Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P137800  Pre-ignition Detected  


DESCRIPTION

If sudden early ignition (pre-ignition) occurs continuously in a short period of time, a DTC is stored. Pre-ignition is a phenomenon inherent to small displacement forced-induction engines. Atomized engine oil and detached deposits (carbon) can cause pre-ignition and promote engine knocking during low-speed, high-output operation. This is higher pressure knocking than normal knocking.

Pre-ignition is detected by the knock sensor.

When pre-ignition occurs, the ECM limits output to suppress the pre-ignition. If pre-ignition occurs continuously, fuel cut may be performed in some situations, which may cause vehicle behavior similar to hesitation or shift shock. This is not a malfunction.

As pre-ignition cannot be detected if a knock sensor malfunction occurs, the same fail-safe control occurs as for strong knock detection.

HINT:
·

When this DTC is stored, the ECM enters fail-safe mode.

·

During fail-safe mode, the ECM limits the output.

·

Fail-safe mode continues until a pass condition is detected.



DTC No. Detection Item DTC Detection Condition MIL Memory Note
P137800 Pre-ignition Detected Continuous pre-ignition prevention fuel cut control is performed twice (1 trip detection logic).
Continuous pre-ignition prevention fuel cut control operation conditions: Sudden early ignition (pre-ignition) occurs 5 times or more continuously in a short period of time.
Does not come on DTC stored SAE Code: P1378

Trouble Area
Ignition system
·

Ignition malfunction of No. 1 ignition coil or spark plug


Fuel injection system
·

Decrease in fuel injection volume


Lubrication system
·

High oil consumption

·

Dilute / deteriorated oil

·

Additive


Fuel system
·

Diesel fuel contamination

·

Addition of fuel additives

·

Fuel pump assembly

·

Low quality fuel


Engine related
·

Accumulated deposit (in combustion chamber)


Intake system
·

Air leaks


Exhaust system
·

Clogged exhaust system component



HINT:
·

As strong knocking due to pre-ignition may be caused by multiple superimposed factors, it is important to comprehensively investigate all possible causes.

·

The risk of this occurring is increased if driving up a steep incline while towing in a low gear, as low-speed, high-output operation occurs.



CAUTION / NOTICE / HINT

HINT:
·

If the customer reports a knocking sound or drivability problems, check the value of Data List items "Consecutive Prevention Cylinder #1 History" through "Consecutive Prevention Cylinder #4 History".

·

If the distance traveled recorded in the Data List subtracted from the value of Distance for Control is equal to the customer reported mileage of the vehicle when control occurred subtracted from the current vehicle mileage, explain to the customer that this condition is due to normal control to prevent pre-ignition and not a malfunction.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P137800)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P137800 is output A
DTC P137800 and other DTCs are output B


HINT:

If any DTCs other than P137800 are output, troubleshoot those DTCs first.




A

2.READ FREEZE FRAME DATA

B

2.READ FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

HINT:
·

Check the freeze frame data sets recorded the moment the DTC was stored and after the DTC was stored.

·

Using the freeze frame data, confirm the vehicle conditions when the DTC was stored, such as if the engine was idling with the shift lever in P, D or N (neutral) or if the vehicle was being driven at a constant speed or accelerating.


Confirmation Item
Vehicle Speed Short FT Bank 1
Engine Speed Long FT Bank 1
Vehicle Load Fuel System Status Bank 1
Coolant Temperature Misfire Count Cylinder #1 to #4



Result:
Proceed to
NEXT



NEXT

3.READ VALUE USING GTS (CONSECUTIVE PREVENTION CYLINDER AND FUEL CUT HISTORY)
3.READ VALUE USING GTS (CONSECUTIVE PREVENTION CYLINDER AND FUEL CUT HISTORY)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Consecutive Prevention Cylinder #1 History 1 to Consecutive Prevention Cylinder #4 History 4, Fuel Cut History 1 to Fuel Cut History 4

