1.INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Engage the 5 guides and temporarily install the instrument panel safety pad assembly as shown in the illustration.
Do not damage the instrument panel safety pad assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.
Install the 2 clips.
Install the 3 bolts <B> and nut <F> or <G>.
Install the 2 passenger airbag bolts <A>.
Engage each clamp.
Connect each connector.
82142A
2.CONNECT NO. 2 INSTRUMENT PANEL WIRE
55011A
3.INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Engage the 10 clips to install the No. 1 instrument panel garnish sub-assembly.
58816B
4.INSTALL CONSOLE BOX INSERT
for RHD with Automatic Air Conditioning System:
Engage the 2 claws to connect the room temperature sensor.
Engage the clip and 3 guides.
Install the console box insert with the 2 screws <C> or <D>.
58817A
5.INSTALL FRONT NO. 2 CONSOLE BOX INSERT
for LHD with Automatic Air Conditioning System:
Engage the 2 claws to connect the room temperature sensor.
Engage the clip and 3 guides.
Install the front No. 2 console box insert with the 2 screws <C> or <D>.
55480D
6.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
for LHD with Smart Entry and Start System:
Connect the connector.
Engage the 4 clips to install the lower instrument panel finish panel assembly.
86160P
7.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
55408F
8.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 2 guides.
Engage the 3 claws and 2 clips to install the No. 1 instrument panel speaker panel sub-assembly.
62212
9.INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)
62212
10.INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)
86160P
11.INSTALL FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSTALLATION
55409F
12.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Engage the 2 guides.
Engage the 3 claws and 2 clips to install the No. 2 instrument panel speaker panel sub-assembly.
62211
13.INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
62211
14.INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
55670
15.INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 4 clips to install the No. 3 instrument panel register assembly.
55475A
16.INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Engage the 5 clips to install the No. 2 instrument cluster finish panel garnish.
55303B
17.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Engage the 2 clips and 4 guides.
Install the 3 screws <C> or <D>.
Close the lower instrument panel door.
Install the lower instrument panel sub-assembly with the bolt <B> and screw <C> or <D>.
55607
18.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect the connector.
Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.
55317A
19.INSTALL INSTRUMENT SIDE PANEL RH
Engage the 3 guides.
Engage the 4 claws to install the instrument side panel RH as shown in the illustration.
62311B
20.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
62111A
21.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
67911B
22.INSTALL FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>INSTALLATION
86160J
23.INSTALL FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)
55510F
24.INSTALL NO. 1 SPEAKER OPENING COVER ASSEMBLY
Connect the connector.
Engage the 8 clips to install the No. 1 speaker opening cover assembly.
25.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver)
Connect the connector.
Engage the 10 clips to the vehicle body to temporarily install the center instrument cluster finish panel with air conditioning control assembly.
Install the center instrument cluster finish panel with air conditioning control assembly with the 4 bolts.
26.INSTALL RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)
27.INSTALL NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)
58804A
28.INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
Connect each connector.
Engage the 4 clips and guide.
Install the upper console panel sub-assembly with the 2 screws <C> or <D>.
58916
29.INSTALL BOX BOTTOM MAT
Install the box bottom mat.
55660
30.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 6 clips to install the No. 2 instrument panel register assembly.
When installing the No. 2 instrument panel register assembly, check that the wire harness is not caught between the No. 2 instrument panel register assembly and duct.
31.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Connect the connector.
Engage the clamp.
Engage the 6 clips and 7 claws to install the center instrument cluster finish panel assembly.
32.INSTALL REAR CONSOLE BOX ASSEMBLY
58815A
33.INSTALL CONSOLE BOX CARPET
58864B
34.INSTALL NO. 4 CONSOLE BOX DUCT
58801E
35.INSTALL UPPER CONSOLE BOX SUB-ASSEMBLY
58805C
36.INSTALL REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
Connect each connector.
Engage the 4 clips and install the rear console upper panel sub-assembly.
Move the shift lever to P.
33504F
37.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
Turn the shift lever knob sub-assembly clockwise to install the shift lever knob sub-assembly.
53921B
38.INSTALL FRONT PANEL GARNISH RH
Engage the claw, 5 clips and 6 guides to install the front panel garnish RH.
39.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)
Engage the 5 clips and 3 guides.
Install the lower No. 1 instrument panel finish panel assembly with the 2 bolts <B>.
40.INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for RHD)
Connect each connector.
Engage the 4 claws, 9 clips and 3 guides.
Install the lower No. 1 instrument panel finish panel assembly with the 2 bolts <B>.
53601
41.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
53922B
42.INSTALL FRONT PANEL GARNISH LH
Engage the claw, 5 clips and 6 guides to install the front panel garnish LH.
83100
43.INSTALL COMBINATION METER ASSEMBLY
55410C
44.INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Temporarily install the instrument cluster finish panel assembly as shown in the illustration.
Connect each connector.
Engage the 5 claws, 5 clips and 2 guides to install the instrument cluster finish panel assembly.
Engage the 2 claws, 4 clips and 2 guides.
55650
45.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Engage the 4 clips to install the No. 1 instrument panel register assembly.
55474C
46.INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD)
Engage the 3 clips to install the No. 1 instrument cluster finish panel garnish.
55431B
47.INSTALL UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)
w/ Smart Entry and Start System:
Connect the connector.
Engage the 4 clips to install the upper instrument panel finish panel.
55318C
48.INSTALL INSTRUMENT SIDE PANEL LH
Engage the 3 guides.
Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
62312B
49.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
62112A
50.INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
67914
51.INSTALL FRONT DOOR SCUFF PLATE LH
52.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
53.INSPECT SRS WARNING LIGHT