Radio Broadcast cannot be Received or Poor Reception
Circuit diagnosis · Vehicles built from Jun 2009
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK RADIO AND DISPLAY ASSEMBLY |
Check the radio automatic station search function.
Check the radio automatic station search function by activating it.
- Result:
Result
Proceed to
Automatic station search function does not stop
A
Automatic station search function stops on a station
B
(for 2GR-FE RHD)
C
(except 2GR-FE RHD)
|
|
||||
|
|
||||
| A | |
| 2. CHECK OPTIONAL COMPONENTS |
Check optional components (sunshade film, telephone antenna, etc.).
Check if any optional components that may decrease reception capacity, such as sunshade film or a telephone antenna, are installed.
- Result:
Result
Proceed to
Optional components are installed
A
Optional components are not installed
B
- NOTICE:
- Do not remove any optional components installed by the customer without his or her consent.
|
|
||||
| A | ||
| ||
| 3. CHECK RADIO AND DISPLAY ASSEMBLY |
Preparation for check

Remove the antenna plug from the radio and display assembly.
Check for noise
Turn the ignition switch on (ACC) with the radio and display assembly connector connected.
Turn the radio on and tune into AM mode.
Place a screwdriver, thin wire or other metal object on the radio and display assembly antenna jack and check that noise can be heard from the speaker.
- OK:
- Noise can be heard from the speaker.
- Result:
Result
Proceed to
OK
A
NG
(for 2GR-FE RHD)
B
NG
(except 2GR-FE RHD)
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY ASSEMBLY - ANTENNA AMPLIFIER) |
Disconnect the F6 radio and display assembly connector.
Disconnect the F15 antenna amplifier connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F6-8 (ANT) - F15-1 (B)
Always
Below 1 Ω
F6-8 (ANT) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. INSPECT RADIO AND DISPLAY ASSEMBLY |
Reconnect the F6 radio and display assembly connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Condition
Specified Condition
F15-1 (B) - Body ground
Ignition switch on (IG)
Radio switch on
11 to 14 V
- Result:
Result
Proceed to
OK
A
NG
(for 2GR-FE RHD)
B
NG
(except 2GR-FE RHD)
C
Text in Illustration *1
Front view of wire harness connector
(to Antenna Amplifier)
|
|
||||
|
|
||||
| A | |
| 6. CHECK ANTENNA CORD |
Remove the antenna plug of the radio and display assembly and antenna.
Measure the resistance between the antenna and radio and display assembly to check for an open circuit in the antenna cord.
- Standard Resistance:
- Below 1 Ω
Measure the resistance between the antenna cord and body ground to check for a short circuit in the antenna cord.
- Standard Resistance:
- 10 kΩ or higher
- Result:
Result
Proceed to
OK
A
NG
(for 2GR-FE RHD)
B
NG
(except 2GR-FE RHD)
C
|
|
||||
|
|
||||
| A | |
| 7. REPLACE ANTENNA AMPLIFIER |
Replace the antenna amplifier and check if radio broadcasts can be received normally (Click here).
- OK:
- Radio broadcasts can be received.
- Result:
Result
Proceed to
OK
A
NG
(for 2GR-FE RHD)
B
NG
(except 2GR-FE RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
