2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Speedometer Malfunction

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

The meter CPU receives vehicle speed signals from the skid control ECU via the CAN communication lines (CAN No. 1 Bus). The vehicle speed sensor detects the voltage that varies according to the vehicle speed. The skid control ECU supplies power to the vehicle speed sensor. The skid control ECU detects vehicle speed signals based on the pulses of the voltage.

HINT:
Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear.
The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).


WIRING DIAGRAM

E128084E02

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication DTC is output (Click here for LHD without Smart Entry and Start System, Click here for LHD with Smart Entry and Start System, Click here for RHD without Smart Entry and Start System, Click here for RHD with Smart Entry and Start System).

    Result:
    Result
    Proceed to
    CAN communication DTC is not output.
    A
    CAN communication DTC is output.
    B (Click here for LHD without Smart Entry and Start System, Click here for LHD with Smart Entry and Start System, Click here for RHD without Smart Entry and Start System, Click here for RHD with Smart Entry and Start System)



B
GO TO CAN COMMUNICATION SYSTEM
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the values in the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Normal Condition
    Speed Meter Operation
    Speedometer
    0, 40, (24), 80 (48), 120 (72), 160 (96), 200 (120) km/h (mph)
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


3. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the values by referring to the values in the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Almost same as actual speed (When driving)
    If data received from the skid control ECU exceeds the range that can be displayed on the meter, the meter continues to display the maximum value of the range.

    OK:
    Vehicle speed displayed on the tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 4
OK

REPLACE COMBINATION METER ASSEMBLY

4. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / ABS/VSC/TRC / Data List.

  1. Check the values by referring to the table below.

    ABS/VSC/TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Almost same as actual speed (When driving)
    -
    FL Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Almost same as actual speed (When driving)
    -
    RR Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Almost same as actual speed (When driving)
    -
    RL Wheel Speed
    Vehicle speed/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
    Almost same as actual speed (When driving)
    -

    OK:
    Vehicle speed displayed on the tester is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
GO TO BRAKE CONTROL SYSTEM
OK


5. REPLACE SKID CONTROL ECU
  1. Replace the skid control ECU with a new or a normal one.

    OK:
    The operation of the speedometer returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK

END


← Speedometer Malfunction (Oct 2006 – May 2009)Tachometer Malfunction (Jun 2006 – Sep 2006) →