Powertrain > Engine > Data List
Tester Display
Consecutive Prevention Cylinder #1 History 1
Consecutive Prevention Cylinder #1 History 2
Consecutive Prevention Cylinder #1 History 3
Consecutive Prevention Cylinder #1 History 4
Consecutive Prevention Cylinder #2 History 1
Consecutive Prevention Cylinder #2 History 2
Consecutive Prevention Cylinder #2 History 3
Consecutive Prevention Cylinder #2 History 4
Consecutive Prevention Cylinder #3 History 1
Consecutive Prevention Cylinder #3 History 2
Consecutive Prevention Cylinder #3 History 3
Consecutive Prevention Cylinder #3 History 4
Consecutive Prevention Cylinder #4 History 1
Consecutive Prevention Cylinder #4 History 2
Consecutive Prevention Cylinder #4 History 3
Consecutive Prevention Cylinder #4 History 4
Fuel Cut History 1
Fuel Cut History 2
Fuel Cut History 3
Fuel Cut History 4
50003 372 312,313,314,315,316,317,318,319,320,321,322,323,324,325,326,327,328,329,330,331

e.

According to the freeze frame data, attempt to reproduce the vehicle conditions that were present when the DTC was stored and read the Data List.


Result:
Result Proceed to
Values are displayed for multiple consecutive prevention cylinder histories of a specific cylinder A
Values are displayed for multiple consecutive prevention cylinder histories of all cylinders B


HINT:
·

If values are displayed for multiple consecutive prevention cylinder histories of a specific cylinder, check the value of freeze frame data items Misfire Count Cylinder #1 through #4. If the misfire count of that cylinder is high, the cylinder is malfunctioning.

·

If the vehicle conditions when the DTC was stored cannot be reproduced, read the value of freeze frame data items Misfire Count Cylinder #1 through #4 to determine if only a specific cylinder or all cylinders are malfunctioning.




A

4.CHECK IGNITION SYSTEM

B

6.READ VALUE USING GTS (SHORT FT B1S1 AND LONG FT B1S1)
4.CHECK IGNITION SYSTEM
a.

Check the ignition system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

Interchange the ignition coil assembly and spark plug of the malfunctioning cylinder with those of a known good cylinder and according to the freeze frame data, check if the malfunctioning cylinder returns to normal.

·

Read the Data List items Misfire Count Cylinder #1 to #4 while performing this procedure to determine which cylinder is malfunctioning.




Result:
Result Proceed to
The malfunctioning cylinder returns to normal A
The malfunctioning cylinder does not return to normal B



A

35.REPAIR OR REPLACE MALFUNCTIONING PARTS

B

5.INSPECT OTHER RELATED COMPONENTS
5.INSPECT OTHER RELATED COMPONENTS
a.

Check the power source circuit, wire harness and connectors.


Result:
Proceed to
NEXT



NEXT

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
6.READ VALUE USING GTS (SHORT FT B1S1 AND LONG FT B1S1)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Short FT B1S1 and Long FT B1S1.

Powertrain > Engine > Data List
Tester Display
Short FT B1S1
Long FT B1S1
50003 372 207,209

e.

According to the freeze frame data, attempt to reproduce the vehicle conditions that were present when the DTC was stored and read the Data List.

Result:
Data List Result Proceed to
Short FT B1S1 + Long FT B1S1 -15% or higher, or less than 15% A
Other than above B


HINT:
·

If the vehicle conditions when the DTC was stored cannot be reproduced, read the value of freeze frame data items Short FT B1S1 and Long FT B1S1 to perform judgment.

·

"Total FT Bank 1" is used to detect an abnormal air fuel ratio. As the value of "Total FT Bank 1" is corrected by the ECM before it is displayed in the Data List, the displayed value may not be equal to the sum of the measured "Short FT B1S1" and "Long FT B1S1".

·

An abnormally lean or rich tendency can be checked by reading the following Data List items: A/F Learn Value Idle Bank 1, A/F Learn Value Low Bank 1, A/F Learn Value Mid No. 1 Bank 1, A/F Learn Value Mid No. 2 Bank 1, A/F Learn Value High Bank 1, .

·

The following may cause a lean air fuel ratio (an operating range in which the air fuel ratio learned value correction is +15% or more):

(a)

Decrease in fuel injector assembly injection volume

(b)

Decrease in mass air flow meter output (due to existence of foreign matter)

(c)

Air leaks in intake system after mass air flow meter

(d)

Decrease in fuel pressure (at fuel filter, fuel pump, fuel main valve assembly or fuel suction plate sub-assembly)


·

On vehicles which the learning value for each operating range can be checked, if the value of "A/F Learn Value High Bank 1" only is corrected to the positive side, a malfunction in the fuel system (clogging of the fuel pump or fuel filter) is suspected.

·

On vehicles which the learning value for each operating range can be checked, if the value of "A/F Learn Value Idle Bank 1", "A/F Learn Value Low Bank 1" only is corrected to the positive side, an air leak after the mass air flow meter is suspected.

·

The following may cause a rich air fuel ratio (an operating range in which the air fuel ratio learned value correction is -15% or less):

(a)

Increase in the fuel injector assembly injection volume

(b)

Purge VSV system






A

7.INTERVIEW THE CUSTOMER

B

11.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
7.INTERVIEW THE CUSTOMER
a.

Interview the customer for details about when oil maintenance was last performed and what brand of oil was used.

i.

Check whether the specified engine oil grade was used and that engine oil additives were not used.


ii.

Perform an engine oil inspection (check the oil level and for dirt, etc.).

Click hereEngine / Hybrid System>8NR-FTS (LUBRICATION)>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION



OK:

No problem with the engine oil.


HINT:
·

Strong knocking due to pre-ignition may be due to ignition of atomized engine oil under certain conditions.

·

The risk of this occurring may be increased if the engine oil used is not the specified oil grade.

·

The risk of this occurring may be increased if engine oil additives have been used.

·

As strong knocking due to pre-ignition may be caused by multiple superimposed factors, even if the engine oil inspection result is NG, perform the following inspections after replacing the engine oil.



Result:
Proceed to
NEXT



NEXT

8.INTERVIEW THE CUSTOMER
8.INTERVIEW THE CUSTOMER
a.

Interview the customer for details about what fuel they have used and smell the fuel to check for the following.

·

If the fuel smells like a mixture of gasoline and diesel fuel, etc.

·

If there is a possibility that diesel fuel may have be added by mistake.

·

If the malfunction started after refueling at an unfamiliar gas station.

·

If fuel additives have been used.


HINT:

Even if any of the above conditions are met, if the engine is not malfunctioning, fill the fuel tank at a different gas station and check if the malfunction recurs.



Result:
Result Proceed to
None of the above conditions are met and the engine is not malfunctioning. A
One or more of the above conditions are met and the engine is malfunctioning. B


HINT:
·

Strong knocking due to pre-ignition may be caused by the type fuel used.

·

The risk of pre-ignition occurring may be increased depending on the ingredients of fuel additives used.

·

Even if no abnormalities are found in this inspection, if a malfunction occurs after the vehicle has been refueled, a problem with the fuel is suspected.




A

9.INSPECT OTHER RELATED COMPONENTS

B

10.REPLACE FUEL
9.INSPECT OTHER RELATED COMPONENTS
a.

Check for accumulated deposits (carbon) and remove them. Deposits (carbon) may act as an ignition source if they become detached, leading to pre-ignition.

HINT:

Strong knocking due to pre-ignition may be caused by detached deposits burning inside the cylinder.



Result:
Proceed to
NEXT



NEXT

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
10.REPLACE FUEL
a.

Replace the fuel.


Result:
Proceed to
NEXT



NEXT

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
11.READ VALUE USING GTS (MASS AIR FLOW SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off.


e.

Enter the following menus: Powertrain / Engine / Data List / Mass Air Flow Sensor.

Powertrain > Engine > Data List
Tester Display
Mass Air Flow Sensor
50003 372 215

f.

According to the display on the GTS, read the Data List when the ignition switch is turned on (IG) and while maintaining an engine speed of 3000 rpm.


Result:
Result Proceed to
Ignition switch ON (engine stopped): 0.57 gm/sec or less
Engine speed 3000 rpm (without load): Less than 5.7 gm/sec
A
Other than above B



A

12.CHECK INTAKE SYSTEM

B

26.PERFORM ACTIVE TEST USING GTS (D-4S (INJECTION VOLUME))
12.CHECK INTAKE SYSTEM
a.

Check for air leaks or blockage in the intake system components. If a connection problem or foreign matter is found, repair the connection or remove the foreign matter.

HINT:
·

If there is foreign matter in the intake system components, remove it before proceeding to the next step.

·

If there is no foreign matter in the intake system components, check for foreign matter in the mass air flow meter. If there is foreign matter in the mass air flow meter, remove it.

·

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

13.CHECK MODEL
13.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Rear air fuel ratio sensor type A
for Rear heated oxygen sensor type B



A

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

26.PERFORM ACTIVE TEST USING GTS (D-4S (INJECTION VOLUME))
14.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


e.

Warm up the air fuel ratio sensors at an engine speed of 2500 rpm for 90 seconds.


f.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2.

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
A/F (O2) Sensor Current B1S1
A/F (O2) Sensor Current B1S2
50004 372 8 230,564

g.

Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.


h.

Monitor the output currents of the air fuel ratio sensors (A/F (O2) Sensor Current B1S1 and A/F (O2) Sensor Current B1S2 displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the air fuel ratio sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output value does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Standard:
GTS Display
(Sensor)
Injection Volume Status Voltage
A/F (O2) Sensor Current B1S1
(Air fuel ratio sensor (sensor 1))
12.5% Rich Below -0.075 mA
-12.5% Lean More than 0.037 mA
A/F (O2) Sensor Current B1S2
(Air fuel ratio sensor (sensor 2))
12.5% Rich Below -0.86 mA
-12.5% Lean More than 0.33 mA



Result:
Status of A/F (O2) Sensor Current B1S1 Status of A/F (O2) Sensor Current B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor (Sensor 1) Condition Proceed to
Lean/Rich Lean/Rich Normal A
Lean Lean Actual air fuel ratio lean B
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor (sensor 1) malfunction C
Rich Lean/Rich Air fuel ratio sensor (sensor 1) malfunction


Lean: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1 is consistently more than 0.037 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2 than 0.33 mA.

Rich: During the Control the Injection Volume for A/F Sensor Active Test, the air fuel ratio sensor (sensor 1) output current (A/F (O2) Sensor Current B1S1 is consistently below -0.075 mA, and the air fuel ratio sensor (sensor 2) output current (A/F (O2) Sensor Current B1S2 is consistently below -0.86 mA.

Lean/Rich: During the Control the Injection Volume for A/F Sensor Active Test, the output current of the air fuel ratio sensor (sensor 1) or air fuel ratio sensor (sensor 2) alternate correctly.

HINT:

Refer to "Data List / Active Test" [A/F (O2) Sensor Current B1S1, A/F (O2) Sensor Current B1S2.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST




A

15.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1) AND AIR FUEL RATIO SENSOR (SENSOR 2)

B

16.REPLACE FUEL INJECTOR ASSEMBLY

C

17.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY (WITH BRUSH))
15.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1) AND AIR FUEL RATIO SENSOR (SENSOR 2)
a.

Replace the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



b.

Replace the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 2).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

36.CONDUCT CONFIRMATION TEST
16.REPLACE FUEL INJECTOR ASSEMBLY
a.

Replace the fuel injector assemblies of all cylinders.

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

36.CONDUCT CONFIRMATION TEST
17.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY (WITH BRUSH))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay (with Brush).

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay (with Brush)
50004 372 24

e.

When performing the Active Test, check for an operating sound from the fuel pump (for low pressure side).

OK:
Activate the Circuit Relay (with Brush) Specified Condition
ON Operating sound heard
OFF Operating sound not heard



Result:
Proceed to
OK
NG



OK

18.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

NG

22.INSPECT FUEL PUMP CONTROL SYSTEM
18.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION

Standard:
Vehicle State Specified Condition
Cranking engine 196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)
5 minutes after stopping engine 98 kPa (1.0 kgf/cm2, 14 psi) or higher


HINT:
·

If there is foreign matter such as iron particles on the fuel pump (for low pressure side), remove it.

·

Make sure that there are no leaks from the fuel lines, signs of fuel leakage or fuel odors.

·

If the air fuel ratio becomes lean only when the engine is running under a high load and at a high engine speed, clogging of the fuel filter is suspected.




Result:
Proceed to
OK
NG



OK

19.READ VALUE USING GTS (HIGH FUEL PRESSURE SENSOR)

NG

21.INSPECT RELATED PARTS
19.READ VALUE USING GTS (HIGH FUEL PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / High Fuel Pressure Sensor.

Powertrain > Engine > Data List
Tester Display
High Fuel Pressure Sensor
50003 372 47

e.

Read the values.

Standard:
3000 rpm:

4 to 8 MPa.


HINT:

The A/C switch and all accessory switches should be off, and the shift lever should be in P position, and the engine should be fully warmed up.



Result:
Proceed to
OK
NG



OK

20.INSPECT OTHER RELATED COMPONENTS

NG

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
20.INSPECT OTHER RELATED COMPONENTS
a.

Inspect other related components.

HINT:

If the malfunctioning part could not be determined by performing the preceding inspections, one of the following malfunctions is suspected.

·

Engine mount deterioration

·

Deposits in the intake manifold or on an intake valve

·

Delay in fuel supply due to adherence of the fuel to the deposits




Result:
Proceed to
NEXT



NEXT

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
21.INSPECT RELATED PARTS
a.

Inspect the following fuel pump (for low pressure side) related parts:

·

Fuel suction plate sub-assembly

·

Fuel main valve assembly

·

Fuel lines and connecting parts

·

Fuel filter



Result:
Proceed to
NEXT



NEXT

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
22.INSPECT FUEL PUMP CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

23.REPAIR OR REPLACE MALFUNCTIONING PARTS
23.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Repair or replace the malfunctioning part.


b.

Perform "Inspection After Repair" after repairing or replacing the malfunctioning part.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

24.CONDUCT CONFIRMATION TEST
24.CONDUCT CONFIRMATION TEST
a.

Check that the engine has returned to normal.


Result:
Proceed to
NEXT



NEXT

25.CLEAR DTC
25.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

END

26.PERFORM ACTIVE TEST USING GTS (D-4S (INJECTION VOLUME))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start the engine and warm it up until the engine coolant temperature 75°C (167°F) or higher with all the accessories switched off.


e.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


f.

Idle the engine.


g.

Enter the following menus: Powertrain / Engine / Active Test / D-4S (Injection Volume) / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.

Powertrain > Engine > Active Test
Active Test Display
D-4S (Injection Volume)
Data List Display
A/F (O2) Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 42012 225,218

h.

According to the display on the GTS, perform the Active Test and check the vehicle conditions when increasing and decreasing the fuel injection volume of port injection and direct injection.

NOTICE:
·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

Read the output voltage immediately after warming up the air fuel ratio sensor and heated oxygen sensor to avoid an inaccurate reading due to a sensor cooling.



HINT:
·

Increase and decrease the fuel injection volume of the port injection and direct injection simultaneously and check the vehicle condition.

·

Change the fuel injection volume between the minimum and maximum range of correction (e.g. -12.5% to 24.8%).



Result:
GTS Display (Sensor) Injection Volume Voltage
A/F (O2) Sensor Voltage B1S1
(Air fuel ratio)
24.8% Below 3.1 V
-12.5% Higher than 3.4 V
O2 Sensor Voltage B1S2
(Heated oxygen)
24.8% Higher than 0.55 V
-12.5% Below 0.4 V



Result:
Result Proceed to
Output voltage values are abnormal A
Malfunction disappears when fuel injection volume is increased B
Malfunction is still present when fuel injection volume is increased, even if output voltage values are normal C



A

27.REPLACE AIR FUEL RATIO SENSOR AND HEATED OXYGEN SENSOR

B

28.REPLACE FUEL INJECTOR ASSEMBLY

C

29.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY (WITH BRUSH))
27.REPLACE AIR FUEL RATIO SENSOR AND HEATED OXYGEN SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

36.CONDUCT CONFIRMATION TEST
28.REPLACE FUEL INJECTOR ASSEMBLY
a.

Replace the fuel injector assemblies of all cylinders.

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

36.CONDUCT CONFIRMATION TEST
29.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY (WITH BRUSH))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay (with Brush).

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay (with Brush)
50004 372 24

e.

When performing the Active Test, check for an operating sound from the fuel pump (for low pressure side).

OK:
Activate the Circuit Relay (with Brush) Specified Condition
ON Operating sound heard
OFF Operating sound not heard



Result:
Proceed to
OK
NG



OK

30.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

NG

34.INSPECT FUEL PUMP CONTROL SYSTEM
30.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Attach a fuel pressure gauge and check the fuel pressure when cranking the engine and after stopping the engine.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION

Standard:
Vehicle State Specified Condition
Cranking engine 196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)
5 minutes after stopping engine 98 kPa (1.0 kgf/cm2, 14 psi) or higher


HINT:
·

If there is foreign matter such as iron particles on the fuel pump (for low pressure side), remove it.

·

Make sure that there are no leaks from the fuel lines, signs of fuel leakage or fuel odors.

·

If the air fuel ratio becomes lean only when the engine is running under a high load and at a high engine speed, clogging of the fuel filter is suspected.




Result:
Proceed to
OK
NG



OK

31.READ VALUE USING GTS (HIGH FUEL PRESSURE SENSOR)

NG

33.INSPECT RELATED PARTS
31.READ VALUE USING GTS (HIGH FUEL PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / High Fuel Pressure Sensor.

Powertrain > Engine > Data List
Tester Display
High Fuel Pressure Sensor
50003 372 47

e.

Read the values.

Standard:
3000 rpm:

4 to 8 MPa.


HINT:

The A/C switch and all accessory switches should be off, and the shift lever should be in P position, and the engine should be fully warmed up.



Result:
Proceed to
OK
NG



OK

32.INSPECT OTHER RELATED COMPONENTS

NG

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
32.INSPECT OTHER RELATED COMPONENTS
a.

Inspect other related components.

HINT:

If the malfunctioning part could not be determined by performing the preceding inspections, one of the following malfunctions is suspected.

·

Engine mount deterioration

·

Deposits in the intake manifold or on an intake valve

·

Delay in fuel supply due to adherence of the fuel to the deposits




Result:
Proceed to
NEXT



NEXT

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
33.INSPECT RELATED PARTS
a.

Inspect the following fuel pump (for low pressure side) related parts:

·

Fuel suction plate sub-assembly

·

Fuel main valve assembly

·

Fuel lines and connecting parts

·

Fuel filter



Result:
Proceed to
NEXT



NEXT

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
34.INSPECT FUEL PUMP CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

35.REPAIR OR REPLACE MALFUNCTIONING PARTS
35.REPAIR OR REPLACE MALFUNCTIONING PARTS
a.

Repair or replace the malfunctioning part.


b.

Perform "Inspection After Repair" after repairing or replacing the malfunctioning part.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

36.CONDUCT CONFIRMATION TEST
36.CONDUCT CONFIRMATION TEST
a.

Check that the engine has returned to normal.


Result:
Proceed to
NEXT



NEXT

37.CLEAR DTC
37.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

END