Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER(for LHD) › 2015.04–2016.05
RM19V0EQ _54 Brake _014592 BRAKE SYSTEM (OTHER) _0074044 BRAKE MASTER CYLINDER(for LHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for LHD)  INSTALLATION  


PROCEDURE

Hide 47201B 1.INSTALL BRAKE MASTER CYLINDER O-RING

a.

Install a new brake master cylinder O-ring to the brake master cylinder sub-assembly.


Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:

When installing a new brake master cylinder sub-assembly, remove the protectors from the master cylinder piston and outlet ports.


a.
C243055C01
0.948,2.729 1.042,2.854 0.094,0.125 6 .
V100145

Apply Grease


Apply a light layer of a grease enclosed with a new brake master cylinder sub-assembly or lithium soap base glycol grease to the circumference of the brake master cylinder sub-assembly and inner surface of the brake booster assembly as shown in the illustration.


b.
C239864C01
2.729,3.667 3,3.667 false 3,3.594 3.375,3.875 0.375,0.281 10 *1
*1 Master Cylinder Piston


Install the brake master cylinder sub-assembly and front brake tube way to the brake booster assembly with the 2 nuts.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)

NOTICE:
·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its reservoir when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, and do not cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of cloth and then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Do not kink or damage the brake lines.

·

Do not allow brake lines to twist and interfere with other parts or vehicle body during flexible hose tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines.




c.
C239865N01
1.104,1.625 0.979,1.99 0.979,1.99 1.49,1.844 false 1.688,0.604 0.896,0.479 0.896,0.479 1.344,1.188 false 2.406,0.781 2.688,1.573 2.688,1.573 1.76,1.427 false 0.854,1.896 1.302,2.083 0.448,0.188 10 false a 0.792,0.375 1.063,0.635 0.271,0.26 10 false b 2.708,1.479 3.042,1.802 0.333,0.323 10 false b

Using a union nut wrench, connect the 6 brake lines and install the brake master cylinder to way tube to the brake master cylinder sub-assembly.

Torque:
flare nut a : 15 N*m (155 kgf*cm, 11 ft.*lbf)
flare nut b (w/o VSC) : 15 N*m (155 kgf*cm, 11 ft.*lbf)
flare nut b (w/ VSC) : 20 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow brake lines to twist and interfere with other parts or vehicle body during flexible hose tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION




d.

Connect the reservoir level switch connector and engage the clamp.


Hide 3.BLEED BRAKE SYSTEM

Hide 4.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 5.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17735 6.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 7.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 8.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 55702A 9.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

a.

Install the front outer cowl top panel sub-assembly with the 10 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.


Hide 10.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY