C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction
Diagnostic trouble codes · Vehicles built Jun 2006 – Sep 2006
Also covers:
- C0215/34 Left Rear Wheel Speed Sensor Signal Malfunction
- C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)
- C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)
- C1332/38 Right Rear Speed Sensor Circuit
- C1333/39 Left Rear Speed Sensor Circuit
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
Refer to DTCs C0200/31, C0205/32, C1330/35, and C1331/36 (Click here).DTCs from C1273/73 to C1278/78 can be deleted when the speed sensor sends a vehicle speed signal or the test mode ends. DTCs from C1273/73 to C1278/78 are output only in the test mode.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| C0210/33 C0215/34 |
When either of the following is detected:
|
|
| C1332/38 C1333/39 |
Abnormality in the resistance value of each speed sensor is detected. |
|
| C1273/73 C1274/74 |
Detected only during test mode. |
|
| C1277/77 C1278/78 |
Detected only during test mode. |
|
- HINT:
- DTC No. C0210/33 and C1332/38 are for the rear speed sensor RH.
- DTC No. C0215/34 and C1333/39 are for the rear speed sensor LH.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Check the condition of each related circuit connector before troubleshooting (Click here).
| 1. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select "Data List" and read the value displayed on the intelligent tester (Click here).
Data List: ABS Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Speed indicated on Speedometer
RL Wheel Speed
Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Speed indicated on Speedometer
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.
|
|
||||
| OK | |
| 2. PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Check if test mode (signal check) DTCs are detected (Click here).
- Result:
Condition
Proceed to
Test mode (signal check) DTC is not output
A
Test mode (signal check) DTC is output
B
|
|
||||
| A | |
| 3. INSPECT SPEED SENSOR SIGNAL WAVEFORM |
Lift up the vehicle.

Perform the inspection using an oscilloscope.
Disconnect the skid control ECU connector.
Connect the oscilloscope to terminals of the skid control ECU.
Check that a waveform is output when the tires are rotated.
- OK:
- The same waveform is output from rear wheels and there is no noise or interference in the waveform.
- HINT:
- As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
- When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.
- As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
Connect the connector.
|
|
||||
| OK | |
| 4. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.
Check if the same DTCs are recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output
A
DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
B
DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the DTC CHART)
C
|
|
||||
|
|
||||
| A | |
| 5. INSPECT SPEED SENSOR INSTALLATION |
Check the rear speed sensor installation.

- OK:
- There is no clearance between the sensor and rear axle carrier.
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 6. INSPECT REAR SPEED SENSOR |
Disconnect the rear speed sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- LH:
Tester Connection
Specified Condition
g1-2 (RL+) - g1-1 (RL-)
Below 2.2 kΩ
g1-2 (RL+) - Body ground
10 kΩ or higher
g1-1 (RL-) - Body ground
10 kΩ or higher
- RH:
Tester Connection
Specified Condition
f1-2 (RR+) - f1-1 (RR-)
Below 2.2 kΩ
f1-2 (RR+) - Body ground
10 kΩ or higher
f1-1 (RR-) - Body ground
10 kΩ or higher
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO SKID CONTROL ECU) |
Check harness and connector.

Disconnect the skid control ECU connector and the rear speed sensor connector.
Disconnect the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- LH:
Tester Connection
Specified Condition
A25-7 (RL+) - g1-2 (RL+)
Below 1 Ω
A25-17 (RL-) - g1-1 (RL-)
Below 1 Ω
g1-2 (RL+) - Body ground
10 kΩ or higher
g1-1 (RL-) - Body ground
10 kΩ or higher
- RH:
Tester Connection
Specified Condition
A25-19 (RR+) - f1-2 (RR+)
Below 1 Ω
A25-8 (RR-) - f1-1 (RR-)
Below 1 Ω
f1-2 (RR+) - Body ground
10 kΩ or higher
f1-1 (RR-) - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO REAR SPEED SENSOR) |
Check harness and connector (skid control sensor wire).

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- LH:
Tester Connection
Specified Condition
g1-1 - A-1
Below 1 Ω
g1-1 - A-2
10 kΩ or higher
g1-1 - Body ground
10 kΩ or higher
g1-2 - A-2
Below 1 Ω
g1-2 - A-1
10 kΩ or higher
g1-2 - Body ground
10 kΩ or higher
- RH:
Tester Connection
Specified Condition
f1-1 - A-1
Below 1 Ω
f1-1 - A-2
10 kΩ or higher
f1-1 - Body ground
10 kΩ or higher
f1-2 - A-2
Below 1 Ω
f1-2 - A-1
10 kΩ or higher
f1-2 - Body ground
10 kΩ or higher
|
|
||||
| OK | |
| 9. INSPECT SPEED SENSOR SIGNAL WAVEFORM |
Lift up the vehicle.

Perform the inspection using the oscilloscope.
Disconnect the skid control ECU connector.
Connect the oscilloscope to terminals of the skid control ECU.
Check that a waveform is output when the tires are rotated.
- OK:
- The same waveforms is output from rear wheels and there is no noise or interference in the waveform.
- HINT:
- As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
- When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.
- As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
Connect the connectors.
|
|
||||
| OK | |
| 10. READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select "Data List" and read the value displayed on the intelligent tester (Click here).
Data List: ABS Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
RR Wheel Speed
Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Speed indicated on speedometer
RL Wheel Speed
Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Speed indicated on speedometer
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
- OK:
- The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed.
- HINT:
- It is suspected that the DTCs were output due to a bad connection of the connector terminal.
- If troubleshooting has been carried out according to the "PROBLEM SYMPTOMS TABLE", refer back to the table and proceed to the next step (Click here).
- It is suspected that the DTCs were output due to a bad connection of the connector terminal.
|
|
||||
| OK | |
| 11. RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.
Check if the same DTCs are recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output
A
DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE)
B
DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the DTC CHART)
C
|
|
||||
|
|
||||
| A | |
| 12. INSPECT SPEED SENSOR ROTOR |
Turn the ignition switch off.
Remove the rear axle (Click here).
Check the rotor.
- OK:
- No scratches, cracks, oil, or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
Install the rear axle (Click here).
|
|
||||
| OK | ||
| ||
