Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING › 2011.10–2015.04
RM19V0EQ _58 Vehicle Interior _014615 INTERIOR PANELS / TRIM _0074201 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B395175N01
2.615,1.542 2.771,1.74 0.156,0.198 10 false A 1.021,0.677 1.177,0.875 0.156,0.198 10 false A 0.229,0.948 0.385,1.146 0.156,0.198 10 false B 1.917,2.656 2.073,2.854 0.156,0.198 10 true B 2.698,0.396 2.854,0.594 0.156,0.198 10 false C 0.667,1.896 0.823,2.094 0.156,0.198 10 false C 1.365,0.479 1.521,0.677 0.156,0.198 10 false 1 2.938,1.365 3.094,1.563 0.156,0.198 10 false 1 0.573,0.573 0.729,0.771 0.156,0.198 10 false 2 2.292,2.344 2.448,2.542 0.156,0.198 10 false 2

Disengage the 2 claws (A) in the direction indicated by the arrows (1) shown in the illustration.


b.

Disengage the 2 claws (B) in the direction indicated by the arrows (2) shown in the illustration.


c.

Disengage the 6 claws (C) to remove the front door scuff plate LH.


Hide 62112A 4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

a.
B278978

Remove the clip.


b.

Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.


Hide 62312B 5.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Remove the front door opening trim weatherstrip LH.


Hide 62212 6.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

a.
B294183E01
0.844,1.458 1.271,1.76 0.427,0.302 10 false (1) 2.177,1.323 2.688,1.635 0.51,0.313 10 false (2)

Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.


b.

Disengage the 2 guides and remove the front pillar garnish LH.


Hide 62212 7.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

a.
B278985C03
2.49,0.74 2.583,0.448 false 2.375,0.771 2.771,1.042 0.396,0.271 10 false *1
*1 Front Pillar Garnish Clip


Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.

HINT:

Make the front pillar garnish LH hang down from the front pillar garnish clip.



b.
B278986E01
1.896,1.427 2.396,1.75 0.5,0.323 10 false (B) 0.646,0.813 1.156,1.115 0.51,0.302 10 false (A) 0.927,0.115 1.438,0.406 0.51,0.292 10 false (A)

While pushing the tabs on the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.


c.

Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.


d.
B298426C02
2.365,0.979 2.677,0.885 false 1.635,0.656 2.156,0.521 false 1.417,1.198 1.417,1.646 false 2.177,0.396 2.51,0.646 0.333,0.25 10 false *2 1.333,1.646 1.792,1.896 0.458,0.25 10 false *3 2.698,0.75 3.052,1.01 0.354,0.26 10 false *1
*1 Adhesive Tape
*2 Protective Cover
*3 Curtain Shield Airbag Assembly


Protect the curtain shield airbag assembly.

i.

Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

NOTICE:

Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.




Hide 67913 8.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111A 9.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 10.REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 11.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 12.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

Hide 72693 13.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fixed Seat Type)

Hide 14.REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

Hide 15.REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

Hide 72693 16.REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

Hide 17.REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

Hide 18.REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

Hide 19.REMOVE REAR SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

Hide 20.REMOVE REAR SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

Hide 67918A 21.REMOVE REAR DOOR SCUFF PLATE LH

a.
B395176N01
0.208,0.906 0.365,1.104 0.156,0.198 10 false A 0.271,2.354 0.427,2.552 0.156,0.198 10 false B 0.5,0.708 0.656,0.906 0.156,0.198 10 false 1 0.615,2.01 0.771,2.208 0.156,0.198 10 false 2 1.135,2.771 1.292,2.969 0.156,0.198 10 false C 2.969,1.75 3.125,1.948 0.156,0.198 10 false C 1.729,0.646 1.885,0.844 0.156,0.198 10 false C 2.271,0.844 2.427,1.042 0.156,0.198 10 false C

Disengage the claw (A) in the direction indicated by the arrow (1) shown in the illustration.


b.

Disengage the claw (B) in the direction indicated by the arrow (2) shown in the illustration.


c.

Disengage the 4 claws (C) to remove the rear door scuff plate LH.

HINT:

Disengage the claws from the front side of the rear door scuff plate LH.



Hide 62332A 22.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.

Remove the rear door opening trim weatherstrip LH.


Hide 73233 23.REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

Hide 73220 24.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

Hide 62414A 25.REMOVE CENTER PILLAR LOWER GARNISH LH

a.
B278989

Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.


Hide 62412B 26.REMOVE CENTER PILLAR UPPER GARNISH LH

a.
B278990

Remove the 2 screws.


b.

Disengage the clip.


c.

Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.


Hide 62472A 27.REMOVE ROOF SIDE INNER GARNISH LH

a.
B278991

Disengage the 5 clips.


b.

Disengage the guide and remove the roof side inner garnish LH.


