Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P070513  Transmission Range Sensor "A" Circuit Open  P070562  Transmission Range Sensor "A" Signal Compare Failure  


DESCRIPTION

HINT:

This DTC is applicable to CVT models only.


The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P070513 Transmission Range Sensor "A" Circuit Open All switches are off simultaneously for NSW, P, R, N and D for 1 minute or more (2 trip detection logic).
·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch

·

ECM


Comes on DTC stored SAE Code:
P0705
P070562 Transmission Range Sensor "A" Signal Compare Failure Either of the following condition A or B is met (2 trip detection logic):
A. One of the following conditions (a), (b) or (c) is met for 2 seconds or more:
(a) Any 2 or more of the following signals are ON simultaneously:
·

P input signal

·

R input signal

·

D input signal


(b) Any 2 or more of the following signals are ON simultaneously:
·

N input signal

·

R input signal

·

D input signal


(c) Any 2 or more of the following signals are ON simultaneously:
·

NSW input signal

·

R input signal

·

D input signal


B. Any of the following conditions is met for 2 seconds or more with the shift lever in M:
·

NSW input signal is ON

·

P input signal is ON

·

N input signal is ON

·

R input signal is ON


·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch

·

Open or short in transmission control switch circuit

·

Shift lock control unit assembly (Transmission control switch)

·

ECM


Comes on DTC stored SAE Code:
P0705

MONITOR DESCRIPTION

These DTCs indicate a problem with the park/neutral position switch and the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position and sends a signal to the ECM.

For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D, or M). The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will then illuminate the MIL and store a DTC.

MONITOR STRATEGY

Required Sensors/Components Park/Neutral position switch
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Move the shift lever to R and wait 2 seconds or more.

9.

Move the shift lever to N and wait 2 seconds or more.

10.

Move the shift lever to D and wait 2 seconds or more.

11.

Move the shift lever to M and wait 2 seconds or more.

12.

Move the shift lever to P and wait 2 seconds or more.

13.

Wait 1 minute or more.

14.

Enter the following menus: Powertrain / Engine / Trouble Codes.

15.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



16.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

17.

Input the DTC: P070513 or P070562.

