Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › CAMSHAFT › 2011.10–2015.04
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073927 CAMSHAFT A

2AR-FE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2.REMOVE FRONT WHEEL RH

Hide 53851Z 3.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 51441C 4.REMOVE ENGINE UNDER COVER RH

Hide 53736 5.REMOVE FRONT FENDER APRON SEAL RH

Hide 12601B 6.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 7.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 8.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 9.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 10.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 12327A 11.REMOVE NO. 2 ENGINE MOUNTING STAY RH

Hide 12309 12.REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

Hide 82121 13.DISCONNECT ENGINE WIRE

a.
A268654

Disconnect the connectors and clamps.


b.

Remove the bolts and nuts and disconnect the engine wire from the engine.


Hide 11201 15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 16.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A245326C07
1.073,1.104 1.906,0.354 1.906,0.354 2.927,1.135 true 1.042,1.354 1.833,1.865 1.833,1.865 2.979,1.375 true 1.635,3.229 2.667,3.833 2.667,3.833 2.844,3.833 true 1.823,0.177 2.135,0.375 0.313,0.198 10 false *a 1.75,1.865 2.073,2.063 0.323,0.198 10 false *b 2.896,3.771 3.208,3.969 0.313,0.198 10 false *c
*a Paint Mark
*b Timing mark
*c Timing Notch


Turn the crankshaft pulley until its timing notch (groove) and the timing mark "0" of the timing chain cover are aligned.


b.

Check that each timing mark of the camshaft timing gear and camshaft timing exhaust gear are aligned with each timing mark located as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.


c.

Place paint marks on the chain in alignment with the timing marks on the camshaft timing gear and camshaft timing exhaust gear.


Hide 11324 17.REMOVE TIMING CHAIN COVER PLATE

a.
A250986

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 13540 18.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A245327N15
1.958,0.198 2.229,0.375 0.271,0.177 10 10°

Turn the crankshaft approximately 10° clockwise.


b.
A249931N10
2.031,0.229 2.281,0.375 0.25,0.146 10 10°

Turn the crankshaft approximately 10° counterclockwise.


c.
A249932C09
1.854,1.969 1.635,1.708 false 1.896,1.948 2.125,2.094 0.229,0.146 10 *1
*1 Pin


Align the holes of the stopper plate and tensioner, and insert a pin into the stopper plate hole to lock the tensioner.


d.
A245327N15
1.958,0.198 2.229,0.375 0.271,0.177 10 10°

Turn the crankshaft approximately 10° clockwise.


e.
A249933

Remove the 2 bolts, chain tensioner and gasket.

NOTICE:

Make sure not to drop the gasket inside the timing chain cover.



f.
A249931N10
2.031,0.229 2.281,0.375 0.25,0.146 10 10°

Turn the crankshaft approximately 10° counterclockwise.


Hide 20.REMOVE TIMING CHAIN COVER TIGHT PLUG

Hide 13050 21.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A249934

Hold the hexagonal portion of the camshaft with a wrench and remove the bolt from the camshaft.

NOTICE:

Be careful not to damage the cylinder head or spark plug tube with the wrench.



b.
A249936

Separate the camshaft timing gear assembly from the camshaft.


c.
A249937C07
1.179,2.967 1.385,3.134 0.206,0.167 10 *a 2.693,2.023 2.899,2.19 0.206,0.167 10 *a 1.224,2.023 1.431,2.19 0.206,0.167 10 *b 2.758,2.967 2.964,3.134 0.206,0.167 10 *b
*a Narrow
*b Wide


Remove the timing chain from the camshaft timing gear assembly, and turn the camshaft timing gear assembly approximately 180°.


d.
A249938

Remove the camshaft timing gear assembly.

NOTICE:

Do not disassemble the camshaft timing gear.



Hide 22.REMOVE CAMSHAFT BEARING CAP

a.
A284105N09
0.563,1.823 0.719,2.021 0.156,0.198 10 1 0.604,0 0.76,0.198 0.156,0.198 10 2 0.167,1.125 0.323,1.323 0.156,0.198 10 3 2.833,0.021 2.99,0.219 0.156,0.198 10 4 2.938,1.531 3.094,1.729 0.156,0.198 10 5 1.167,0.031 1.323,0.229 0.156,0.198 10 6 1.146,1.542 1.302,1.74 0.156,0.198 10 7 2.281,0.021 2.438,0.219 0.156,0.198 10 8 2.333,1.531 2.49,1.729 0.156,0.198 10 9 1.688,0.021 2,0.219 0.313,0.198 10 10 1.688,1.542 2,1.74 0.313,0.198 10 11

Using several steps, remove the 11 bearing cap bolts in the sequence shown in the illustration.


b.
A284106N10
0.552,1.938 0.708,2.135 0.156,0.198 10 1 0.594,0.313 0.75,0.51 0.156,0.198 10 2 2.948,1.781 3.104,1.979 0.156,0.198 10 3 2.885,0.354 3.042,0.552 0.156,0.198 10 4 1.125,1.792 1.281,1.99 0.156,0.198 10 5 1.156,0.344 1.313,0.542 0.156,0.198 10 6 2.344,1.792 2.5,1.99 0.156,0.198 10 7 2.313,0.344 2.469,0.542 0.156,0.198 10 8 1.74,1.781 1.896,1.979 0.156,0.198 10 9 1.698,0.344 2.01,0.542 0.313,0.198 10 10

Using several steps, remove the 10 bearing cap bolts in the sequence shown in the illustration.


c.

Remove the 5 bearing caps.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 23.REMOVE CAMSHAFT

a.
A249939

Remove the camshaft from the camshaft housing.


Hide 13512 24.REMOVE NO. 2 CAMSHAFT

a.
A249940

Hold up the chain and remove the No. 2 camshaft from the camshaft housing.


b.
A249941

Suspend the chain with a string or equivalent as shown in the illustration.

NOTICE:

Be careful not to drop the chain inside the timing chain cover.



Hide 13070A 25.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A250991

Remove the flange bolt and camshaft timing exhaust gear assembly.

NOTICE:

Do not disassemble the camshaft timing exhaust gear.



Hide 15678A 26.REMOVE OIL CONTROL VALVE FILTER

Hide 11811 27.REMOVE NO. 1 CAMSHAFT BEARING

Hide 11821 28.REMOVE NO. 2 CAMSHAFT BEARING