Engine does not Start
Circuit diagnosis · Vehicles built Oct 2006 – May 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
| ENGINE START SYSTEM FUNCTION |
If the engine switch is pressed with the shift lever in the P or N position and the brake pedal depressed, the main body ECU determines that it is an engine start request.
The certification ECU and other ECUs perform key verification via the LIN communication line.
The main body ECU activates the ACC relay.
The main body ECU activates the IG1 and IG2 relays.
The certification ECU outputs a steering UNLOCK signal. The signal is sent to the main body ECU via the steering lock ECU.
The main body ECU sends an engine start request signal to the ECM.
The ECM sends an ACC cut request signal to the main body ECU.
The ECM and main body ECU activate the ST relay.
The main body ECU deactivates the ACC relay until the ECU detects an engine start.
When engine revolution speed reaches 1200 rpm, the ECM determines that the engine has been started.
The ECM stop sending on ACC cut request signal to the main body ECU.
The main body ECU reactivates the ACC relay and turns off the engine switch indicator light, when engine revolution speed reaches 800 rpm.Symbols of main body ECU
Signals
STP
Stop light switch ON signal
Input
SSW1/SSW2
Engine switch ON signal
Input
ACCD
ACC relay operation signal
Output
SLP
Shift lock actuator position signal
Input
IG1D
IG1 relay operation signal
Output
P
Shift lock signal
Input
IG2D
IG2 relay operation signal
Output
STR2
ST relay operation signal (Sub)
Output
STR
Park/neutral position switch signal
Input
TACH
Engine start detection signal
Input
STSW
Starter activation request signal
Output
ACCR
ACC cut request signal
Input
Symbols of ECM
Signals
ACCR
ACC cut request signal
Output
TACH
Engine revolution speed signal
Output
STSW
Starter activation request signal
Input
NSW
Park/neutral position switch signal
Input
STAR
ST relay operation signal (Main)
Output
STA
Starter activation signal
Input




WIRING DIAGRAM
See CRANKING HOLDING FUNCTION CIRCUIT (Click here).INSPECTION PROCEDURE
| EMERGENCY ENGINE START CONTROL |
If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
To activate the starter:Turn the engine switch from off to on (ACC).
Press and hold the engine switch for 15 seconds.
- HINT:
- After the main body ECU, certification ECU, steering lock ECU, ID code box and/or ECM are/is replaced, perform the registration procedures for the engine immobiliser system.
| 1. CHECK ENTRY FUNCTION DETECTION AREA |
Inspect entry detection area.