Hide 67917A 28.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62331A 29.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 73233 30.REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 73210 31.DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62413A 32.REMOVE CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62411B 33.REMOVE CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62471A 34.REMOVE ROOF SIDE INNER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 35.REMOVE FRONT SEAT ASSEMBLY LH

Hide 36.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 37.REMOVE INSTRUMENT PANEL SAFETY PAD

Hide 87834 38.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 89943 39.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 63650A 40.REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)

Hide 63650A 41.REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)

Hide 81240 42.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)

Hide 81360T 43.REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

Hide 74610A 44.REMOVE ASSIST GRIP SUB-ASSEMBLY (for RH Side)

a.
B287232C03
1.844,1.052 1.281,0.604 false 1.052,0.49 1.469,0.75 0.417,0.26 10 false * 1
*1 Protective Tape


Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

NOTICE:

Do not forcibly pry the assist grip covers to prevent them from being deformed.


HINT:

Tape the screwdriver tip before use.



b.
B287236

Disengage the 2 clips and remove the assist grip sub-assembly.


c.

Remove the 2 clips from the vehicle body.


Hide 74610A 45.REMOVE ASSIST GRIP SUB-ASSEMBLY (for LH Side)

w/ Assist Grip:

HINT:

Use the same procedure for the RH side.


Hide 74630E 46.REMOVE REAR ASSIST GRIP ASSEMBLY LH

a.
B278997C06
1.677,1 2.042,0.646 false 2.063,0.49 2.5,0.76 0.438,0.271 10 false *1
*1 Protective Tape


Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.

NOTICE:

Do not forcibly pry the assist grip covers to prevent them from being deformed.


HINT:

Tape the screwdriver tip before use.



b.
B279000

Disengage the 2 clips and remove the rear assist grip assembly LH.


c.

Remove the 2 clips from the vehicle body.


Hide 74620C 47.REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63318C 48.REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

a.

Remove the sliding roof opening trim moulding.


Hide 74325 49.REMOVE VISOR BRACKET COVER (for LH Side)

a.
B278992

Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.


Hide 74320 50.REMOVE VISOR ASSEMBLY LH

a.
B278994

Remove the 2 screws and visor assembly LH.


Hide 74325 51.REMOVE VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 74310 52.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74348 53.REMOVE VISOR HOLDER

a.
B211697E01
1.094,0.292 1.563,0.563 0.469,0.271 10 false 45°

Turn the visor holder approximately 45° and pull it out as shown in the illustration.


b.

Disengage the 2 claws and remove the visor holder.

HINT:

Use the same procedure for the other visor holder.



Hide 54.REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

a.

w/ Rain Sensor:

i.

Disconnect the connector from the rain sensor.



b.

w/ EC Mirror:

i.

Disconnect the connector from the inner rear view mirror.



c.

Remove the bolt and disconnect the bracket from the front pillar RH.

B294894C01
5.26,4.219 5.667,4.521 0.406,0.302 12 false *A
*A w/ Digital Audio Broadcasting Antenna - -



d.

Disengage the 3 clamps from the front pillar RH.


e.

Disengage the 4 clamps from the front pillar LH.


f.

Disengage the 2 clamps and disconnect the connector from the rear pillar RH.


g.

w/ Digital Audio Broadcasting Antenna:

i.

Disengage the clamp and disconnect the connector from the rear pillar LH.



h.

Remove the 2 clips.


i.

Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

HINT:

Leave the 2 clips in the vehicle.



j.
B279009

Remove the roof headlining assembly from the vehicle through the front passenger side door.

NOTICE:

Do not damage the roof headlining assembly or body interior.



k.
B279104

Remove the 2 clips from the vehicle body as shown in the illustration.


Hide 55.REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

a.

w/ Rain Sensor:

i.

Disconnect the connector from the rain sensor.



b.

w/ EC Mirror:

i.

Disconnect the connector from the inner rear view mirror.



c.

Disconnect the connector from the sliding roof drive gear assembly.

B294895C02
5.25,4.208 5.719,4.5 0.469,0.292 12 false *A
*A w/ Digital Audio Broadcasting Antenna - -



d.

Remove the bolt and disconnect the bracket from the front pillar RH.


e.

Disengage the 3 clamps from the front pillar RH.


f.

Disengage the 4 clamps from the front pillar LH.


g.

Disengage the 2 clamps and disconnect the connector from the rear pillar RH.


h.

w/ Digital Audio Broadcasting Antenna:

i.

Disengage the clamp and disconnect the connector from the rear pillar LH.



i.

Remove the 2 clips.


j.

Disengage the 2 fasteners.


k.

Slide the roof headlining assembly to disengage the 2 clips as shown in the illustration.

HINT:

Leave the 2 clips in the vehicle.



l.
B279010

Remove the roof headlining assembly from the vehicle through the front passenger side door.

NOTICE:

Do not damage the roof headlining assembly or body interior.



m.
B279104

Remove the 2 clips from the vehicle body as shown in the illustration.