2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Tachometer Malfunction

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The meter CPU receives engine revolution signals from the ECM via the CAN communication lines (CAN No. 1 Bus). The meter CPU displays engine revolution data that is calculated based on the data received from the ECM.

WIRING DIAGRAM

E128084E03

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication DTC is output (Click here for LHD without Smart Entry and Start System, Click here for LHD with Smart Entry and Start System, Click here for RHD without Smart Entry and Start System, Click here for RHD with Smart Entry and Start System).

    Result:
    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B (Click here for LHD without Smart Entry and Start System, Click here for LHD with Smart Entry and Start System, Click here for RHD without Smart Entry and Start System, Click here for RHD with Smart Entry and Start System)



B
GO TO CAN COMMUNICATION SYSTEM
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the values in the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Tacho Meter Operation
    Tachometer
    0, 1,000, 2,000, 3,000, 4,000, 5,000, 6,000, 7,000 (rpm)
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


3. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the operation by referring to the values in the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Rpm
    Engine speed/Min.: 0 rpm, Max.: 12,800 rpm
    Almost same as actual engine speed (When engine is running)
    If data received from the ECM exceeds the range that can be displayed on the meter, the meter continues to display the maximum value of the range.

    OK:
    Engine speed displayed on the tester is almost the same as the actual engine speed.



NG
Go to step 4
OK

REPLACE COMBINATION METER ASSEMBLY

4. READ VALUE USING INTELLIGENT TESTER (ENGINE SPEED SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Power train / Engine / Data List.

  1. Check the values by referring to the table below.

    Engine: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Engine Speed
    Engine speed/Min.: 0 rpm, Max.: 16,383.75 rpm
    Almost same as actual engine speed (When engine is running)
    -

    OK:
    Engine speed displayed on the tester is almost the same as the actual engine speed.



NG
GO TO SFI SYSTEM
OK


5. REPLACE ECM
  1. Replace the ECM with a new or a normal one.

    OK:
    The operation of the tachometer returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK

END


← Tachometer Malfunction (Oct 2006 – May 2009)Fuel Receiver Gauge Malfunction (Jun 2006 – Sep 2006) →