Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2015.04–2016.05
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073931 ENGINE ASSEMBLY A

2AR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the manual transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the manual transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust from the moving section could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.


HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 1.REMOVE ENGINE STAND

a.

Using a chain block and engine sling device, secure the engine assembly.

NOTICE:
·

Adjust the angle of the sling device carefully to prevent the engine assembly or engine hanger from deforming or becoming damaged.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.




b.

Remove the engine stand from the engine.


Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 12315A 4.INSTALL ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket RH with the 3 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 43457 5.INSTALL DRIVE SHAFT BEARING BRACKET

a.

Install the drive shaft bearing bracket with the 3 bolts.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 12361A 6.TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Temporarily install the front engine mounting insulator with the bolt.


Hide 12372A 7.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH

a.

Temporarily install the engine mounting insulator LH with the nut.


Hide 12362A 8.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH

a.

Temporarily install the engine mounting insulator RH with the nut.


Hide 51100G 9.INSTALL FRONT FRAME ASSEMBLY

a.

Install the front frame assembly with the 9 nuts.

A172973C08
0.469,0.25 0.656,0.438 0.188,0.188 10 false *a 2.375,0.229 2.573,0.417 0.198,0.188 10 false *b 4.865,0.219 5.073,0.406 0.208,0.188 10 false *c 0.177,1.938 0.313,2.104 0.135,0.167 10 false A 0.688,1.573 0.823,1.74 0.135,0.167 10 true A 1.469,1.823 1.604,1.99 0.135,0.167 10 true A 3.021,0.958 3.156,1.125 0.135,0.167 10 false B 3.448,1.385 3.583,1.552 0.135,0.167 10 false B 3.604,0.802 3.74,0.969 0.135,0.167 10 true B 5.406,1.052 5.542,1.219 0.135,0.167 10 true B 6.01,1.094 6.146,1.26 0.135,0.167 10 false B 6.219,1.979 6.354,2.146 0.135,0.167 10 false B
*a Front Side *b RH Side
*c LH Side - -


Torque:
A : 52 N*m (530 kgf*cm, 38 ft.*lbf)
B : 87 N*m (887 kgf*cm, 64 ft.*lbf)


b.

Install the 4 hole plugs.


c.

Tighten the bolt and 2 nuts.

A265024C02
0.344,0.198 1.292,0.438 0.948,0.24 10 false *a 2.885,0.198 3.708,0.417 0.823,0.219 10 false *b 1.094,1.344 1.229,1.51 0.135,0.167 10 true A 3.792,0.615 3.927,0.781 0.135,0.167 10 true B 5.927,0.563 6.063,0.729 0.135,0.167 10 true C 5.167,0.198 5.99,0.417 0.823,0.219 10 false *c
*a Front Side *b LH Side
*c RH Side - -


Torque:
A : 87 N*m (887 kgf*cm, 64 ft.*lbf)
B : 95 N*m (969 kgf*cm, 70 ft.*lbf)
C : 95 N*m (969 kgf*cm, 70 ft.*lbf)


Hide 43420G 10.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43420 11.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 12.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

Hide 27020 13.INSTALL GENERATOR ASSEMBLY

Hide 88310 14.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

Hide 82121 16.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine with transaxle.


Hide 17.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on an engine lifter.

NOTICE:
·

Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.

·

Do not position a height adjustment attachment or plate lift attachment onto the front frame assembly.

·

To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.

·

Make sure to support the engine assembly with transaxle securely to prevent it from falling.





c.

Install the engine assembly to the vehicle.

NOTICE:

Do not raise the engine more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


HINT:
·

Make sure that the engine is clear of all wiring and hoses.

·

While raising the engine into the vehicle, do not allow it to contact the vehicle.




d.
A255454N06
2.198,3.031 2.344,3.198 0.146,0.167 10 false C 1.125,3.021 1.271,3.188 0.146,0.167 10 false C 0.677,1.344 0.823,1.51 0.146,0.167 10 true A 2.635,1.333 2.781,1.5 0.146,0.167 10 true A 1.01,0.083 1.156,0.25 0.146,0.167 10 false B 2.615,0.104 2.76,0.271 0.146,0.167 10 false B 3.135,0.323 3.281,0.49 0.146,0.167 10 false B 0.167,0.313 0.313,0.479 0.146,0.167 10 false B 3.156,2.417 3.302,2.583 0.146,0.167 10 false D 2.708,3.188 2.854,3.354 0.146,0.167 10 true D 0.167,2.417 0.313,2.583 0.146,0.167 10 false D 0.542,3.188 0.688,3.354 0.146,0.167 10 false D

Install the frame side rail plate RH and LH with the 4 bolts and 2 nuts.

Torque:
A : 85 N*m (867 kgf*cm, 62 ft.*lbf)
B : 32 N*m (326 kgf*cm, 24 ft.*lbf)


e.

Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.

Torque:
C : 85 N*m (867 kgf*cm, 62 ft.*lbf)
D : 32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Hide 32101A 18.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
A192239C51
1.374,0.672 1.576,0.828 0.203,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false
*1 Adhesive


Apply a few drops of adhesive to the first 2 or 3 threads of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.
A196626

Turn the crankshaft to gain access to the installation locations of the 6 torque converter assembly setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)

NOTICE:

Install the black colored bolt first, and then the 5 silver colored bolts.



