Home › Vehicle Exterior › DOOR / HATCH › FUEL LID LOCK CONTROL CABLE ASSEMBLY(for RHD)
RM19V0EQ _59 Vehicle Exterior _014618 DOOR / HATCH _0074230 FUEL LID LOCK CONTROL CABLE ASSEMBLY(for RHD) A

DOOR / HATCH  FUEL LID LOCK CONTROL CABLE ASSEMBLY(for RHD)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

Hide 3.REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)

Hide 67913 4.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL


Hide 67917A 6.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62331A 7.DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL


Hide 73233 8.REMOVE LAP BELT OUTER ANCHOR COVER

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL


Hide 73210 9.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>SEAT BELT>FRONT SEAT OUTER BELT ASSEMBLY>REMOVAL


Hide 62413A 10.REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 67918A 11.REMOVE REAR DOOR SCUFF PLATE LH

Hide 12.REMOVE REAR SEAT CUSHION ASSEMBLY

Hide 72693 13.REMOVE REAR SEAT CUSHION LOCK HOOK

Hide 14.REMOVE REAR SIDE SEATBACK ASSEMBLY LH

Hide 64711 15.REMOVE LUGGAGE COMPARTMENT FLOOR MAT

Hide 58387 16.REMOVE REAR FLOOR FINISH PLATE

Hide 64725D 17.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 64722 18.REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH

Hide 77306 19.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY

Hide 77035 20.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY

a.
B281746

Disengage the 2 clamps.


b.
B281747

Disengage the clamp and disconnect the wire harness.


c.
B281748

Disengage the 2 clamps and remove the 2 scuff plate clips.


d.

Turn back the floor carpet so that the fuel lid lock control cable sub-assembly can be removed.


e.
B281715C07
1.708,0.521 2.469,0.198 2.469,0.198 2.198,0.521 false 0.969,0.24 1.281,0.552 false 0.99,0.896 1.281,0.604 false 2.49,0.083 2.667,0.26 0.177,0.177 10 false *1 0.813,0.135 0.99,0.313 0.177,0.177 10 false *3 0.833,0.823 1.01,1 0.177,0.177 10 false *2
*1 Tape
*2 Fuel Lid Lock Control Cable Sub-assembly
*3 Luggage Door Lock Control Cable Sub-assembly


Remove the 2 pieces of tape that connect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.


f.
B281719

Remove the No. 2 noise control plate.


g.
B287079C10
1.667,0.979 1.958,0.646 false 1.781,1.24 2.469,1.729 false 1.958,2.885 2.302,2.99 false 1.99,0.479 2.406,0.792 0.417,0.313 10 *1 2.521,1.74 2.823,2.052 0.302,0.313 10 *1 2.354,2.927 2.792,3.354 0.438,0.427 10 *2
*1 Cutout
*2 Guide <A>


Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides <A>, and then pull the fuel filler opening lid lock retainer.


h.
B288519C09
1.698,0.969 1.26,0.885 false 1.802,1.25 2.458,1.594 false 2.208,2.385 1.938,2.25 false 2.292,2.875 2.26,3.052 false 1.063,0.802 1.333,1.052 0.271,0.25 10 *1 2.51,1.552 2.885,1.927 0.375,0.375 10 *1 1.74,2.146 2.01,2.406 0.271,0.26 10 *2 2.156,3.052 2.427,3.302 0.271,0.25 10 *2
*1 Cutout
*2 Guide <B>


Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides <B>, and then pull the fuel filler opening lid lock retainer.


i.
B287067C09
1.719,0.865 1.99,0.604 false 1.823,1.156 2.26,1.24 false 1.531,0.979 1.219,0.656 false 1.594,1.188 1.688,1.458 false 1.385,1.031 0.854,0.813 false 1.51,1.729 1.438,1.25 false 2,0.479 2.333,0.802 0.333,0.323 10 false *1 1.063,0.552 1.365,0.792 0.302,0.24 10 false *2 1.615,1.448 1.906,1.677 0.292,0.229 10 false *2 2.302,1.146 2.635,1.427 0.333,0.281 10 false *1 0.688,0.708 0.99,1.01 0.302,0.302 10 false *3 1.448,1.729 1.74,2.021 0.292,0.292 10 false *3
*1 Cutout
*2 Guide <C>
*3 Guide <B>


Pull out the fuel filler opening lid lock retainer with both guides <B> and <C> aligned with the cutouts.


j.
B287069

Disengage the 2 claws and remove the fuel filler opening lid lock retainer.


k.

Disengage the 7 clamps and remove the fuel lid lock control cable sub-assembly.

B281720C03
0.531,0.583 0.479,0.833 false 0.521,0.49 0.354,0.406 false 2.125,5.094 2.365,4.958 false 3.385,5.083 3.583,4.948 false 6.813,5.063 6.885,5.177 false 6.573,0.583 6.844,0.604 false 3.76,0.573 4.021,0.51 false 2.771,0.51 2.521,0.563 false 0.396,0.844 0.656,1.073 0.26,0.229 10 false *1 0.208,0.323 0.469,0.583 0.26,0.26 10 false *2 1.979,5.01 2.25,5.271 0.271,0.26 10 false *1 3.24,5.021 3.521,5.26 0.281,0.24 10 false *1 6.833,5.188 7.063,5.406 0.229,0.219 10 false *1 6.854,0.5 7.125,0.74 0.271,0.24 10 false *1 3.625,0.49 3.917,0.75 0.292,0.26 10 false *1 2.375,0.469 2.656,0.719 0.281,0.25 10 false *1
*1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly