The skid control ECU measures the speed of each wheel by receiving signals from the speed sensor.
These signals are used for recognizing that all four wheels are operating properly.
Therefore, all wheel signals must be equal.
DTCs C1275 to C1278 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1275 to C1278 are output only in Test Mode.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1237 | Speed Sensor Rotor Faulty | Any of the following is detected:
1.
Discrepancy among four wheel speed sensor output. 2.
Abnormal pulse signals from 3 or more sensors. 3.
Continuous ABS control is performed for 60 seconds or more. 4.
VSC control is performed for 5 seconds or more. |
·
Tire and wheel size ·
Tire deformation ·
Speed sensor rotor ·
Speed sensor ·
Speed sensor circuit ·
Skid control ECU (Brake actuator assembly) |
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH) |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | Front speed sensor rotor RH/LH (Front drive outboard joint shaft assembly RH/LH) |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) | Detected only during Test Mode. | Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) | Detected only during Test Mode. | Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH) |
DTC C1275 is for the front speed sensor RH.
DTC C1276 is for the front speed sensor LH.
DTC C1277 is for the rear speed sensor RH.
DTC C1278 is for the rear speed sensor LH.
Refer to DTCs C1330, C1331, C1332, C1333, C1464, C1465, C1466 and C1467.
for front: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271
for rear: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273
When C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 is output together with C1237, inspect and repair the trouble areas indicated by C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 first.
for front: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1271
for rear: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1273
Check the size and condition of all four wheels.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
The DTC is output when tire deformation or a difference in tire size is detected.
The diameter of all four tires and the tire pressure are the same.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List using the intelligent tester.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Tester Display |
|---|
| FR Wheel Speed |
| FL Wheel Speed |
| RR Wheel Speed |
| RL Wheel Speed |
Check the speed value output from the speed sensor displayed on the intelligent tester.
Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION
The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for front) | B |
| NG (for rear) | C |
A
B
C
Turn the ignition switch off.
Perform the sensor check using the Test Mode procedure.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Tester Display |
|---|
| Signal Check |
All Test Mode DTCs are not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for front) | B |
| NG (for rear) | C |
A
B
C
Turn the ignition switch off.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1237 is not output. | A |
| DTC C1237 is output (for front). | B |
| DTC C1237 is output (for rear). | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Remove the front speed sensor and the component with the sensor rotor.
for speed sensor: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
for sensor rotor: Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>REMOVAL
Check the speed sensor tip and speed sensor rotor.
No scratches, oil, or foreign matter on the sensor tip and rotor.
If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
If there are any ferrous metal filings stuck to the rotor, this will result in a malfunction, so confirm that the rotor is not contaminated with foreign matter before replacing the sensor.
Check the speed sensor signal after cleaning or replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the front speed sensor and the component with the sensor rotor.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the A49 skid control ECU connector and the A53 or A16 front speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-16 (FR+) - A53-1 (FR+) | Always | Below 1 Ω |
| A49-16 (FR+) - Body ground | Always | 10 kΩ or higher |
| A49-4 (FR-) - A53-2 (FR-) | Always | Below 1 Ω |
| A49-4 (FR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-19 (FL+) - A16-1 (FL+) | Always | Below 1 Ω |
| A49-19 (FL+) - Body ground | Always | 10 kΩ or higher |
| A49-8 (FL-) - A16-2 (FL-) | Always | Below 1 Ω |
| A49-8 (FL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A49 skid control ECU connector and the A53 or A16 front speed sensor connector.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Replace the front speed sensor.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B
Turn the ignition switch off.
Replace the front speed sensor rotor (front drive outboard joint shaft assembly).
Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>DISASSEMBLY
If the front speed sensor rotor needs to be replaced, replace the front drive outboard joint shaft assembly.
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B
| *A | for RH |
| *B | for LH |
| *a | Front view of skid control sensor wire |
| *b | Front view of wire harness connector
(to Sensor Side Connector) |
| *c | Front view of wire harness connector
(to Vehicle Side Connector) |
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Remove the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h1-2 (RR+) - hO1-1 (RR+) | Always | Below 1 Ω |
| h1-2 (RR+) - hO1-2 (RR-) | Always | 10 kΩ or higher |
| h1-2 (RR+) - Body ground | Always | 10 kΩ or higher |
| h1-1 (RR-) - hO1-2 (RR-) | Always | Below 1 Ω |
| h1-1 (RR-) - hO1-1 (RR+) | Always | 10 kΩ or higher |
| h1-1 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| i1-2 (RL+) - iN1-1 (RL+) | Always | Below 1 Ω |
| i1-2 (RL+) - iN1-2 (RL-) | Always | 10 kΩ or higher |
| i1-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| i1-1 (RL-) - iN1-2 (RL-) | Always | Below 1 Ω |
| i1-1 (RL-) - iN1-1 (RL+) | Always | 10 kΩ or higher |
| i1-1 (RL-) - Body ground | Always | 10 kΩ or higher |
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the A49 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-17 (RR+) - hO1-1 (RR+) | Always | Below 1 Ω |
| A49-17 (RR+) - Body ground | Always | 10 kΩ or higher |
| A49-29 (RR-) - hO1-2 (RR-) | Always | Below 1 Ω |
| A49-29 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A49-31 (RL+) - iN1-1 (RL+) | Always | Below 1 Ω |
| A49-31 (RL+) - Body ground | Always | 10 kΩ or higher |
| A49-18 (RL-) - iN1-2 (RL-) | Always | Below 1 Ω |
| A49-18 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the skid control sensor wire.
Reconnect the A49 skid control ECU connector.
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Replace the rear speed sensor rotor with rear speed sensor (rear axle hub and bearing assembly).
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL
The rear speed sensor rotor is incorporated into the rear axle hub and bearing assembly.
If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly with rear speed sensor.
Check the speed sensor signal after replacement.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 54 km/h (34 mph) or more for at least 120 seconds.
Check if the same DTC is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC C1237 is output. | A |
| DTC C1237 is not output. | B |
A
B