When the electrical key is in either of the 2 inspection points in the illustration, the shift lever is in the P position and the brake pedal is depressed, check that the engine switch indicator illuminates in green.
- OK:
- Engine switch illuminates in green.
- HINT:
- If the engine switch does not illuminate, perform troubleshooting according to the PROBLEM SYMPTOMS TABLE of the smart entry and start system (starting) (engine switch indicator light does not come on) (Click here) and the smart entry and start system (entry door lock) (matching for the inside of the cabin cannot be performed) (Click here).
|
|
||||
| OK | |
| 2. CHECK IF ENGINE STARTS (INITIALIZE STEERING LOCK) |
Turn the engine switch off.
Make sure that the shift lever is in the P position.
Open and close the driver's door.
When the shift lever is in the P position and the brake pedal is depressed, check if the engine can be started.
- OK:
- Steering lock/unlock function operates normally and engine can be started.
- HINT:
- After the battery is discharged and then recharged, the engine may not start unless the steering lock is initialized using the above procedure (Click here).
|
|
||||
| OK | ||
| ||
| 3. CHECK FOR DTC |
Delete the DTCs (Click here).
Check for DTCs again.
- OK:
- No DTC is output.
- HINT:
- If smart entry and start system (starting function) DTCs are output (Click here).
- If wireless door lock control system DTCs are output (Click here).
- If electrical steering lock DTCs are output (Click here).
- If engine immobiliser system DTCs are output (Click here).
- If engine control system DTCs output (2GR-FE) (Click here).
- If smart entry and start system (starting function) DTCs are output (Click here).
|
|
||||
| OK | |
| 4. CHECK ENGINE SWITCH CONDITION |
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:
- OK:
- off → on (ACC) → on (IG) → off
- HINT:
- If power mode does not change to ON (IG and ACC) (Click here).
- If power mode does not change to ON (IG) (Click here).
- If power mode does not change to ON (ACC) (Click here).
- If power mode does not change to ON (IG and ACC) (Click here).
|
|
||||
| OK | |
| 5. CHECK CRANKING FUNCTION |
Check the engine cranking function.
When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch crank the engine.
- Result:
Result
Proceed to
Engine doesn't crank.
A
Engine cranks.
B
|
|
||||
| A | |
| 6. READ VALUE USING INTELLIGENT TESTER (P SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Read the DATA LIST according to the displays on the tester screen.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Shift P Sig
Shift P signal / ON or OFF
ON: Shift position is P
OFF: Shift position is not P
-
- OK:
- ON (P signal is ON) and OFF (P signal is OFF) appear on the screen.
- HINT:
- If the result is not as specified, perform troubleshooting for DTC B2281 ("P" signal malfunction) first (Click here).
|
|
||||
| OK | |
| 7. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Check the DATA LIST for proper functioning of the stop light switch.
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light SW
Stop light Switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
- OK:
- ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen.
- HINT:
- If the result is not as specified, perform troubleshooting for DTC B2284 (Brake signal malfunction) first (Click here).
|
|
||||
| OK | |
| 8. READ VALUE USING INTELLIGENT TESTER (STEERING LOCK) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Body: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Str Unlock SW
Steering lock condition / ON or OFF
ON: Steering is unlocked (Engine switch on (ACC))
OFF: Steering is locked (Engine switch off)
-
- OK:
- ON (steering is unlocked) and OFF (steering is locked) appear on the screen.
- HINT:
- If the result is not as specified, perform troubleshooting for DTCs B2285 (Steering lock position signal circuit malfunction) and B2288 (Steering lock signal circuit malfunction) first (Click here).
|
|
||||
| OK | |
| 9. CHECK STEERING LOCK |
Check if the steering lock is released when turning the engine switch on (ACC).
- OK:
- The steering lock is released.
|
|
||||
| OK | |
| 10. INSPECT MAIN BODY ECU (STSW VOLTAGE) |
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
E9-4 (STSW) - Body ground
Brake pedal depressed, engine switch held on (ST)
Output voltage at terminal AM1 or AM2 is -2 V or more.
- HINT:
- If the result is not as specified, perform troubleshooting for DTC B2275 (STSW monitor malfunction) first (Click here).
|
|
||||
| OK | |
| 11. INSPECT ECM (ACCR VOLTAGE) |
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
E6-3 (ACCR) - Body ground
Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG)
0.1 to 0.8 V*1 → Output voltage at terminal AM1 or AM2 is -2 V or more.
- HINT:
- If the result is not as specified, perform troubleshooting for DTC B2276 (ACCR signal circuit malfunction) first (Click here).
|
|
||||
| OK | |
| 12. INSPECT MAIN BODY ECU (STR VOLTAGE) |
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
E7-8 (STR) - Body ground
Shift lever P or N position → except P or N position
Below 2 V → Pulse generation
Proceed to the next step based on the inspection result.
- Result:
Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 13. INSPECT RELAY (ST CUT) |
Measure the resistance of the ST CUT relay.

- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 14. INSPECT PARK/NEUTRAL POSITION SWITCH |
Disconnect the park/neutral position (PNP) switch connector.

Measure the resistance according the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
4 - 9
P
Below 1 Ω
4 - 9
N
Below 1 Ω
4 - 9
Except P and N
10 kΩ or higher
|
|
||||
| OK | |
| 15. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM, MAIN BODY ECU) |
Disconnect the C58*1 or C55*2 ECM connector.


Disconnect the E7 main body ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
C55-62 (NSW) - C1-4*1
C58-62 (NSW) - C1-4*2
Always
Below 1 Ω
C55-62 (NSW) - E7-8 (STR)*1
C58-62 (NSW) - E7-8 (STR)*2
Always
Below 1 Ω
C55-62 (NSW) - Body ground*1
C58-62 (NSW) - Body ground*2
Always
10 kΩ or higher
- HINT:
- *1: LHD
- *2: RHD
|
|
||||
| OK | |
| 16. INSPECT INSTRUMENT PANEL JUNCTION BLOCK (STR2 VOLTAGE) |
Disconnect the C55 ECM connector (LHD).

Disconnect the C58 ECM connector (RHD).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Condition
Specified Condition
E9-6 (STR2) - Body ground
Brake pedal depressed, shift lever P or N position, engine switch on (ST)
Output voltage at terminal AM1 or AM2 is -3.5 V or more.*1
|
|
||||
| OK | |
| 17. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ECM - ENGINE ROOM RELAY BLOCK) |
Remove the ST CUT relay from the engine room R/B.


Disconnect the E9 ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
C55-63 (STAR) - E9-6 (STR2)*1
C58-63 (STAR) - E9-6 (STR2)*2
Always
Below 1 Ω
C55-63 (STAR) - ST CUT relay terminal - 3*1
C58-63 (STAR) - ST CUT relay terminal - 3*2
Always
Below 1 Ω
C55-63 (STAR) - Body ground*1
C58-63 (STAR) - Body ground*2
Always
10 kΩ or higher
- HINT:
- *1: LHD
- *2: RHD
|
|
||||
| OK | |
| 18. INSPECT RELAY (ST) |
Remove the starter relay from the engine room R/B.

Measure the resistance of the starter relay.
- Standard resistance:
Tester Connection
Condition
Specified Condition
3 - 5
When battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
3 - 5
When battery voltage is applied to terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 19. CHECK HARNESS AND CONNECTOR (ECM - ST RELAY, PARK/NEUTRAL POSITION SWITCH) |
Disconnect the A55 ECM connector (LHD).


Disconnect the A24 ECM connector (RHD).
Measure the resistance according the value(s) in the table below.
- Standard resistance:
Tester Connection
Condition
Specified Condition
A55-48 (STA) - Engine Room R/B ST relay terminal - 1*1
A24-48 (STA) - Engine Room R/B ST relay terminal - 1*2
Always
Below 1 Ω
A55-48 (STA) - C1-9*1
A24-48 (STA) - C1-9*2
Always
Below 1 Ω
A55-48 (STA) - Body ground*1
A24-48 (STA) - Body ground*2
Always
10 kΩ or higher
- HINT:
- *1: LHD
- *2: RHD
|
|
||||
| OK | |
| 20. INSPECT ENGINE ROOM RELAY BLOCK (ST RELAY VOLTAGE) |
Measure the voltage according to the value(s) in the table below.

- Standard voltage:
Tester Connection
Condition
Specified Condition
ST relay terminal - 5 - Body ground
Always
11 to 14 V
ST relay terminal - 2 - Body ground
Always
Below 1 V
|
|
||||
| OK | |
| 21. INSPECT STARTER ASSEMBLY |
- HINT:
- (Click here).
|
|
||||
| OK | ||
| ||
| 22. READ VALUE USING INTELLIGENT TESTER (L CODE) |
Reconnect the connectors.
Connect the intelligent tester to the DLC3.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
Entry & Start (Certification ECU): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
L Code Chk
L code check / ON or NG
OK: Normal
NG: Malfunction
Electrical key in the cabin
- OK:
- OK is displayed on the screen.
- HINT:
- If the result is not as specified, refer to PROBLEM SYMPTOMS TABLE of the electrical steering lock (steering wheel cannot be unlocked) (Click here).
- If the result is not as specified, there may be a malfunction with the steering lock ECU or the ID code box.
|
|
||||
| OK | |
| 23. READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST) |
Connect the intelligent tester to the DLC3.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
Entry & Start (Certification ECU): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Start Rqst
Start request signal response / OK or NG
OK: Received
NG: Not received
-
- OK:
- OK (received) and NG (not received) appear on the screen.
|
|
||||
| OK | |
| 24. READ VALUE USING INTELLIGENT TESTER (S CODE) |
Connect the intelligent tester to the DLC3.
- HINT:
- When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.
Turn the engine switch on (IG).
Entry & Start (Certification ECU): Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
S Code Chk
S code check / OK or NG
OK: Normal
NG: Malfunction
-
- OK:
- OK is displayed on the screen.
- HINT:
- If the result is not as specified, there may be a malfunction with the certification ECU or the ID code box.
|
|
||||
| OK | |
| 25. INSPECT ID CODE BOX |
Check the input signal waveform.

Connect an oscilloscope to terminal E50-6 (EFIO) and body ground.
Turn the engine switch on (IG).
Check the signal waveform according to the condition(s) in the table below.
Item
Condition
Tool setting
10 V/DIV., 100 ms./DIV.
Vehicle condition
Engine switch on (IG)
|
|
||||
| OK | ||
| ||
| 26. REPLACE CERTIFICATION ECU |
Replace the certification ECU.
Perform the registration procedures for the engine immobiliser system.
Check if the engine can be started.
- OK:
- Engine can be started.
|
|
||||
| NG | ||
| ||
