|
Butyl Tape |
Apply new butyl tape to the rear door panel.
Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.
Install the front door service hole cover according to the reference points on the front door panel.
Securely install the rear door service hole cover preventing wrinkles and air bubbles.
67628
28.INSTALL REAR DOOR TRIM BRACKET
Install the rear door trim bracket with the 2 screws.
67676C
29.INSTALL NO. 2 REAR DOOR FRAME GARNISH
Install the No. 2 rear door frame garnish.
30.INSTALL HOLE PLUG
Install the 2 hole plugs.
68197
31.INSTALL REAR DOOR BELT SEAL
|
Install in this Direction |
Install the rear door belt seal to the rear door glass inner weatherstrip as shown in the illustration.
68174A
32.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP
|
Install in this Direction |
Install the rear door glass inner weatherstrip with the rear door belt seal as shown in the illustration.
68199
33.INSTALL REAR DOOR BELT REAR SEAL
Install the rear door belt rear seal.
69206C
34.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the guides and claw to install the front door inside handle sub-assembly.
67604
35.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
|
Install in this Direction |
Engage the guides to connect the rear door inside locking cable assembly and rear door lock remote control cable assembly.
|
Install in this Direction |
Engage the claws as shown in the illustration.
Engage the guide and clips to install the rear door trim board sub-assembly.
Install the 2 screws.
Install the 3 screws.
84810D
36.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL
Connect the connector.
|
Install in this Direction |
Engage the guides, clips and claws to install the rear power window regulator switch assembly with rear door armrest base upper panel as shown in the illustration.
69284D
37.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
|
Install in this Direction |
Engage the claws to install the rear door inside handle bezel plug as shown in the illustration.
67498
38.INSTALL REAR DOOR REAR FRAME BRACKET
|
Install in this Direction |
Engage the claws and clip to install the rear door rear frame bracket as shown in the illustration.
39.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
for 8NR-FTS:
for 3ZR-FAE:
40. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
41. INITIALIZE POWER WINDOW CONTROL SYSTEM
42.INSPECT POWER WINDOW OPERATION