Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2015.04
RM19V0EQ _58 Vehicle Interior _014606 THEFT DETERRENT / KEYLESS ENTRY _0074121 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (IG and ACC)  


DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.

·

With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.

·

When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.

·

When the smart entry and start system cancel function has been canceled on the customization menu, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.


HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


WIRING DIAGRAM

B298800E02
2.552,0.854 2.969,1.052 0.417,0.198 10 false CUTB 0.063,0.865 0.896,1.063 0.833,0.198 10 false from Battery 0.063,1.333 0.896,1.531 0.833,0.198 10 false from Battery 1.25,1.031 2.177,1.229 0.927,0.198 10 false ECU-B NO. 1 1.563,1.49 1.917,1.688 0.354,0.198 10 false AM2 2.552,1.302 2.781,1.5 0.229,0.198 10 false +B 2.552,1.75 2.708,1.948 0.156,0.198 10 false E 2.979,1.219 3.354,1.417 0.375,0.198 10 false IG1D 3.448,1.021 3.583,1.188 0.135,0.167 10 false 6 4.969,6.469 5.75,6.667 0.781,0.198 10 false ACC NO. 1 4.99,5.094 5.698,5.292 0.708,0.198 10 false IG1 NO. 4 4.99,1.521 5.698,1.719 0.708,0.198 10 false IG1 NO. 1 4.99,2.708 5.698,2.906 0.708,0.198 10 false IG1 NO. 2 4.99,3.896 5.698,4.094 0.708,0.198 10 false IG1 NO. 3 4.01,8.052 6.708,8.219 2.698,0.167 10 false Instrument Panel Junction Block Assembly 4.99,7.604 5.771,7.802 0.781,0.198 10 false ACC NO. 2 1.021,3.198 1.333,3.365 0.313,0.167 10 false SS1 1.01,3.656 1.323,3.823 0.313,0.167 10 false SS2 0.875,4.083 1.344,4.281 0.469,0.198 10 false AGND 1.406,3.094 1.542,3.26 0.135,0.167 10 false 5 1.406,3.99 1.542,4.156 0.135,0.167 10 false 6 1.406,3.531 1.542,3.698 0.135,0.167 10 false 1 2.542,3.208 2.979,3.375 0.438,0.167 10 false SSW1 2.542,3.667 2.979,3.833 0.438,0.167 10 false SSW2 2.542,4.094 3.01,4.292 0.469,0.198 10 false AGND 0.51,4.406 0.823,4.573 0.313,0.167 10 false I58 0.51,4.563 1.469,4.729 0.958,0.167 10 false Engine Switch 0.771,5.271 0.906,5.438 0.135,0.167 10 false 2 1.563,5.271 1.698,5.438 0.135,0.167 10 false 1 2.229,5.208 2.448,5.375 0.219,0.167 10 false 18 2.521,5.406 2.927,5.604 0.406,0.198 10 false STP1 0.542,5.708 0.854,5.875 0.313,0.167 10 false A33 0.542,5.865 2.313,6.031 1.771,0.167 10 false Stop Light Switch Assembly 1.906,8 3.729,8.365 1.823,0.365 10 false Certification ECU (Smart Key ECU Assembly) 0.708,6.792 1.313,6.99 0.604,0.198 10 false STOP 1.417,6.646 2.323,6.813 0.906,0.167 10 false from Battery 2.26,3.01 2.479,3.177 0.219,0.167 10 false 28 2.26,3.469 2.479,3.635 0.219,0.167 10 false 30 2.26,3.906 2.479,4.073 0.219,0.167 10 false 24 2.24,3.208 2.563,3.375 0.323,0.167 10 false I78 2.25,4.104 2.573,4.271 0.323,0.167 10 false I78 2.25,3.646 2.573,3.813 0.323,0.167 10 false I78 2.208,5.375 2.531,5.542 0.323,0.167 10 false A43 2.25,0.719 2.469,0.885 0.219,0.167 10 false 10 2.281,1.167 2.417,1.333 0.135,0.167 10 false 2 2.26,1.625 2.479,1.792 0.219,0.167 10 false 11 2.198,0.896 2.521,1.063 0.323,0.167 10 false A43 2.208,1.802 2.531,1.969 0.323,0.167 10 false A43 2.208,1.354 2.531,1.521 0.323,0.167 10 false A43 3.396,1.208 3.719,1.375 0.323,0.167 10 false I78 3.906,0.802 4.146,0.969 0.24,0.167 10 false 3E 3.885,0.604 4.188,0.771 0.302,0.167 10 false 1*1 3.906,1.219 4.146,1.385 0.24,0.167 10 false 3A 3.927,1.031 4.167,1.198 0.24,0.167 10 false 27 6.531,3.177 6.75,3.344 0.219,0.167 10 false 3C 6.531,0.802 6.75,0.969 0.219,0.167 10 false 3D 6.542,0.615 6.781,0.781 0.24,0.167 10 false 33 5.885,0.979 6.635,1.177 0.75,0.198 10 false BKUP LP 6,2.167 6.594,2.646 0.594,0.479 10 false ECU-IG1 NO.1 6.542,1.792 6.781,1.958 0.24,0.167 10 false 36 6.531,2.979 6.771,3.146 0.24,0.167 10 false 33 5.958,5.927 6.771,6.135 0.813,0.208 10 false ECU-ACC 6.542,5.542 6.781,5.708 0.24,0.167 10 false 37 6.542,6.698 6.781,6.865 0.24,0.167 10 false 32 6.604,7.229 6.844,7.396 0.24,0.167 10 false 7 6.031,6.99 6.458,7.531 0.427,0.542 10 false SFT LOCK -ACC 6.521,1.99 6.74,2.156 0.219,0.167 10 false 3D 6.521,5.729 6.74,5.896 0.219,0.167 10 false 3B 6.542,6.885 6.76,7.052 0.219,0.167 10 false 3A 6.542,7.406 6.76,7.573 0.219,0.167 10 false 3B 2.896,6.135 3.333,6.333 0.438,0.198 10 false ACCD 3.438,5.948 3.573,6.115 0.135,0.167 10 false 4 3.385,6.146 3.708,6.313 0.323,0.167 10 false I78 3.927,6.146 4.146,6.313 0.219,0.167 10 false 3B 3.938,5.969 4.177,6.135 0.24,0.167 10 false 23 0.25,8.073 1.156,8.24 0.906,0.167 10 false *1: for LHD 0.25,8.365 1.156,8.531 0.906,0.167 10 false *2: for RHD 4.24,0.802 4.479,0.969 0.24,0.167 10 false 3F 4.229,0.604 4.531,0.771 0.302,0.167 10 false 1*2 6.042,3.396 6.656,3.792 0.615,0.396 10 false ECU-IG1 NO.3

B298915E13
3.823,1.865 4.125,2.063 0.302,0.198 10 false IG2 3.104,1.552 3.375,1.719 0.271,0.167 10 false 1C 3.156,1.365 3.292,1.531 0.135,0.167 10 false 8 4.646,1.552 4.906,1.719 0.26,0.167 10 false 1E 4.698,1.375 4.833,1.542 0.135,0.167 10 false 2 3.26,2.24 4.865,2.438 1.604,0.198 10 false No. 1 Integration Relay 1.531,1.552 1.906,1.75 0.375,0.198 10 false IG2D 2.031,1.375 2.167,1.542 0.135,0.167 10 false 9 0.719,3.26 2.646,3.604 1.927,0.344 10 false Certification ECU (Smart Key ECU Assembly) 1.948,1.552 2.302,1.74 0.354,0.188 10 false A43

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS

·

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>DTC CHECK / CLEAR).

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).

·

Before replacing the certification ECU (smart key ECU assembly) or electrical Key transmitter sub-assembly, refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)
Power Source Control
·

Start Switch1

·

Start Switch2

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

ACC Relay Monitor


-


PROCEDURE

1.CHECK WIRELESS DOOR LOCK CONTROL SYSTEM
a.

Check the wireless door lock function by operating the electrical key transmitter sub-assembly.

OK:

Wireless door lock function operates.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

3.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

3.CHECK HARNESS AND CONNECTOR (GROUND)

OK

4.CHECK SMART ENTRY AND START SYSTEM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SMART ENTRY AND START SYSTEM
a.

Remove the transmitter battery from the electrical key transmitter sub-assembly.

Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT


b.
B388893C03
2.198,1.063 2.948,1.219 false 0.531,0.427 1.281,0.583 false 0.365,0.333 0.677,0.531 0.313,0.198 10 false *1 3,1.156 3.313,1.354 0.313,0.198 10 false *2
*1 Engine Switch
*2 Electrical Key Transmitter Sub-assembly


With the brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.

OK:

The power source mode changes.


HINT:

If the power source mode changes, the cabin verification is malfunctioning.



Result:
Result Proceed to
The power source mode does not change. A
The power source mode changes. B



A

5.READ VALUE USING INTELLIGENT TESTER

B

11.READ VALUE USING INTELLIGENT TESTER
5.READ VALUE USING INTELLIGENT TESTER
a.

Connect the intelligent tester to the DLC3.


b.

Turn the intelligent tester on.


c.

Enter the following menus: Body / Power Source Control / Data List.


d.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The engine cannot be started when this item is OFF.

·

When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

ON (brake pedal is depressed) and OFF (brake pedal is released) appear on the screen.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING INTELLIGENT TESTER

NG

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
6.READ VALUE USING INTELLIGENT TESTER
a.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 223 18

b.

With the engine switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly (key) near the engine switch for 2 seconds or more and read the Data List.

OK:

IG2 ON is displayed in the Data List.


HINT:

If the smart entry and start system function has been canceled on the customization menu, ACC ON is displayed in the Data List.



Result:
Proceed to
OK
NG



OK

7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

8.CHECK FOR DTC
7.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Read the Data List according to the display on the intelligent tester.


b.

Measure the voltage according to the value(s) in the table below.

B264896C20
0.302,0.29 0.488,0.451 0.186,0.161 10 *a 4.729,0.887 5.126,1.126 0.397,0.238 4.841,0.934 5.136,1.091 0.296,0.157 10 I78 2.111,0.885 2.508,1.123 0.397,0.238 2.187,0.932 2.482,1.088 0.296,0.157 10 A43 4.388,1.629 4.096,2.312 false 1.978,1.736 1.704,2.287 false 3.927,2.312 4.29,2.468 0.363,0.157 10 IG1D 1.531,2.313 1.894,2.469 0.363,0.157 10 IG2D 4.538,1.626 4.834,2.311 false 4.647,2.325 5.076,2.482 0.429,0.157 10 ACCD
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
- -



c.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)
IG1 ON: Engine switch on (IG) (IG1 relay on)
IG2 ON: Engine switch on (IG) (IG2 relay on)
ST ON: Sending engine start request signal
Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

d.

Measure the voltage while checking the Data List on the intelligent tester.

Standard Voltage:
Tester Connection Condition Specified Condition
I78-6 (IG1D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
A43-9 (IG2D) - Body ground Engine switch off 1 V or less
Engine switch on (ACC) 1 V or less
Engine switch on (IG) 9 V or higher
I78-4 (ACCD) - Body ground Engine switch off 1 V or less
Engine switch on (IG) 8.5 V or higher
Engine switch on (ACC) 8.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

8.CHECK FOR DTC
a.

Enter the following menus: for Entry&Start:

Body / Entry&Start / Trouble Codes.


b.

Check for DTCs.

Body Electrical > Power Source Control > Trouble Codes
50001 223
Result:
Result Proceed to
The following DTCs are not output:
·

B2784

·

B278A


A
DTC B2784 is output. B
DTC B278A is output. C




A

REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

B

C

9.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Disconnect the A33 connector from the stop light switch assembly.


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.READ VALUE USING INTELLIGENT TESTER
a.

Read the Data List according to the display on the intelligent tester.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Start Switch1 Engine switch 1 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

If the engine switch is pressed for a short time, the display may not change.

·

Use this item to determine whether the engine switch input signal is malfunctioning.


Start Switch2 Engine switch 2 status ON or OFF ON: Engine switch pressed
OFF: Engine switch not pressed
·

Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

·

Behaves the same way as engine switch 1.


Body Electrical > Power Source Control > Data List
Tester Display
Start Switch1
Start Switch2
50003 223 4,5
OK:

ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.


Result:
Result Proceed to
NG A
OK B




A

12.INSPECT ENGINE SWITCH

B

12.INSPECT ENGINE SWITCH
a.

Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)

NG

13.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)
a.

Disconnect the I78 connector from the certification ECU (smart key ECU assembly).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I78-28 (SSW1) - I58-5 (SS1) Always Below 1 Ω
I78-30 (SSW2) - I58-1 (SS2) Always Below 1 Ω
I78-28 (SSW1) or I58-5 (SS1) - Body ground Always 10 kΩ or higher
I78-30 (SSW2) or I58-1 (SS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR