DTC C0210/33 Right Rear Wheel Speed Sensor Signal Malfunction |
DTC C0215/34 Left Rear Wheel Speed Sensor Signal Malfunction |
DTC C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
DTC C1277/77 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278/78 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
DTC C1332/38 Right Rear Speed Sensor Circuit |
DTC C1333/39 Left Rear Speed Sensor Circuit |
| DTC No. | DTC Detecting Condition | Trouble Area |
| C0210/33 C0215/34 | When either of the following is detected:
|
|
| C1332/38 C1333/39 | Abnormality in the resistance value of each speed sensor is detected. |
|
| C1273/73 C1274/74 | Detected only during test mode. |
|
| C1277/77 C1278/78 | Detected only during test mode. |
|

| 1.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select "Data List" and read the value displayed on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition |
| RR Wheel Speed | Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed |
| RL Wheel Speed | Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK) |
Check if test mode (signal check) DTCs are detected (Click here).
| Condition | Proceed to |
| Test mode (signal check) DTC is not output | A |
| Test mode (signal check) DTC is output | B |
|
| ||||
| A | |
| 3.INSPECT SPEED SENSOR SIGNAL WAVEFORM |
![]() |
Lift up the vehicle.
Perform the inspection using an oscilloscope.
Disconnect the skid control ECU connector.
Connect the oscilloscope to terminals of the skid control ECU.
Check that a waveform is output when the tires are rotated.
Connect the connector.
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.
Check if the same DTCs are recorded (Click here).
| Condition | Proceed to |
| DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output | A |
| DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output (When troubleshooting in accordance with the PROBLEM SYMPTOMS TABLE) | B |
| DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output (When troubleshooting in accordance with the DTC CHART) | C |
|
| ||||
|
| ||||
| A | |
| 5.INSPECT SPEED SENSOR INSTALLATION |
![]() |
Check the rear speed sensor installation.
|
| ||||
| OK | |
| 6.INSPECT REAR SPEED SENSOR |
![]() |
Disconnect the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| g1-1 (RL+) - g1-2 (RL-) | Below 2.2 kΩ |
| g1-1 (RL+) - Body ground | 10 kΩ or higher |
| g1-2 (RL-) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| f1-1 (RR+) - f1-2 (RR-) | Below 2.2 kΩ |
| f1-1 (RR+) - Body ground | 10 kΩ or higher |
| f1-2 (RR-) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO SKID CONTROL ECU) |
![]() |
Check harness and connector.
Disconnect the skid control ECU connector.
Disconnect the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| A25-7 (RL+) - g1-1 (RL+) | Below 1 Ω |
| A25-17 (RL-) - g1-2 (RL-) | Below 1 Ω |
| g1-1 (RL+) - Body ground | 10 kΩ or higher |
| g1-2 (RL-) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| A25-19 (RR+) - f1-1 (RR+) | Below 1 Ω |
| A25-8 (RR-) - f1-2 (RR-) | Below 1 Ω |
| f1-1 (RR+) - Body ground | 10 kΩ or higher |
| f1-2 (RR-) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE TO REAR SPEED SENSOR) |
![]() |
Check harness and connector (skid control sensor wire).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| g1-1 - A-1 | Below 1 Ω |
| g1-1 - A-2 | 10 kΩ or higher |
| g1-1 - Body ground | 10 kΩ or higher |
| g1-2 - A-2 | Below 1 Ω |
| g1-2 - A-1 | 10 kΩ or higher |
| g1-2 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| f1-1 - A-1 | Below 1 Ω |
| f1-1 - A-2 | 10 kΩ or higher |
| f1-1 - Body ground | 10 kΩ or higher |
| f1-2 - A-2 | Below 1 Ω |
| f1-2 - A-1 | 10 kΩ or higher |
| f1-2 - Body ground | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.INSPECT SPEED SENSOR SIGNAL WAVEFORM |
![]() |
Lift up the vehicle.
Perform the inspection using the oscilloscope.
Disconnect the skid control ECU connector.
Connect the oscilloscope to terminals of the skid control ECU.
Check that a waveform is output when the tires are rotated.
Connect the connectors.
|
| ||||
| OK | |
| 10.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Connect the intelligent tester to the DLC3.
Start the engine.
Select "Data List" and read the value displayed on the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition |
| RR Wheel Speed | Wheel speed sensor (RR) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed |
| RL Wheel Speed | Wheel speed sensor (RL) reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph) | Actual wheel speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 11.RECONFIRM DTC |
Clear the DTCs (Click here).
Drive the vehicle at a speed of approximately 40 km/h (25 mph) or more for 60 seconds or more.
Check if the same DTCs are recorded (Click here).
| Condition | Proceed to |
| DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are output | A |
| DTCs (C0210/33, C0215/34, C1332/38 and C1333/39) are not output | B |
|
| ||||
| A | |
| 12.INSPECT SPEED SENSOR ROTOR |
Turn the ignition switch off.
Remove the rear axle (Click here).
Check the rotor.
Install the rear axle (Click here).
|
| ||||
| OK | ||
| ||