11302
1.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Apply a light coat of engine oil to 2 new oil pump gaskets and a new oil hole cover gasket.
Install the 2 oil pump gaskets and oil hole cover gasket to the stiffening crankcase assembly.
| *1 | Drive Rotor Spline |
| *2 | Crankshaft Timing Sprocket |
Align the drive rotor spline and crankshaft timing sprocket as shown in the illustration.
Apply seal packing in a line to the timing chain cover sub-assembly as shown in the following illustration.
| *a | 3.0 mm or more | *b | 7.0 mm or more |
| *c | 13.0 mm or more | - | - |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent.
| Area | Seal Packing Diameter (Round) | Distance from Edge of Cover to Center of Seal Packing | Seal Packing Application Length |
|---|---|---|---|
| Seal Packing Dimension (Flat) | |||
| Dashed Line | 2.5 to 3.5 mm (0.0984 to 0.138 in.) | 2.5 mm (0.0984 in.) | - |
| - | |||
| A - A | 2.5 to 3.5 mm (0.0984 to 0.138 in.) | 2.5 mm (0.0984 in.) | - |
| - | |||
| B - B | 5.0 mm (0.197 in.) | 3.0 mm (0.118 in.) | 28 mm (1.10 in.) |
| 7.0 mm (0.276 in.) or more wide and 3.0 mm (0.118 in.) or more thick | |||
| C - C | 7.0 mm (0.276 in.) | 5.0 mm (0.197 in.) | 25 mm (0.984 in.) |
| 13.0 mm (0.512 in.) or more wide and 3.0 mm (0.118 in.) or more thick | |||
| D - D | 5.0 mm (0.197 in.) | 3.0 mm (0.118 in.) | 26 mm (1.02 in.) |
| 7.0 mm (0.276 in.) or more wide and 3.0 mm (0.118 in.) or more thick | |||
| E | 2.5 to 3.5 mm (0.0984 to 0.138 in.) | 3.0 mm (0.118 in.) | - |
| - |
Clean the surfaces with non-residue solvent before applying seal packing.
Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.
After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.
Do not add engine oil for at least 2 hours after installation.
Do not start the engine for at least 2 hours after installation.
Temporarily install the timing chain cover sub-assembly with the 17 bolts and 2 nuts.
| *1 | Nut | - | - |
| *a | Torque | *b | Tightening Order |
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 30 mm (1.18 in.) | 8 mm (0.315 in.) |
| Bolt B | 35 mm (1.38 in.) | 10 mm (0.394 in.) |
| Bolt C | 45 mm (1.77 in.) | 8 mm (0.315 in.) |
Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.
Tighten the 17 bolts and 2 nuts in several steps, in the sequence shown in the illustration.
12315A
2.INSTALL ENGINE MOUNTING BRACKET RH
Install the engine mounting bracket RH with the 5 bolts in the order shown in the illustration.
After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.
11301C
3.INSTALL TIMING CHAIN COVER OIL SEAL
13471
4.INSTALL CRANKSHAFT PULLEY
11301K
5.INSTALL CRANKSHAFT POSITION SENSOR
16620
6.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
11201
7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
Apply a light coat of engine oil to 3 new camshaft bearing cap oil hole gaskets.
Install the 3 camshaft bearing cap oil hole gaskets.
| *1 | Upper Surface |
| *2 | Inner Lip |
| *3 | Outer Lip |
Visually check the spark plug tube gasket.
| Area | Specified Condition |
|---|---|
| Upper surface | No scratches or deformation |
| Outer lip | No scratches or deformation |
| Inner lip | No scratches |
If the result is not as specified, replace the spark plug tube gasket.
Install a new spark plug tube gasket to the cylinder head cover sub-assembly.
Remove any oil from the contact surface.
| *1 | Timing Chain Cover Sub-assembly |
| *2 | Camshaft Housing Sub-assembly |
| *a | Application width 5.0 mm (0.197 in.) |
| *b | 3.0 to 6.0 mm |
|
Seal packing |
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 6.0 mm (0.118 to 0.236 in.)
Remove any oil from the contact surface.
Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
| *1 | Seal Washer |
| *a | Pin A |
| *b | Pin B |
Align the cylinder head cover sub-assembly with pin (A). Then align the cylinder head cover sub-assembly with pin (B) and install the cylinder head cover sub-assembly.
Install 3 new seal washers and 16 bolts, and then tighten the bolts in the order shown in the illustration.
Do not apply engine oil for at least 2 hours after installation.
19500
8.INSTALL IGNITION COIL ASSEMBLY
82121
9.INSTALL ENGINE WIRE
10.INSTALL ENGINE AND TRANSAXLE