Hide 11361J 19.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover.


Hide 45220 20.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 43502C 21.INSTALL FRONT AXLE ASSEMBLY LH

Hide 43501C 22.INSTALL FRONT AXLE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 23.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 24.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 25.INSTALL TIE ROD ASSEMBLY LH

Hide 45460 26.INSTALL TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89543 27.INSTALL FRONT SPEED SENSOR LH

Hide 89542 28.INSTALL FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 29.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 30.INSTALL FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43502H 31.INSTALL FRONT AXLE SHAFT NUT LH

Hide 43501H 32.INSTALL FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 17410 33.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 23901 34.CONNECT FUEL TUBE SUB-ASSEMBLY

a.
B012944

Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.

NOTICE:
·

Check for damage or contamination on the connected part of the pipe.

·

Check if the pipe and the connector are securely connected by trying to pull them apart.




b.
A210152

Install the No. 1 fuel pipe clamp.


Hide 88711 35.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88704 36.INSTALL SUCTION HOSE SUB-ASSEMBLY

Hide 44774 37.CONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

a.

Connect the union to connector tube hose.


Hide 44773F 38.CONNECT UNION TO CHECK VALVE HOSE (for RHD)

a.

Connect the union to check valve hose.


Hide 12309 39.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

a.
A255452

Temporarily install the engine moving control rod sub-assembly with the 4 bolts.


b.

Fully tighten the engine moving control rod sub-assembly with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 82284 40.INSTALL EARTH WIRE

a.

Install the earth wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 12327A 41.INSTALL NO. 2 ENGINE MOUNTING STAY RH

a.

Install the No. 2 engine mounting stay RH with the 2 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 33820B 42.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.


b.

Connect the transmission control cable assembly to the control shaft lever with the nut.

Torque:
13 N*m (131 kgf*cm, 9 ft.*lbf)

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.



c.

Connect the wire harness clamp.


Hide 17771A 43.INSTALL NO. 1 AIR CLEANER BRACKET

a.

Install the No. 1 air cleaner bracket to the battery carrier with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Connect the 2 wire clamps.


Hide 82121 44.CONNECT ENGINE WIRE

a.
A255463

Connect the 2 wire clamps.


b.

Connect the connector to the ECM with the lock lever.


c.
A255437

Connect the engine wire to the engine room relay block.


d.

Connect the wire clamp and install the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


e.

Install the No. 1 relay block cover.


Hide 28100 45.INSTALL STARTER ASSEMBLY

Hide 87245 46.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose.


Hide 87246 47.CONNECT OUTLET HEATER WATER HOSE (for LHD)

a.

Connect the outlet heater water hose.


Hide 87246 48.CONNECT OUTLET HEATER WATER HOSE (for RHD)

a.

Connect the 3 heater outlet water hoses.


Hide 32941 49.CONNECT INLET NO. 1 OIL COOLER HOSE

a.

Connect the inlet No. 1 oil cooler hose to the automatic transaxle assembly.


Hide 32942 50.CONNECT OUTLET NO. 1 OIL COOLER HOSE

a.

Connect the outlet No. 1 oil cooler hose to the automatic transaxle assembly.


Hide 16571C 51.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose.


b.

Connect the air fuel ratio sensor wire to the No. 1 radiator hose with the hose clamp.


Hide 16572D 52.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose.


Hide 53.INSTALL BATTERY

a.

Install the battery and battery tray.


b.

Install the battery clamp with the bolt and nut.

Torque:
Bolt : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
Nut : 3.5 N*m (36 kgf*cm, 31 in.*lbf)


c.

Connect the positive (+) battery terminal

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


Hide 54.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.
A305724C01
2.229,0.958 2.583,1.115 true 2.667,0.833 2.896,0.833 true 2.094,0.844 2.406,1 0.313,0.156 10 false *1 2.906,0.74 3.104,0.906 0.198,0.167 10 false *2
*1 Hole
*2 Projection


Insert the projection of the air cleaner case sub-assembly to the hole of the No. 2 air cleaner bracket as shown in the illustration.


b.

Tighten the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.

Connect the wire harness clamp.


Hide 17801 55.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 56.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 57.INSTALL INLET AIR CLEANER ASSEMBLY

a.

Install the inlet air cleaner assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 58.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 59.ADD ENGINE OIL

Hide 63. WARM UP ENGINE

Hide 65.INSPECT FOR OIL LEAK

Hide 67.INSPECT FOR EXHAUST GAS LEAK

Hide 12601B 72.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY

a.

Engage the 3 pins and install the No.1 engine cover sub-assembly.


Hide 53295E 73.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53737B 75.INSTALL FRONT FENDER APRON SEAL LH

Hide 53736 76.INSTALL FRONT FENDER APRON SEAL RH

Hide 51442C 77.INSTALL ENGINE UNDER COVER LH

Hide 53852K 78.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 51441C 79.INSTALL ENGINE UNDER COVER RH

Hide 53851Z 80.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 81.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 82.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT