DTC C1237/37 Speed Sensor Rotor Faulty |
| DTC No. | DTC Detecting Condition | Trouble Area |
| C1237/37 | When any of the following is detected:
|
|


| 1.CHECK TIRES |
Check the size and condition of all 4 tires .
|
| ||||
| OK | |
| 2.INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS |
![]() |
Disconnect the skid control ECU connector.
Connect the oscilloscope to each speed sensor terminal of the skid control ECU connector.
| Connector | Circuit |
| A25-5 (FL+) - A25-6 (FL-) | Front left speed sensor |
| A25-10 (FR+) - A25-9 (FR-) | Front right speed sensor |
| A25-7 (RL+) - A25-17 (RL-) | Rear left speed sensor |
| A25-19 (RR+) - A25-8 (RR-) | Rear right speed sensor |
![]() |
Check that a waveform is output when the tires are rotated (by the sensor circuit).
Make sure that the waveform does not change while jiggling a connector or a wire harness.
Connect the connector.
|
| ||||
| OK | |
| 3.RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at a speed of 32 km/h (20 mph) or more for 60 seconds or more.
Check if the same DTC is recorded (Click here).
| Condition | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK SPEED SENSOR ROTOR |
Check the speed sensor rotor.
Front Speed Sensor Rotor: (Click here)
Rear Speed Sensor Rotor: (Click here)
|
| ||||
| OK | |
| 5.CHECK SPEED SENSOR TIP |
Remove each speed sensor.
Check the speed sensor tip.
Install the speed sensor.
|
| ||||
| OK | |
| 6.INSPECT EACH SPEED SENSOR |
![]() |
Disconnect each speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A14-1 (FL+) - A14-2 (FL-) | Always | 1.4 to 1.8 kΩ at 20°C (68°F) |
| A14-1 (FL+) - Body ground | Always | 10 kΩ or higher |
| A14-2 (FL-) - Body ground | Always | 10 kΩ or higher |
| A35-1 (FR+) - A35-2 (FR-) | Always | 1.4 to 1.8 kΩ at 20°C (68°F) |
| A35-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| A35-2 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| g1-1 (RL+) - g1-2 (RL-) | Always | Below 2.2 kΩ |
| g1-1 (RL+) - Body ground | Always | 10 kΩ or higher |
| g1-2 (RL-) - Body ground | Always | 10 kΩ or higher |
| f1-1 (RR+) - f1-2 (RR-) | Always | Below 2.2 kΩ |
| f1-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| f1-2 (RR-) - Body ground | Always | 10 kΩ or higher |
Connect the connector.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU TO EACH SPEED SENSOR) |
![]() |
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A25-5 (FL+) - A14-1 (FL+) | Always | Below 1 Ω |
| A25-6 (FL-) - A14-2 (FL-) | Always | Below 1 Ω |
| A25-10 (FR+) - A35-1 (FR+) | Always | Below 1 Ω |
| A25-9 (FR-) - A35-2 (FR-) | Always | Below 1 Ω |
| A25-5 (FL+) - Body ground | Always | 10 kΩ or higher |
| A25-6 (FL-) - Body ground | Always | 10 kΩ or higher |
| A25-10 (FR+) - Body ground | Always | 10 kΩ or higher |
| A25-9 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A25-7 (RL+) - g1-1 (RL+) | Always | Below 1 Ω |
| A25-17 (RL-) - g1-2 (RL-) | Always | Below 1 Ω |
| A25-19 (RR+) - f1-1 (RR+) | Always | Below 1 Ω |
| A25-8 (RR-) - f1-2 (RR-) | Always | Below 1 Ω |
| A25-7 (RL+) - Body ground | Always | 10 kΩ or higher |
| A25-17 (RL-) - Body ground | Always | 10 kΩ or higher |
| A25-19 (RR+) - Body ground | Always | 10 kΩ or higher |
| A25-8 (RR-) - Body ground | Always | 10 kΩ or higher |
Connect the connector.
|
| ||||
| OK | |
| 8.RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at the speed of 32 km/h (20 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Condition | Proceed to |
| DTC (C1237/37) is not output | A |
| DTC (C1237/37) is output | B |
|
| ||||
| A | ||
| ||