64607
1.INSTALL LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY
Install the luggage door lock control cable sub-assembly to the fuel lid lock control cable sub-assembly with the clamp and the 3 pieces of tape as shown in the illustration.
| *1 | Clamp (A) | *2 | Clamp |
| *3 | Luggage Door Lock Control Cable Sub-assembly | *4 | Fuel Lid Lock Control Cable Sub-assembly |
| *5 | Tape | - | - |
| Area | Measurement | Area | Measurement |
|---|---|---|---|
| a | 295 to 305 mm (11.6 to 12.0 in.) | b | 880 to 900 mm (2.29 to 2.95 ft.) |
| c | 2090 to 2110 mm (6.86 to 6.92 ft.) | d | 2970 to 2990 mm (8.86 to 9.81 ft.) |
| e | 5.0 mm (0.197 in.) or less | - | - |
Wrap tape around the designated position 1 to 3 times.
Make sure that the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly are not kinked.
Engage the 10 clamps and install the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.
| *1 | Cutout |
| *2 | Guide <C> |
Align the cutouts and guides <C>, and then insert the fuel filler opening lid lock retainer.
| *1 | Claw |
Engage the 2 claws and install the fuel filler opening lid lock retainer.
Engage the 2 claws and install the fuel lid lock control cable sub-assembly.
w/ Wireless Door Lock Control System:
Engage the clamp and connect the luggage door lock control cable sub-assembly.
Connect the luggage door lock control cable sub-assembly.
Engage the guide as shown in the illustration.
w/o Wireless Door Lock Control System:
Engage the 3 clamps and connect the luggage door lock control cable sub-assembly.
Connect the luggage door lock control cable sub-assembly to the luggage compartment door lock cylinder assembly.
Return the floor carpet to the original position.
Engage the 2 clamps and install the 2 scuff plate clips.
Engage the 3 clamps and connect the wire harness.
77306
2.INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
| *1 | Luggage Door Lock Control Cable Sub-assembly |
| *2 | Fuel Lid Lock Control Cable Sub-assembly |
Connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly to the fuel lid lock open lever sub-assembly.
Engage the guide and install the fuel lid lock open lever sub-assembly as shown in the illustration.
Install the screw.
64722
3.INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH
64725D
4.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
| *1 | Pin |
Engage the pin to install the No. 1 luggage compartment trim hook.
58387
5.INSTALL REAR FLOOR FINISH PLATE
64711
6.INSTALL LUGGAGE COMPARTMENT FLOOR MAT
64719A
7.INSTALL LUGGAGE COMPARTMENT DOOR COVER
8.INSTALL REAR SEATBACK ASSEMBLY (for Fixed Seat Type)
9.INSTALL REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)
72693
10.INSTALL REAR SEAT CUSHION LOCK HOOK (for Fixed Seat Type)
11.INSTALL REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)
72693
12.INSTALL REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)
13.INSTALL REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)
62414A
14.INSTALL CENTER PILLAR LOWER GARNISH LH
73220
15.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH
73233
16.INSTALL LAP BELT OUTER ANCHOR COVER
62332A
17.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
67918A
18.INSTALL REAR DOOR SCUFF PLATE LH
62312B
19.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
67914
20.INSTALL FRONT DOOR SCUFF PLATE LH
21.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
22.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)