Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM19V0EQ _54 Brake _014591 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0076219 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1434  Steering Angle Sensor Output Malfunction  


DESCRIPTION

The skid control ECU receives signals from the steering angle sensor via the CAN communication system.

HINT:

If there is trouble in the bus lines between the steering angle sensor and the CAN communication system, DTC U0126 (Lost Communication with Steering Angle Sensor Module) is output. When U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0126 first.


DTCs may be stored if one of the following occurs:

·

Steering angle sensor zero point value malfunction.

·

Steering angle sensor signal malfunction.

·

Steering angle sensor signal stuck malfunction.

·

Steering angle sensor and the yaw rate sensor values inconsistent.

·

Steering angle sensor installation abnormality.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1434 Steering Angle Sensor Output Malfunction Any of the following is detected:
1.

The difference between zero point stored in the steering angle sensor and the estimated zero point exceeds 15 deg.

2.

The offset value of the steering angle sensor is -13.5 deg. or less or 13.5 deg. or more.

3.

The steering angle sensor value exceeds a specified value for 0.3 seconds or more.

4.

The change of the steering angle sensor value within 0.02 seconds is abnormal.

5.

The steering angle sensor value changes by less than 5 deg. and both left and right turns have been recognized.

6.

There is a difference between the skid control ECU estimated value and the steering angle sensor value due to an abnormal steering angle sensor value.


·

Sensor installation

·

Steering angle sensor power supply

·

Steering angle sensor

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C167662E74
0.135,4.01 0.458,4.177 0.323,0.167 10 false I29 0.896,3.302 1.417,3.604 0.521,0.302 10 false ESS 0.823,0.677 1.385,1 0.563,0.323 10 false CANL 0.792,1.271 1.406,1.625 0.615,0.354 10 false CANH 0.906,1.958 1.365,2.271 0.458,0.313 10 false BAT 1.021,2.635 1.24,2.802 0.219,0.167 10 false IG 1.281,0.552 1.479,0.74 0.198,0.188 10 false 2 1.281,1.115 1.469,1.302 0.188,0.188 10 false 3 1.281,1.833 1.406,2.021 0.125,0.188 10 false 5 1.281,2.51 1.385,2.698 0.104,0.188 10 false 4 1.281,3.167 1.385,3.354 0.104,0.188 10 false 1 2.667,1.833 2.802,2 0.135,0.167 10 false 1 2.198,1.833 2.333,2 0.135,0.167 10 false 2 2.073,2.073 3,2.229 0.927,0.156 10 false ECU-B NO. 1 2,2.771 3,2.927 1,0.156 10 false ECU-IG1 NO. 1 3.896,1.927 4.74,2.094 0.844,0.167 10 false from Battery 3.896,2.615 5.281,2.781 1.385,0.167 10 false from IG1 NO. 2 Relay 5.792,1.156 6.125,1.417 0.333,0.26 10 false 26 5.479,3.885 5.75,4.031 0.271,0.146 10 false A49 6.042,0.656 6.583,0.917 0.542,0.26 10 false CANL 6.042,1.26 6.51,1.552 0.469,0.292 10 false CANH 5.792,0.542 6.208,0.854 0.417,0.313 10 false 14 5.479,4.042 7.063,4.552 1.583,0.51 10 false Skid Control ECU (Brake Actuator Assembly) 0.135,4.146 1.604,4.323 1.469,0.177 10 false Steering Angle Sensor

CAUTION / NOTICE / HINT

HINT:
·

When U0073, U0123 and/or U0126 is output together with C1434, inspect and repair the trouble areas indicated by U0073, U0123 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073

·

When any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly) is malfunctioning, DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal. When DTCs for the speed sensors or yaw rate and acceleration sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor, inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


d.

Start the engine.


e.

Drive the vehicle at a speed of 35 km/h (22 mph) and turn the steering wheel to the right and left and then check that no speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
No CAN communication system, speed sensor, or yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output. A
CAN communication system DTC is output. B
Speed sensor and/or yaw rate and acceleration sensor (airbag sensor assembly) DTC is output. C


HINT:
·

If there is a malfunction in any of the speed sensors or the yaw rate and acceleration sensor (airbag sensor assembly), DTCs for the steering angle sensor may be stored even though the steering angle sensor is normal.

·

If speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair the sensors and then inspect the steering angle sensor.





A

2.CHECK STEERING ANGLE SENSOR INSTALLATION

B

C

2.CHECK STEERING ANGLE SENSOR INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the steering angle sensor has been installed properly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>INSTALLATION

OK:

The steering angle sensor installation are normal.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
C156493C10
0.323,1.063 0.792,1.365 0.469,0.302 2.156,2.656 2.594,3.073 false 1.958,2.552 2.594,2.104 false 0.333,0.25 0.604,0.51 0.271,0.26 10 *a 0.479,1.135 1.094,1.521 0.615,0.385 10 I29 2.677,1.99 2.917,2.177 0.24,0.188 10 IG 2.521,3.083 2.948,3.302 0.427,0.219 10 BAT
*a Front view of wire harness connector
(to Steering Angle Sensor)


Remove the steering wheel and the column cover.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the I29 steering angle sensor connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I29-5 (BAT) - Body ground Always 11 to 14 V
I29-4 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)
a.
C156493C11
0.333,1.135 0.802,1.438 0.469,0.302 1.281,2.667 0.865,3.042 false 0.281,0.208 0.583,0.594 0.302,0.385 10 *a 0.5,1.208 0.792,1.396 0.292,0.188 10 I29 0.656,3.052 1.021,3.24 0.365,0.188 10 ESS
*a Front view of wire harness connector
(to Steering Angle Sensor)


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I29-1 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)