Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY(for RHD)
RM19V0EQ _59 Vehicle Exterior _014618 DOOR / HATCH _0074230 FUEL LID LOCK CONTROL CABLE ASSEMBLY(for RHD) A

DOOR / HATCH  FUEL LID LOCK CONTROL CABLE ASSEMBLY(for RHD)  INSTALLATION  


PROCEDURE

Hide 77035 1.INSTALL FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

a.

Engage the 7 clamps and install the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.


b.
B291310C08
2.052,2.219 1.792,2.083 false 2.135,2.719 2.063,2.896 false 1.729,0.896 2.406,0.375 false 1.833,1.167 2.438,1.448 false 2.438,0.25 2.719,0.49 0.281,0.24 10 false *1 2.458,1.385 2.833,1.698 0.375,0.313 10 false *1 1.604,1.979 1.875,2.292 0.271,0.313 10 false *2 1.958,2.896 2.208,3.156 0.25,0.26 10 false *2
*1 Cutout
*2 Guide <C>


Align the cutouts and guides <C>, and then insert the fuel filler opening lid lock retainer.


c.
B291312C09
1.958,2.865 2.219,2.979 false 2.26,2.927 2.542,3.188 0.281,0.26 10 false *1
*1 Claw


Engage the 2 claws and install the fuel filler opening lid lock retainer.


d.
B280601

Engage the 2 claws and install the fuel lid lock control cable sub-assembly.


e.

Install a new No. 2 noise control plate.


f.
B281716C04
1.667,1.698 1.417,1.896 1.417,1.896 2.125,1.688 false 0.948,1.698 0.781,1.917 false 0.906,1.635 1.146,1.427 false 1.229,1.813 1.531,2.156 0.302,0.344 10 *1 1.167,1.302 1.49,1.552 0.323,0.25 10 *3 0.656,1.917 0.927,2.198 0.271,0.281 10 *2 1.052,0.979 1.333,1.26 0.281,0.281 10 a 1.302,0.417 1.563,0.688 0.26,0.271 10 b
*1 Tape
*2 Fuel Lid Lock Control Cable Sub-assembly
*3 Luggage Door Lock Control Cable Sub-assembly


Install the fuel lid lock control cable sub-assembly to the luggage door lock control cable sub-assembly with the 2 pieces of tape as shown in the illustration.

Reference Measurement
Area Measurement
a 295 to 305 mm (11.6 to 12.0 in.)
b 935 to 955 mm (36.8 to 37.6 in.)

NOTICE:
·

Wrap tape around the designated position 1 to 3 times.

·

Make sure that the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly are not kinked.




g.

Return the floor carpet to the original position.


h.

Engage the 2 clamps and install the 2 scuff plate clips.


i.

Engage the 3 clamps and connect the wire harness.


Hide 77306 2.INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

Hide 64722 3.INSTALL LUGGAGE COMPARTMENT INNER TRIM COVER LH

Hide 64725D 4.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 58387 5.INSTALL REAR FLOOR FINISH PLATE

Hide 64711 6.INSTALL LUGGAGE COMPARTMENT FLOOR MAT

Hide 7.INSTALL REAR SIDE SEATBACK ASSEMBLY LH

Hide 72693 8.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 67918A 10.INSTALL REAR DOOR SCUFF PLATE LH

Hide 62413A 11.INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 73210 12.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>INSTALLATION


Hide 73233 13.INSTALL LAP BELT OUTER ANCHOR COVER

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>INSTALLATION


Hide 62331A 14.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

Hide 67917A 15.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 62311B 16.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 67913 17.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION


Hide 18.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)

Hide 19.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)