Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE UNIT
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073932 ENGINE UNIT A

2AR-FE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE ENGINE COVER JOINT

a.
A196900

Remove the 3 joints.


Hide 11101J 3.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 11102A 4.REMOVE CAMSHAFT POSITION SENSOR

Hide 12108 5.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly from the cylinder head.


b.

Remove the gasket from the oil filler cap sub-assembly.


Hide 11301K 6.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12204 7.REMOVE VENTILATION VALVE SUB-ASSEMBLY

Hide 12205 8.REMOVE VENTILATION CASE SUB-ASSEMBLY

a.
A210185

Remove the 8 bolts and 2 nuts.


b.
A210186

Remove the ventilation case sub-assembly by prying between the ventilation case sub-assembly and cylinder block with a screwdriver.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and ventilation case sub-assembly.



Hide 12215 9.REMOVE SEPARATOR CASE

a.
A210188

Remove the 2 bolts, separator case and gasket.


Hide 16268 10.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A194876

Remove the bolt, 2 nuts, No. 1 water by-pass pipe and gasket.


Hide 16321 11.REMOVE WATER INLET

Hide 16620 13.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

a.
A196670

Remove the bolt and V-ribbed belt tensioner assembly.


Hide 16100 14.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 15710 15.REMOVE OIL COOLER ASSEMBLY (w/ Oil Cooler)

Hide 16323 16.REMOVE WATER INLET HOUSING

a.
A195872

Remove the 4 bolts, nut, water inlet housing and gasket.


Hide 13471 17.REMOVE CRANKSHAFT PULLEY

a.
A293510C06
1.323,0.99 0.583,0.865 0.583,0.865 1.219,0.635 true 0.552,0.271 0.865,0.427 0.313,0.156 10 false *a 2.417,1.677 2.729,1.833 0.313,0.156 10 false *b 0.323,0.781 1,1 0.677,0.219 10 false SST
*a Hold
*b Turn


Using SST, hold the crankshaft pulley and loosen the pulley bolt. Further loosen the bolt until 2 or 3 threads are screwed into the crankshaft.

SST
09213-54015  
09330-00021  

HINT:

SST (Crankshaft pulley holding tool) Fixing bolt part No. : 91551-80650(2 pcs)



b.
A195874C13
2.25,0.219 2.542,0.688 false 1.813,0.875 1.469,1.083 false 1.313,1.094 1.729,1.344 0.417,0.25 10 false SST 2.063,0.115 2.281,0.302 0.219,0.188 10 false *1 0.333,1.979 0.615,2.188 0.281,0.208 10 false *a 1.219,3.177 1.49,3.354 0.271,0.177 10 false *b
*1 Pulley Bolt
*a Hold
*b Turn


Using SST and the pulley bolt, remove the crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05011)

HINT:

Apply a lubricant to the threads and end of SST.



Hide 11201 18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A195876

Remove the 16 bolts, 3 seal washers, cylinder head cover sub-assembly and gasket.


b.
A196857

Remove the 3 gaskets from the camshaft bearing caps.


Hide 11193 19.REMOVE SPARK PLUG TUBE GASKET

a.
A195877

Using a screwdriver, pry out the 4 plug tube gaskets.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12315A 20.REMOVE ENGINE MOUNTING BRACKET RH

Hide 11302 21.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 22.REMOVE TIMING CHAIN COVER TIGHT PLUG

a.
A196859

Using a 14 mm hexagon wrench, remove the plug and gasket.


Hide 11324 23.REMOVE TIMING CHAIN COVER PLATE

a.
A196860

Remove the 4 bolts, timing chain cover plate and gasket.


Hide 11301C 24.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 25.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13540 27.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13559 28.REMOVE CHAIN TENSIONER SLIPPER

Hide 13506 29.REMOVE CHAIN SUB-ASSEMBLY

a.

Remove the chain sub-assembly.


Hide 13561 30.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13521 31.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A196881

Remove the crankshaft timing sprocket from the crankshaft.


Hide 13050 32.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 33.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 11103 34.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 15678A 36.REMOVE OIL CONTROL VALVE FILTER

a.
A196915

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 11811 38.REMOVE NO. 1 CAMSHAFT BEARING

a.
A196916

Remove the No. 1 camshaft bearing.


Hide 11821 39.REMOVE NO. 2 CAMSHAFT BEARING

a.
A196917

Remove the No. 2 camshaft bearing.


Hide 40.REMOVE CAMSHAFT HOUSING STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 11151A 41.REMOVE CAMSHAFT BEARING CAP SETTING RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


Hide 11114A 42.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


Hide 13801 43.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 44.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 46.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11445 48.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A196938

Remove the cylinder block water jacket spacer from the cylinder block.

NOTICE:

Be sure to remove the water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block is inverted.



Hide 12101 50.REMOVE OIL PAN SUB-ASSEMBLY

a.
A210204C08
0.76,1.198 1.771,1.417 1.771,1.417 1.49,1.833 false 1.823,1.375 2.063,1.521 0.24,0.146 10 false *1
*1 Nut


Remove the 11 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the oil pan and stiffening crankcase, cut off the applied sealer and remove the oil pan.

NOTICE:
·

Be careful not to damage the stiffening crankcase contact surface of the oil pan.

·

Be careful not to damage the stiffening crankcase flange.




Hide 15104 51.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A196919

Remove the 3 bolts, oil strainer and gasket.


Hide 12121 52.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A196920

Remove the 5 bolts and oil pan baffle plate.


Hide 13411 53.INSPECT CRANKSHAFT BACKLASH

a.
A196931

Using a dial indicator, measure the backlash of the crankshaft and balance shaft as shown in the illustration.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


Maximum backlash:

0.20 mm (0.00787 in.)


If the backlash is more than the maximum, replace the engine balancer assembly.


Hide 13620B 54.REMOVE ENGINE BALANCER ASSEMBLY

a.
A196921

Remove the 7 bolts and engine balancer.

NOTICE:

Do not disassemble the engine balancer.



Hide 55.INSPECT BALANCE SHAFT THRUST CLEARANCE

Hide 11420 56.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A196933

Remove the 7 bolts.


b.
A196934C08
0.031,0 0.281,0.26 0.25,0.26 10 false *a 0.031,2.135 0.375,2.438 0.344,0.302 10 false *b
*a LH Side
*b RH Side


Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase and cylinder block at the places shown in the illustration.

HINT:

Tape the screwdriver tip before use.


NOTICE:

Be careful not to damage the contact surfaces of the cylinder block and stiffening crankcase assembly.



Hide 57.REMOVE STIFFENING CRANKCASE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 58.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove the ring pin unless it is being replaced.


Hide 11401L 59.REMOVE REAR ENGINE OIL SEAL

a.
A196937

Remove the rear engine oil seal from the cylinder block.