18.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A396027E09
5.729,5.885 6.188,6.083 0.458,0.198 10 false ECM 5.229,5.167 5.688,5.365 0.458,0.198 10 false A38 5.219,3.594 5.677,3.792 0.458,0.198 10 false C62 5.229,2.979 5.688,3.177 0.458,0.198 10 false C62 5.229,2.396 5.688,2.594 0.458,0.198 10 false C62 5.229,1.792 5.688,1.99 0.458,0.198 10 false C62 5.219,1.177 5.677,1.375 0.458,0.198 10 false A38 5.271,0.99 5.583,1.188 0.313,0.198 10 false 57 5.271,1.573 5.583,1.771 0.313,0.198 10 false 34 5.208,2.052 5.99,2.26 0.781,0.208 10 false 66*1 5.271,2.781 5.583,2.979 0.313,0.198 10 false 35 5.208,3.24 5.583,3.448 0.375,0.208 10 false 65*1 5.271,4.969 5.583,5.167 0.313,0.198 10 false 59 5.594,5.156 5.781,5.375 0.188,0.219 10 false S 5.604,3.583 5.76,3.781 0.156,0.198 10 false P 5.583,2.969 5.74,3.167 0.156,0.198 10 false R 5.594,2.375 5.75,2.573 0.156,0.198 10 false N 5.583,1.771 5.74,1.969 0.156,0.198 10 false D 5.594,1.167 6.052,1.365 0.458,0.198 10 false NSW 3.76,5.094 3.948,5.313 0.188,0.219 10 false 5 2.594,5.083 2.75,5.281 0.156,0.198 10 false 4 2.771,5.104 3.083,5.302 0.313,0.198 10 false IG 3.583,5.094 3.74,5.292 0.156,0.198 10 false S 3.771,3.49 3.927,3.688 0.156,0.198 10 false 3 3.75,2.896 3.906,3.094 0.156,0.198 10 false 2 3.75,2.292 3.906,2.49 0.156,0.198 10 false 8 3.76,1.698 3.917,1.896 0.156,0.198 10 false 7 3.76,1.104 3.917,1.302 0.156,0.198 10 false 4 3.573,1.104 3.729,1.302 0.156,0.198 10 false B 3.521,1.698 3.833,1.896 0.313,0.198 10 false DL 3.521,2.292 3.833,2.49 0.313,0.198 10 false NL 3.521,2.896 3.833,3.094 0.313,0.198 10 false RL 3.531,3.5 3.844,3.698 0.313,0.198 10 false PL 2.75,2.615 3.063,2.813 0.313,0.198 10 false RB 2.771,1.094 2.927,1.292 0.156,0.198 10 false L 2.583,1.094 2.74,1.292 0.156,0.198 10 false 9 2.594,2.604 2.75,2.802 0.156,0.198 10 false 1 2.615,5.646 3.073,5.844 0.458,0.198 10 false F17 2.583,4.063 3.042,4.26 0.458,0.198 10 false C36 2.573,4.219 4.448,4.781 1.875,0.563 10 false Park/Neutral Position Switch 2.615,5.844 5.031,6.563 2.417,0.719 10 false Transmission Control Switch Assembly (Shift Lock Control unit Assembly) 0.26,5.167 1.833,5.604 1.573,0.438 10 false from ECU-IG NO. 1 Fuse 0.552,2.688 1.844,3.104 1.292,0.417 10 false form BKUP LP Fuse 1.052,1.156 1.875,1.49 0.823,0.333 10 false to ST Relay 0.229,6.042 2.5,6.438 2.271,0.396 10 false *1: w/ Differential Pressure Sensor 0.229,6.438 2.594,6.844 2.365,0.406 10 false *2: w/o Differential Pressure Sensor 5.208,2.188 5.823,2.385 0.615,0.198 10 false 65*2 5.208,3.385 5.625,3.573 0.417,0.188 10 false 64*2 0.104,0.063 2.208,0.51 2.104,0.448 12 false for TMMT Made:

A396027E10
5.729,5.885 6.188,6.083 0.458,0.198 10 false ECM 5.229,5.167 5.688,5.365 0.458,0.198 10 false A38 5.219,3.594 5.677,3.792 0.458,0.198 10 false C74 5.229,2.979 5.688,3.177 0.458,0.198 10 false C74 5.229,2.396 5.688,2.594 0.458,0.198 10 false C74 5.229,1.792 5.688,1.99 0.458,0.198 10 false C74 5.219,1.177 5.677,1.375 0.458,0.198 10 false A38 5.271,0.99 5.583,1.188 0.313,0.198 10 false 57 5.271,1.573 5.583,1.771 0.313,0.198 10 false 34 5.271,2.167 6.052,2.375 0.781,0.208 10 false 66 5.271,2.781 5.583,2.979 0.313,0.198 10 false 35 5.26,3.365 5.635,3.573 0.375,0.208 10 false 65 5.271,4.969 5.583,5.167 0.313,0.198 10 false 59 5.594,5.156 5.781,5.375 0.188,0.219 10 false S 5.604,3.583 5.76,3.781 0.156,0.198 10 false P 5.583,2.969 5.74,3.167 0.156,0.198 10 false R 5.594,2.375 5.75,2.573 0.156,0.198 10 false N 5.583,1.771 5.74,1.969 0.156,0.198 10 false D 5.594,1.167 6.052,1.365 0.458,0.198 10 false NSW 3.76,5.094 3.948,5.313 0.188,0.219 10 false 5 2.594,5.083 2.75,5.281 0.156,0.198 10 false 4 2.771,5.104 3.083,5.302 0.313,0.198 10 false IG 3.583,5.094 3.74,5.292 0.156,0.198 10 false S 3.771,3.49 3.927,3.688 0.156,0.198 10 false 3 3.75,2.896 3.906,3.094 0.156,0.198 10 false 2 3.75,2.292 3.906,2.49 0.156,0.198 10 false 8 3.76,1.698 3.917,1.896 0.156,0.198 10 false 7 3.76,1.104 3.917,1.302 0.156,0.198 10 false 4 3.573,1.104 3.729,1.302 0.156,0.198 10 false B 3.521,1.698 3.833,1.896 0.313,0.198 10 false DL 3.521,2.292 3.833,2.49 0.313,0.198 10 false NL 3.521,2.896 3.833,3.094 0.313,0.198 10 false RL 3.531,3.5 3.844,3.698 0.313,0.198 10 false PL 2.75,2.615 3.063,2.813 0.313,0.198 10 false RB 2.771,1.094 2.927,1.292 0.156,0.198 10 false L 2.583,1.094 2.74,1.292 0.156,0.198 10 false 9 2.594,2.604 2.75,2.802 0.156,0.198 10 false 1 2.615,5.646 3.073,5.844 0.458,0.198 10 false F17 2.583,4.063 3.042,4.26 0.458,0.198 10 false C36 2.573,4.219 4.448,4.781 1.875,0.563 10 false Park/Neutral Position Switch 2.615,5.844 5.031,6.563 2.417,0.719 10 false Transmission Control Switch Assembly (Shift Lock Control unit Assembly) 0.26,5.167 1.833,5.604 1.573,0.438 10 false from ECU-IG NO. 1 Fuse 0.552,2.688 1.844,3.104 1.292,0.417 10 false form BKUP LP Fuse 1.052,1.156 1.875,1.49 0.823,0.333 10 false to ST Relay 0.177,0.146 1.698,0.49 1.521,0.344 12 false for TMC Made:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may by discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Shift SW Status (P Range), Shift SW Status (R Range), Shift SW Status (N Range), Shift SW Status (S Range) and Shift SW Status (D Range).

Powertrain > Engine > Data List
Tester Display
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (S Range)
Shift SW Status (D Range)
50003 372 15,14,13,27,28

e.

Read the Data List displayed on the GTS.

GTS Display Measurement Item/Range Normal Condition Diagnostic Note
Shift SW Status (R Range) Park/Neutral position switch status:
ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (P Range) Park/Neutral position switch status:
ON or OFF
·

ON: Shift lever in P

·

OFF: Shift lever not in P


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (N Range) Park/Neutral position switch status:
ON or OFF
·

ON: Shift lever in N

·

OFF: Shift lever not in N


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect
Shift SW Status (S Range) Transmission control switch status:
ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-
Shift SW Status (D Range) Park/Neutral position switch status:
ON or OFF
·

ON: Shift lever in D or M

·

OFF: Shift lever not in D or M


When shift lever position displayed on GTS differs from actual position, adjustment of park/neutral position switch or shift cable may be incorrect



PROCEDURE

1.READ VALUE USING GTS (NEUTRAL POSITION SW AND SHIFT SW STATUS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Neutral Position SW and Shift SW Status (P, R, N and D Range).

Powertrain > Engine > Data List
Tester Display
Neutral Position SW
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (D Range)
50003 372 20,15,14,13,28

e.

According to the display on the GTS, read the Data List.

OK:
GTS Display Shift Lever Position Specified Condition
Neutral Position SW P or N ON
Except P or N OFF
Shift SW Status (P Range) P ON
Except P OFF
Shift SW Status (R Range) R ON
Except R OFF
Shift SW Status (N Range) N ON
Except N OFF
Shift SW Status (D Range) D or M ON
Except D or M OFF



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))

NG

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH)
2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Shift SW Status (S Range).

Powertrain > Engine > Data List
Tester Display
Shift SW Status (S Range)
50003 372 27

e.

Read the Data List displayed on the GTS.

OK:
GTS Display Shift Lever Position Specified Condition
Shift SW Status (S Range) M, "+" or "-" ON
Except M, "+" or "-" OFF



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY
3.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY
a.

Inspect the Shift lock control unit assembly (Transmission control switch).

for 2WD: Click hereDrivetrain>K313 (MULTIDRIVE / CVT)>SHIFT LEVER>INSPECTION

for AWD: Click hereDrivetrain>K313F (MULTIDRIVE / CVT)>SHIFT LEVER>INSPECTION


Result:
Result Proceed to
OK A
NG (for 2WD) B
NG (for AWD) C



A

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH))

B

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

C

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH))
A352211C11
0.396,1.104 0.76,1.344 0.365,0.24 2.104,1.948 1.833,1.552 true 0.313,0.219 0.625,0.417 0.313,0.198 10 false *a 0.458,1.125 0.771,1.323 0.313,0.198 10 false F17 2.188,1.917 2.5,2.115 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Shift lock control unit assembly (Transmission control switch))


a.

Disconnect the shift lock control unit assembly (transmission control switch) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F17-4 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY(TRANSMISSION CONTROL SWITCH) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY(TRANSMISSION CONTROL SWITCH) - ECM)
a.

Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-5 (S) - A38-59 (S) Always Below 1 Ω
F17-5 (S) or A38-59 (S) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH)
A194118C28
0.26,2.26 0.698,2.521 0.438,0.26 1.573,2.406 0.885,1.635 true 0.229,0.135 0.438,0.302 0.208,0.167 10 false *a 0.344,2.292 1.292,2.823 0.948,0.531 10 false C36 0.76,1.448 0.979,1.604 0.219,0.156 10 false RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch)


a.

Disconnect the park/neutral position switch connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C36-1 (RB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

7.INSPECT PARK/NEUTRAL POSITION SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH POWER SOURCE CIRCUIT)

7.INSPECT PARK/NEUTRAL POSITION SWITCH

Result:
Result Proceed to
OK A
NG (for 2WD) B
NG (for AWD) C



A

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)

B

REPLACE PARK/NEUTRAL POSITION SWITCH

C

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the C36 park/neutral position switch connector.


b.

Disconnect the A38, C62*1 or C74*2 ECM connector.

*1: for TMMT Made

*2: for TMC Made



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for TMMT Made
Tester Connection Condition Specified Condition
C36-4 (B) - A38-57 (NSW) Always Below 1 Ω
C36-7 (DL) - C62-34 (D) Always Below 1 Ω
C36-8 (NL) - C62-66 (N)*1 Always Below 1 Ω
C36-8 (NL) - C62-65 (N)*2 Always Below 1 Ω
C36-2 (RL) - C62-35 (R) Always Below 1 Ω
C36-3 (PL) - C62-65 (P)*1 Always Below 1 Ω
C36-3 (PL) - C62-64 (P)*2 Always Below 1 Ω
C36-4 (B) or A38-57 (NSW) - Body ground and other terminals Always 10 kΩ or higher
C36-7 (DL) or C62-34 (D) - Body ground and other terminals Always 10 kΩ or higher
C36-8 (NL), C62-66 (N)*1 or C62-65 (N)*2 - Body ground and other terminals Always 10 kΩ or higher
C36-2 (RL) or C62-35 (R) - Body ground and other terminals Always 10 kΩ or higher
C36-3 (PL), C62-65 (P)*1 or C62-64 (P)*2 - Body ground and other terminals Always 10 kΩ or higher

for TMC Made
Tester Connection Condition Specified Condition
C36-4 (B) - A38-57 (NSW) Always Below 1 Ω
C36-7 (DL) - C74-34 (D) Always Below 1 Ω
C36-8 (NL) - C74-66 (N) Always Below 1 Ω
C36-2 (RL) - C74-35 (R) Always Below 1 Ω
C36-3 (PL) - C74-65 (P) Always Below 1 Ω
C36-4 (B) or A38-57 (NSW) - Body ground and other terminals Always 10 kΩ or higher
C36-7 (DL) or C74-34 (D) - Body ground and other terminals Always 10 kΩ or higher
C36-8 (NL) or C74-66 (N) - Body ground and other terminals Always 10 kΩ or higher
C36-2 (RL) or C74-35 (R) - Body ground and other terminals Always 10 kΩ or higher
C36-3 (PL) or C74-65 (P) - Body ground and other terminals Always 10 kΩ or higher


*1: w/ Differential Pressure Sensor

*2: w/o Differential Pressure Sensor



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR